Table of Contents
Advertisement
3-WIRE SERVICE CORD OR CONDUIT
4-WIRE SERVICE CORD OR CONDUIT
INSTALLATION
INSTALLATION
1. Insure that the copper ground strap IS CONNECTED
(MOBILE HOMES OR AS REQUIRED BY CODES)
between the middlepost of the main terminal
1. The copper groundstrap connectedbetween the
connectionblockand the range chassis,
neutral (middle)post of the main terminal blockand the
chassisMUST be cut off as shownin figure9. Save the
2. The middle wire of the service cord or ground lead of
green groundscrew to attach the groundfrom the 4
3-wire conduitMUST connectto the neutral (middle)
wire cord. Only a 4 wire cord or conduitshould be
post of the mainterminal block. The othertwo wiresof
used,
the service cordor conduitconnectto the outside
postsof the main terminalconnectionblock. Polarityis
2. The groundwire from the service cordor conduitmust
unimportant,
connect to the range chassis using the green ground
screw.
3. A appropriatestrainrelieffor service cord or conduit
3. The whitewire of the service cordor conduitmust
must be attached to the conduitplate,
connectto the neutral(middle) postof the main
terminal block. The other two wires of the service cord
RED
WHITE_-_
_-
MAIN TERMINAL
,
CONNECTION
BLOCK
or conduit connect to the red and black posts of the
BLACK_
_MIDDLE
WIRE OF
Y
main terminal block, respectively.
SERVICE CORD OR
GROUNO
LEAD
4. An appropriate strain relief for servicecord or conduit
,
or CONDU,
T
must be attached to the conduit plate.
CONVERSION FROM 3-WIRE TO 4-WIRE
GROUND
,,,,_ _,,,,,_/-..-,
,,3
STAMPED
(Model With 3-Wire Service Cord Attached)
RELIF
h_,._,_ f _ ;_Sl
on back of range and removethe 3-wire servicecord from
"_
"r"
( J o.,._,_,,
the mainterminal block. Follow instructions as outlined in
figure 9 to connect the 4-wire service cord.
NOTE: Cord replacement - ONLY a power supply cord
FOR USE W J
rated at 240 volts minimum, 40 amperes or 50 amperes
STAMPED
REMOVE
BRA
CORD
& RE-ATTAC
power supply cord that is marked for use with nominal
MARKED "CO
1 3/8" (34.93 mm) diameter connection opening,with
FIGURE 8
DOWN.
closed loopterminals end marked for use with ranges
ACCEPTABLE 3-WIRE PLUG INSTALLATION
shall be used.
THiS
PORTION
OF----_
/
/
_¢==¢_',_ _
GROUNDING
STRAP
_
/
,IF_D _'I_t_)...
\
.ED\
MusrSERE.VEO --
S ACK\
_
/N
J
_WHITE
WIRE
OF J\
I_
"j_
))//
/
FF_
SERVICE
CORD
\
_
I
///
/
/
j}
oR coN0o,T
\
\\ ////
,/
r
CONDUIT
CHASSIS
(
PLATE
_- _
r
STAMPED
TM
/
GROUND / /_II
._v_/,_._ I /
CONDU_
T
STRAIN _
VlIlk
I
/
•
•
_Jv'-FOR
USE WITH
CONDUIT,
RELIEF
I/_e
_/
REMOVE BRACKET,
FLIP
_r_<
,...
--/
& RE-ATTACH
WITH
HOLE
MARKED 'CONDU I T "
STANPED
-.-./
_
DOWN.
CORD
FIGURE 9
A CCEPTABLE 4- WIRE PLUG INS TALLATION
-7-
Advertisement
Table of Contents
