Main Terminal Description; Section 2 - Programming; Programming Methods - DKS 1812 Classic Installation & Owner's Manual

1.11 Main Terminal Description

Phone In
1. Phone In (Negative - Ring)
(Twisted Pair)
OR
1. Phone In (Negative - Ring)
Wireless
Adapter
2. Phone In (Positive - Tip)
(Polarity Matters!)
3. Ground (Required)
4. Phone Out (Positive - Tip)
Phone Out
(Twisted Pair)
5. Phone Out (Negative - Ring)
Time Clock
6. External Time Clock Input. Connect Common to terminal 9.
Emergency
7. Switch Input Relay 1. A switch closure across terminals 7 & 9
and/or Postal
will activate relay 1 for its programmed strike time.
Entry Switch
8. Switch Input Relay 2. A switch closure across terminals 8 & 9
will activate relay 2 for its programmed strike time.
Back-Up
9. - 24 VDC Battery Negative. Also Common for terminals 6, 7 & 8.
Battery Power
10. + 24 VDC Battery Positive.
11. Relay 1 Normally Open
Relay 1
12. Relay 1 Normally Closed
(Access Control Device)
13. Relay 1 Common
14. Relay 2 Normally Open
Relay 2
15. Relay 2 Normally Closed
(Access Control Device)
16. Relay 2 Common
17. 24 VAC Input Power
Input Power
(Transformer)
18. 24 VAC Input Power
Before You Start Programming: IMPORTANT! Make sure the 1812 has power and we strongly suggest that you become
familiar with these programming instructions before beginning any programming of the 1812 Classic system.
The 1812 has been programmed at the factory with many of the programming parameters already set (default setting) for a
typical residential application with a single 1812. There is no need to reprogram these parameters unless you want to change
them. For easy reference, refer to the chart on page 22 that list the various programming functions and their default settings.

2.1 Programming Methods

The 1812 Classic can be programmed from the system keypad (Keypad on the 1812) or from a touch-tone telephone connected
to the system.
Direct "System Keypad"
1 1 1 1 1
4 4
7 7
• System Keypad (Preferred)
We strongly recommend that you become familiar with the entire programming sequence before attempting to program
some of the more complex features of this system using the system keypad. If you make a single error in the program-
ming steps, you will have to re-do the sequence from the beginning.
• Touch-Tone Telephone
The programmable features that can be programmed using the system keypad can also be programmed using a touch-
tone telephone (typically the house phone) connected to the 1812. This method of programming is useful for program-
ming simple steps or for turning certain features ON or OFF, but is not recommended for complex programming steps.
1812-065-V-12-14

SECTION 2 - PROGRAMMING

2 2 2 2 2 3 3 3 3 3 3 3 Push Button Push Button
To Call To Call
5 5 6 6
8 8 9 9
0 0
External time clock input may be
used to create an additional time
zone for access codes (4.14).
1
2
3
4
5
6
7
8
ON
9
10
MAS MAS MASTER
11
Relay 1
CO CODE DE
Note: Each relay can control a
12
(11-13)
normally open OR normally close
13
access control device. Relay
14
Relay 2 contacts are rated for 3 amps @
15
30 VAC maximum.
(14-16)
16
1871-010
17
18
Touch-Tone Telephone
connected directly to
the system or off-site.
Wireless Adapter
DO NOT wire the
wireless adapter to the
PHONE OUT main
terminal connection.
Please refer to the
"Wireless Adapter"
manual 1815-560 for
correct wiring.
19