Starting And Stopping - Bosch AKE 30 S Operating Instructions Manual

F016 L70 495.book Seite 5 Dienstag, 19. Dezember 2006 3:13 15
6. If the chain 9 is overtensioned, slightly turn the
tensioning knob 14 anti-clockwise and re-check
chain tension. Re-adjust chain tension as de-
scribed if necessary.
7. Handtighten locking knob 12
bolt 15..
Lubrication
A B
Important: The chain saw is not supplied
filled with oil. It is essential to fill with oil
before use. Never operate the chain saw
without chain oil or at an empty oil tank level, as
this will result in extensive damage to the prod-
uct.
Chain life and cutting capacity depend on optimum
lubrication. Therefore, the chain is automatically
oiled during operation via the oil outlet 18.
Filling oil tank:
– Set chain saw on any suitable surface with oil filler
cap 4 facing upward.
– Clean area around the oil filler cap 4 with cloth,
unscrew cap.
– Add Bosch biodegradable chain saw oil until res-
ervoir is full.
– Avoid dirt or debris entering oil tank, refit oil filler
cap 4 and tighten.
Important: To allow venting of the oil res-
ervoir,small breather channels are pro-
vided between the oil filler cap, to prevent
leakage ensure machine is left in a horizontal po-
sition (oil filler cap 4 uppermost) when not in
use.
It is important to use only the recommended bi-
odegradable oil to avoid damage to the chain
saw. Never use recycled/old oil. Use of non ap-
proved oil will invalidate the warranty.

Starting and Stopping

Observe the correct mains voltage! The voltage
of the power source must agree with the value given
on the nameplate of the machine. Machines desig-
nated for 230 V can also be operated with 220 V.
Switching On and Off
Hold chain saw as described in "Cutting".
For switching on the machine, press the lock-off
button 3, then fully press the On/Off switch 2 and
hold in this position. The lock-off button 3 can now
be released.
For switching off, release the On/Off switch 2.
Do not stop chain saw after sawing by activating
the front hand guard (kickback brake).
1 • F016 L70 495 • TMS • 19.12.06
Kickback Brake
D
The kickback brake is a safety mechanism acti-
vated through the front hand guard 5, when kickback
on fastening
occurs. Chain stops immediately.
The following function check should be carried out at
regular intervals. Push front hand guard 5 forward
(position
not start. To deactivate the kickback brake, release
On/Off switch 2 and pull hand guard 5 backwards
(position
Cutting
Before Cutting
Before and periodically during cutting check as fol-
lows:
– Is the chain saw in a fail-safe condition?
– Is the oil reservoir filled? Check oil level
B
gauge 25 prior to starting and regularly during op-
eration. Refill oil when oil level is low. The oil tank
filling will last approx. 15 minutes, depending on
sawing intensity and stops.
– Is the chain tension in order and is the chain
sharp? Check chain tension every 10 minutes
during operation. Upon initial operation, new
chains can lengthen considerably. The condition
of the chain influences the the cutting perform-
ance. Only a sharp chain protects from overload.
– Is the kickback brake deactivated and its function
ensured?
– Are you wearing the necessary protective equip-
ment? Wear safety glasses and hearing protec-
tion. Further protective equipment for head, hand,
legs and feet is recommend. Adequate protective
clothing will reduce personal injury by flying de-
bris or accidental contact with saw chain.
Kickback
D
Kickback is the sudden backward/upward motion of
the chain saw, occuring when the chain (at the tip of
the chain bar) comes in contact with a log or wood,
or when the chain becomes jammed.
When kickback occurs the chainsaw reacts unpred-
icably and can cause severe injuries to the operator
or bystanders.
Particular attention must be given when sawing
sidewards, slanted or during length cuts, as the grip-
ping teeth 11 usually can not be applied.
To avoid kickback:
– Saw with the chain bar at a flat angle.
– Never work with a loose, widely stretched or the
heavily worn out chain.
– Ensure chain is sharpened correctly.
English - 5
) and start the chain saw. The chain must
).