Bosch power tools saws & benchtop product manual (52 pages)
Summary of Contents for Bosch AKE 30 S
F016 L70 495.book Seite 1 Dienstag, 19. Dezember 2006 3:13 15 Bedienungsanleitung Operating Instructions Instructions d’emploi Instrucciones de servicio Manual de instruções Istruzioni d’uso Gebruiksaanwijzing AKE 30 S Betjeningsvejledning Bruksanvisning AKE 35 S Brukerveiledningen Käyttöohje Oδηγία χειρισµού AKE 40 S Kullanım kılavuzu...
F016 L70 495 - U2 Seite 2 Mittwoch, 20. Dezember 2006 8:06 08 Robert Bosch GmbH D-70745 Leinfelden Echterdingen 0 600 xxx xxx 230V ~ 50Hz xxx mm x A xxxx W xxxxxxxx 20xx Made in Hungary 24 22 2 • F016 L70 495 • 06.12...
F016 L70 495.book Seite 3 Dienstag, 19. Dezember 2006 3:13 15 3-4 mm 3 • F016 L70 495 • 06.12...
F016 L70 495 - U4 Seite 4 Mittwoch, 20. Dezember 2006 8:08 08 50 mm 50 mm 4 • F016 L70 495 • 06.12...
F016 L70 495.book Seite 1 Dienstag, 19. Dezember 2006 3:13 15 Safety Notes WARNING! Read all safety warnings and all instruc- Do not abuse the cord. Never use the cord for tions. Failure to follow the warnings and instructions carrying, pulling or unplugging the power tool. may result in electric shock, fire and/or serious injury.
F016 L70 495.book Seite 2 Dienstag, 19. Dezember 2006 3:13 15 Store idle power tools out of the reach of children Carry the chain saw by the front handle with the and do not allow persons unfamiliar with the saw chain stopped and the guide bar pointing to power tool or these instructions to operate the the rear.
If the supply cord is damaged, it must be replaced by chain bar in position (do not remove!). a Bosch Service Centre. 4. Turn tensioning knob 14 clockwise until the cor- Products sold in GB only: Your chain saw is fitted rect chain tension is reached.
15 minutes, depending on unscrew cap. sawing intensity and stops. – Add Bosch biodegradable chain saw oil until res- – Is the chain tension in order and is the chain ervoir is full. sharp? Check chain tension every 10 minutes during operation.
Use of the saw to thin out branches or bushes is not – Always the hold chain saw firmly with both hands. approved. – Always use a Bosch low-kickback chain. Length cuts must be carried out with care, as lever- – Apply the metal gripping teeth 11 for leverage.
When the log is supported along its entire length as due to strain, have it exchanged by an authorized illustrated, it is cut from the top (overbuck). Bosch service agent. When the log is supported on one end, as illus- trated, cut 1/3 the diameter from the underside (un- derbuck).
Bosch approved service agent or sharpen the chain using a soft brush and clean cloth. Do not use water, yourself using the Bosch sharpening kit or a Dremel solvents or polishes. Remove all debris, especially power tool with the appropriate grinder (1453), both from the motor cooling vents 26.
F016 L70 495.book Seite 9 Dienstag, 19. Dezember 2006 3:13 15 Fault Finding The following table gives checks and actions that you can perform if your machine does not operate correctly. If these do not identify/remedy the problem, contact your service agent. Warning: Switch off and remove plug from mains before investigating fault.