Moxa Technologies CN2610 Series Quick Installation Manual

CN2610 Series
Quick Installation Guide
Third Edition, May 2006
1. Overview
Welcome to Moxa CN2600 Dual LAN Console Server, a communication
server with 8/16 asynchronous RS-232 ports and Dual 10/100 Mbps
Ethernet LAN port. CN2600 Dual LAN Console Server can be used to
connect terminals, modems, printers, and other asynchronous serial
devices to LAN hosts. CN2600 complies with TCP/IP and IEEE 802.3
specifications using standard Ethernet 10/100BaseT and twisted pair
10/100BaseTX cable as the physical medium.
2. Package Checklist
CN 2600 Dual LAN Console Server products are shipped with the
following items:
1 CN 2600 Dual LAN Console Server
1 Ac power Cord ( only for CN2610-16 or CN2610-8)
1CD-ROM
Quick Installation Guide
1 RJ45 Loopback Tester
Product Warranty Booklet
Rackmount kit including 2 brackets and 8 screws
1 CBL-RJ45F9-150
1 CBL-RJ45M25-150
Optional Accessories
CBL-RJ45M9-150 RJ45 8-pin to DB9 Male cable, 150 cm
CBL-RJ45F9-150 RJ45 8-pin to DB9 Female cable, 150 cm
CBL-RJ45M25-150 RJ45 8-pin to DB25 Male cable, 150 cm
CBL-RJ45F25-150 RJ45 8-pin to DB25 Female cable, 150 cm
NOTE: Notify your sales representative if any of the above items is
missing or damaged.
21
3. Hardware Introduction
Front Panel
— 1 —
LED
Reset
Ready
Ready
Serial Tx
Serial Rx Yellow Displays serial port reception.
Real Panel
Connector
AC Power
Input
Power On/Off
Switch
RS-232
Console Port
LAN1
LAN2
Serial Ports
LCM Display
We recommend using the LCM display and four push buttons to
configure the IP address for the first time.
Basic Operation
If the CN2600 is working properly, the LCM panel will display a green
color. The red Ready LED will also light up, indicating that the CN2600
is receiving power. After the red Ready LED turns to green, you will see
a display similar to:
C N 2
1 9 2
CN2610-16
03
192.168.127.254
There are four push buttons on CN2600's nameplate. Going from left to
right, the buttons are:
P/N: 1802026000200
Color Description
If you forget the password, press this button for 5
seconds, then the system will be returned to factory
default.
Use tools with sharp end to press Reset button
None continuously. The Ready LED will keep blinking
when your press the Reset button. After releasing
the Reset button, you will hear Bi-Bi sound,
meaning the default settings are restored and
CN2600 has rebooted.
Red Displays CN2600 system is powered on.
Green Displays CN2600 system is ready.
Green Displays serial port transmission.
Function
Automatic detection of 100-240V, 47-63Hz AC power
supply (CN2610-16 or CN2610-8).
I indicates power on; O indicates power off
One RJ45 connector for console terminal connection
Auto detecting 10/100 Mbps port
Auto detecting 10/100 Mbps port
8 or 16 RJ45 connectors for DCE (modem) connections
6 1 0 - 1 6 _ 3
. 1 6 8 . 1 2 7 . 2
is the CN2600's name
is the CN2600's serial number
is the CN2600's IP address
— 2 —
Button Name
MENU menu activates the main menu, or returns to an upper level
scrolls up through a list of items shown on the LCM
up cursor
panel's second line
down scrolls down through a list of items shown on the
cursor LCM panel's second line
selects the option listed on the LCM panel's second
SEL select
line
The buttons are manipulated in a manner similar to the way a modern
cellular phone operates. As you move through the various functions and
setting options, note that the top line shows the current menu or submenu
name, and the bottom line shows the submenu name or menu item which
is activated by pressing the SEL button.
Refer to CN2600 Dual LAN Console Server User's Manual for more
details.
4. Hardware Installation
1. Installing CN2600
Open the package, and attach CN2600 to a desktop, or fasten it to the
rack cabinet.
2. Wiring Requirements
A. Use separate paths to route wiring for power and devices. If
power wiring and device wiring paths must cross, make sure the
wires are perpendicular at the intersection point.
B. NOTE: Do not run signal or communication wiring and power
wiring in the same wire conduit. To avoid interference, wires
with different signal characteristics should be routed separately.
C. Where necessary, it is strongly advised that you label wiring to
all devices in the system.
3. Connecting Power
AC: Connect CN2600 100-240 VAC power line with its AC
connector. If the power is properly supplied, the "Ready" LED
will show a solid red color until the system is ready, at which
time the "Ready" LED will change to a green color.
If the power is properly supplied, the "Ready" LED will show a solid
red color until the system is ready, at which time the "Ready" LED
will change to a green color.
4. Connecting to the Network
Connect one end of the Ethernet cable to CN2600's 10/100M Ethernet
port and the other end of the cable to the Ethernet network. There are 2
5 4 LED indicators located on the top left and right corners of the Ethernet
connector. If the cable is properly connected, CN2600 will indicate a
valid connection to the Ethernet in the following ways:
The top right corner LED indicator maintains a solid
green color when the cable is properly connected to a
100 Mbps Ethernet network.
The top left corner LED indicator maintains a solid
orange color when the cable is properly connected to
a 10 Mbps Ethernet network.
Action
— 3 —