Wire One 1812 To A Telco Line - Telephone Mode - DKS 1812 Classic Installation & Owner's Manual

1.6 Wire One 1812 to a Telco Line - Telephone Mode

Connect to Incoming Telephone
Company's Phone Line
Locate the telephone company demarcation device.
IMPORTANT Identify the wires that connect to the
homeowner's telephone. Disconnect these 2 wires from
the demarcation device and connect them to terminals
#7 and #8 HOME on the by-pass board.
Connect a new twisted-pair telephone wire to the
telephone company demarcation device where the 2
wires were just removed from. Connect the other end of
the new twisted-pair wire to CENTRAL OFFICE terminals
#1 and #2 on the by-pass board (Unless using a surge
suppressor, then wire to surge board first).
Place the by-pass switch in the "By-Pass" position until
the 1812 installation is complete. Test the homeowner's
telephone. It should have a dial tone while the switch is
in the "By-Pass" position. See page 11.
Telephone
Locate Homeowner's
Company
Phone Line Inside Device
Demarcation
Point
Tip
Ring
Tip
Ring
Tip
Ring
Central Office (C.O.)
TIP (+): White/blue mark
Demarcation Device
RING (-): Blue/white mark
Access Control Devices
"Normally Open"
Vehicular
Gate Operator
Use minimum 18
AWG wire for runs
up to 100 feet.
W A
R N
IN
G
MO VIN
SER IOU G GA 16 AWG wire for
Oper S INJ TE
and free ate gate UR CA Y OR CAU N
Do not peop of only when DEA SE
or allow oper ate child le and gate obstr area TH
path Do not gate. ren to uctio is in
stand while in play in ns. sight
Read owne gate is gate movi path gate area
r's man ng. or walk
and ual throu gh
safet y instr
uctio ns.
CON ANS FOR runs up to 200 feet.
MS I/UL -325 TO
CAN CER /CSA TIFI
VEH C22 ED .2 TO
CLA ICU LAR NO. 247 53382
SS GAT
MOD EL E OPE RAT
SER HP OR
IAL
VOL TS
AMP
MAX S
GAT E LOA PHA SE
Door D Hz 60
King , Inc.,
Ingle (Term. 11 and 13)
d, woo
CA
Separate UL
Listed Power
Pedestrian
Transformer
Gate/Door
Electric
Strike
"Normally Close" with Maglock
(Terminal 15 and 16)
"Normally Open" with Electric Strike
(Terminal 14 and 16)
Magnetic locks or electric strikes must be
powered from a separate UL Listed power
transformer. DO NOT power strikes or magnetic
locks from the 1812 power transformer. Use
minimum 18 AWG wire for runs up to 100 feet;
16 AWG wire for runs up to 200 feet. It is
recommended to keep power wire runs as short
as possible.
14
Phone Line Surge Suppressor
DoorKing Surge Suppressor
P/N 1877-010 (or equivalent) is
optional but highly recommended.
For best protection, surge suppressor
ground wire MUST be 3-ft. or less in
length. Use minimum 12 AWG wire.
Refer to instruction sheet included
with surge board for complete
information.
PHONE LINE
INPUT OUTPUT
TIP RING GND GND TIP RING
"Existing"
Alarm
System
Location
RJ31x
Cat5e
Cat5e Without Surge Board
Phone Jack
installed
Before 1812
System
Be sure to properly
ground ALL boards.
See previous page
To "Existing"
for acceptable
Alarm Control Panel
grounding sources.
Single 1812 Wiring Configuration
ENTRY BY-PASS
SW1
1875-010
EARTH
GND
1 2 3 4 5 6 7 8
CENTRAL PHONE PHONE
HOME
OFFICE IN OUT
Homeowner's
Phone
Phone In
Phone
Out
LAN/Cordless
Company
Phone In
Push Button Push Button
Phone Mode
To Call To Call
4 4 5 5 6 6
7 7 8 8 9 9
0 0
Phone Out
Supplied Transformer
Polarity does not matter.
t p u
O u
V A
2 4
V A
2 0
The 1812 Classic operates ONLY on
24 VAC. Use the supplied power
transformer, 24 VAC, 20 VA (or UL
listed equivalent) to power the
telephone entry system. DO NOT
power any other devices (electric
strikes, magnetic locks, additional
1812s etc.) from the 1812's power
transformer.
See previous page for wire size
and run distances.
By-Pass Board
The By-Pass board is NOT optional and
must be installed as part of the 1812
"Telephone Mode" system.
See page 11 for complete information.
Single 1812:
PHONE IN #3 connects to Main Term #1.
PHONE IN #4 connects to Main Term #2.
PHONE OUT #5 connects to Main Term #5.
PHONE OUT #6 connects to Main Term #4.
1877-010
ENTRY BY-PASS
EARTH
GND
1 2 3 4
CENTRAL PHONE
OFFICE IN
Telephone
Line
For complete
Orange
information,
Pair
see page 12.
Cat5e
Ground
12 AWG Min.
Ground
12 AWG Min.
Phone
Terminal
Orange Pair
Green Pair
t
C
OUT OUT GND GND IN IN
OUTPUT INPUT
LOW VOLTAGE LINE
Ground
12 AWG Min.
Within 3 ft
of Surge Board
1878-010
Check Polarity of
Telephone Line
Check for polarity on the
incoming telephone line to each
board and maintain polarity
throughout the telephone line.
One potential problem checked
when a malfunction occurs in a
telephone entry system is to
see if the telephone line has
been wired to each board with
the correct polarity.
SW1
Test Example: By-pass board's
CENTRAL OFFICE terminals #1
1875-010
and #2. Terminal #2 must be
5 6 7 8
PHONE
HOME
positive (Tip +) with respect to
OUT
terminal #1 (Ring -). Set a VOM
meter to measure DC volts.
Place the positive lead on
terminal #2 and the negative
lead on terminal #1. If the
meter shows a positive voltage
Green
- OK. If the meter shows a
Pair
negative voltage (needle moves
off scale to the left), reverse the
wires on terminals #1 and #2.
Homeowner's
LAN/Cordless Phones
Older Lines
Red Wire (-)
RING
TIP
Older Lines
Green Wire (+)
Phone
Jack
Main
1 Phone In
RING
(1-2)
2
TIP
3
GND
4
Phone Out
TIP
(4-5)
5
RING
1871-010
6
7
8
ON
9
10
MASTER MAST MAST
11
N.O.
Relay 1
CODE COD E
Note: Each relay can control a
12
N.C.
(11-13)
normally open OR normally close
13
Com
access control device. Relay
14
N.O.
Relay 2 contacts are rated for 3 amps @
15
N.C.
30 VAC maximum.
(14-16)
16
Com
Power
17
24
VAC (17-18)
18
Low Voltage Surge Suppressor
DoorKing Surge Suppressor P/N 1878-010 (or
equivalent) is optional but highly recommended.
For best protection, surge suppressor ground wire
MUST be 3-ft. or less in length. Use minimum 12 AWG
wire. Refer to instruction sheet included with surge
board for complete information.
Phone
Jack
1812-065-V-12-14