Advertisement
Product Warranty Information
The Wilbur Curtis Company certifies that its products are free from defects in material and workmanship under normal
use. The following limited warranties and conditions apply:
2 Years, Parts, from Original Date of Purchase on all fittings and tubing.
1 Year, Labor, from Original Date of Purchase on all fittings and tubing.
Stainless Steel components are warranted for two (2) years from date of purchase against leaking or pitting and replacement parts
are warranted for ninety (90) days from date of purchase or for the remainder of the limited warranty period of the equipment in which
the component is installed.
All in-warranty service calls must have prior authorization. For Authorization, call the Technical Support Department at 1-800-995-
0417. Effective date of this policy is April 1, 2003.
Additional conditions may apply. Go to www.wilburcurtis.com to view the full product warranty information.
CONDITIONS & EXCEPTIONS
The warranty covers original equipment at time of purchase only. The Wilbur Curtis Company, Inc., assumes no responsibility for
substitute replacement parts installed on Curtis equipment that have not been purchased from the
Wilbur Curtis Company, Inc. The Wilbur Curtis Company will not accept any responsibility if the following conditions are not met. The
warranty does not cover and is void under the following circumstances:
1) Improper operation of equipment: The equipment must be used for its designed and intended purpose and function.
2) Improper installation of equipment: This equipment must be installed by a professional technician and must comply with
all local electrical, mechanical and plumbing codes.
3) Improper voltage: Equipment must be installed at the voltage stated on the serial plate supplied with this equipment.
4) Improper water supply: This includes, but is not limited to, excessive or low water pressure, and inadequate or fluctuating
water flow rate.
5) Adjustments and cleaning: The resetting of safety thermostats and circuit breakers, programming and temperature adjust-
ments are the responsibility of the equipment owner. The owner is responsible for proper cleaning and regular maintenance
of this equipment.
6) Damaged in transit: Equipment damaged in transit is the responsibility of the freight company and a claim should be made
with the carrier.
7) Abuse or neglect (including failure to periodically clean or remove lime accumulations): The manufacturer is not
responsible for variation in equipment operation due to excessive lime or local water conditions. The equipment must
be maintained according to the manufacturer's recommendations.
8) Replacement of items subject to normal use and wear: This shall include, but is not limited to, light bulbs, shear disks,
"0" rings, gaskets, silicone tube, canister assemblies, whipper chambers and plates, mixing bowls, agitation assemblies and
whipper propellers.
9) Repairs and/or Replacements are subject to our decision that the workmanship or parts were faulty and the defects
showed up under normal use. All labor shall be performed during regular working hours. Overtime charges are the respon-
sibility of the owner. Charges incurred by delays, waiting time, or operating restrictions that hinder the service technician's
ability to perform service is the responsibility of the owner of the equipment. This includes institutional and correctional
facilities. The Wilbur Curtis Company will allow up to 100 miles, round trip, per in-warranty service call.
RETURN MERCHANDISE AUTHORIZATION: All claims under this warranty must be submitted to the Wilbur Curtis Company
Technical Support Department prior to performing any repair work or return of this equipment to the factory. All returned equip-
ment must be repackaged properly in the original carton. No units will be accepted if they are damaged in transit due to improper
packaging. NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA).
RMA NUMBER MUST BE MARKED ON THE CARTON OR SHIPPING LABEL. All in-warranty service calls must be performed
by an authorized service agent. Call the Wilbur Curtis Technical Support Department to find an agent near you.
ECN 14800 . 2/14/13 @ 14.9 . rev C
ECN 14129 . 6/7/12@8.9
WILBUR CURTIS CO., INC.
6913 Acco St., Montebello, CA 90640-5403 USA
Phone: 800/421-6150
Technical Service Phone: 800/995-0417 (M-F 5:30A - 4:00P PST)
Web Site: www.wilburcurtis.com
FOR THE LATEST SPECIFICATION INFORMATION GO TO WWW.WILBURCURTIS.COM
8
Digitally signed by Douglas Webster
DN: cn=Douglas Webster, o=Curtis,
email=dwebster@wilburcurtis.com,
ou=Engrg,
c=US
Date: 2013.02.26 12:16:34 -08'00'
Fax: 323-837-2410
E-Mail: techsupport@wilburcurtis.com
Printed in U.S.A.
2/2013
F-3748 RevC
Advertisement
