Lindy 25010 User Manual
  1. Manuals
  2. Brands
  3. Lindy Manuals
  4. Switch
  5. 25010
  6. User manual

Lindy 25010 User Manual

Giga smart switch 24 + 2
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
GIGA Smart Switch 24 + 2
User Manual
English
LINDY No. 25010
www.lindy.com
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (April 2005)

Advertisement

Table of Contents
loading

Related Manuals for Lindy 25010

Summary of Contents for Lindy 25010

  • Page 1 GIGA Smart Switch 24 + 2 User Manual English LINDY No. 25010 www.lindy.com © LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (April 2005)

  • Page 3: Table Of Contents

    Introduction... 4 Start to Manage This Switch... 6 Configuration Functions for the Switch ... 7 Configurations... 8 Port Status ... 8 Port Configuration... 9 About the Copper/Fibre Media Auto-Detection...11 Port Statistics... 12 Port-Based VLAN ... 14 2.5.1 Add Port-Based VLAN Groups ... 15 2.5.2...
  • Page 4 2.11.2.2 Assign a IP address by DHCP server... 50 2.11.3 ARL Aging ... 51 2.12 User Management ... 52 2.13 Reset System ... 53 2.14 Command Line Interface (CLI) ... 54 2.14.1 Hyper Terminal Setup Options... 54 2.14.2 Switch Management Commands In Console... 54 Specifications ... 60...

  • Page 5: Introduction

    IP access from any port and local or remote location. This switch is suitable for enterprise companies or SOHO users who want to build up a high speed network or backbone. With single-mode or multi-mode fibre transceivers you can link remote users or share remote resources.

  • Page 6: Main Features

    Main Features ® Broadcom chipset Non-blocking, full-line speed, store-and-forward operation Supports normal Ethernet frames and jumbo frames from 64 bytes to 9216 bytes Auto-negotiation and auto-MDIX on all 10/100/1000M copper ports 24 x 10/100/1000 RJ-45 ports with copper ports, 2 are shared with mini-GBIC Auto-detection for copper/fibre media link on 2 combo ports 512 K bytes packet buffer 8K MAC entries, 4K VLAN entries...

  • Page 7: Start To Manage This Switch

    Network mask: 255.255.248.0 Default gateway:192.168.223.254 Try to use the default IP shown above to PING the switch from your PC to make sure the network connection is successful. The default IP address on this switch can be modified later for your needs.

  • Page 8: Configuration Functions For The Switch

    1.2 Configuration Functions for the Switch After the login is successfully validated, the switch’s home page – System page will show up. The left part on the page provides the function menus (shown as below) to activate to the individual configuration page.

  • Page 9: Configurations

    This page provides the following information: Port – to specify a port on the switch Link Status – to show the port link status: Up / Down Speed / Duplex – to show the current link speed (1G / 100M / 10M bps) and duplex mode (Full / Half) while the port is linkup.

  • Page 10: Port Configuration

    2.2 Port Configuration If you need to do the port configuration, just select the desired port by clicking the Port number in the Port Status page. Then the Port Configuration page (shown as below) for the selected port will be opened: The following parameters will be provided and configured in the Port Configuration page: Port –...
  • Page 11 After the desired options are selected for the above functions, click the Apply button to save the current settings to the switch and go back to the Port Status Page. Click the Cancel button to go back to Port Status page.

  • Page 12: About The Copper/Fibre Media Auto-Detection

    2.3 About the Copper/Fibre Media Auto-Detection This switch provides an option to use either copper or fibre media for the first two combo ports - Port1 and Port2. This means that you can setup the link by using either copper media to plug-in to the copper port or use fibre media to plug-in the mini-GBIC port.

  • Page 13: Port Statistics

    2.4 Port Statistics The Port Statistics function lets you see the TX/RX packets through each port. The Clear Counters button will clear all packet counters to 0. The Refresh button will get port statistics again. You can check each ports statistics more precisely. Just click the Port number to see the detailed information.
  • Page 14 The table shown below has the description for each column. UnicastPkts Number of good unicast packets transmitted. MulticastPkts Number of good multicast packets transmitted. Number of good broadcast packets transmitted. BroadcastPkts Single Collision Number of packets in which the transmission experienced one collision Number of packets in which the transmission experienced over two collisions Multi Collisions 64 BytePkts...

  • Page 15: Port-Based Vlan

    2.5 Port-Based VLAN The port-based VLAN divides the ports into different Virtual LAN domain groups. After setting the port-based VLAN, the different VLAN groups can’t access each other. The VLAN initial setting page is shown as below: You need to click the Enable/Disable link text to enable/disable the port-based VLAN. When port-based VLAN is enabled, the 802.1Q VLAN will be disabled automatically.

  • Page 16: Add Port-Based Vlan Groups

    2.5.1 Add Port-Based VLAN Groups To add a port-based VLAN group, select the Create New VLAN in the VLAN NO dropdown of the Port-Based VLAN page shown as below: After selecting the Create New VLAN, the page will be changed like this: In the above page, VLAN NO will auto setup.
  • Page 17 Below is the example page when the user sets Port1-12 to the VLAN Group2 after clicking the Create button. Now there is a VLAN group No.2 created with the member Port1-12. While the group No.2 is created, all the members in group No.1 are removed to operate the VLAN function.

  • Page 18: Delete Port-Based Vlan Groups

    2.5.2 Delete Port-Based VLAN Groups To delete a port-based VLAN group, just select a desired group (e.g. No.2) to be removed and click the Remove This VLAN button. Pressing the Remove This VLAN button results in the following: Now all ports are set to the members in VLAN group No.1.

  • Page 19: Edit Port-Based Vlan Groups

    2.5.3 Edit Port-Based VLAN Groups To edit the current port-based VLAN group, first select the group (e.g. group No. 3) you want to edit (to add Port7 & Port8 as members) and click the Apply button to activate the setting. The following figure shows the configuration for the selected group (e.g.

  • Page 20: 802.1Q Vlan

    (Command Line Interface) to recover. The detailed CLI operating guide will be discussed in section 2.14. Here is a simple way to recover the web access to the switch. 1. In CLI, type VE to disable 802.1Q VLAN 2. Go to 802.1Q VLAN web interface. Set the default VLAN ID 1 group member(01-24) to U 3.

  • Page 21: Enable/Disable Vlan

    2.6.1 Enable/Disable VLAN In the 802.1Q VLAN page you can enable/disable the tag-based VLAN function by clicking (Enable) or (Disable) besides the page header: Enable – to activate the tag-based VLAN function (port-based VLAN function will automatically be disabled). Disable – to de-activate the tag-based VLAN function, even though there are some VLAN entries created.

  • Page 22: 802.1Q Vlan Port Configuration

    UnTag Frame – Accept or drop incoming untag frames. Tag Frame – Accept or drop incoming tag frames. Finally, there are 2 buttons to select: Apply: To submit the port configuration settings to the switch. Back: To go back to the 802.1q main setting page.

  • Page 23: 802.1Q Vlan Config

    Input the VID (1-4094) and check the member row to select the ports which belong to this VLAN group. After these settings are complete click the Create button to submit the data to the switch. Click the Cancel button to abort the actions and go back to the VLAN Config page.
  • Page 24 Here is an example of how to configure the 802.1q VLAN. There are four existing 802.1q VLAN entries as shown below. You can delete the 802.1q VLAN entry. Click a radio button on the Select column to select the entry to be deleted (e.g.
  • Page 25 If you would like to edit the parameters of an 802.1q VLAN, just select a VID to be changed (e.g. VID =300) then click the Apply button to do the modifications: Port 17 and Port18 are selected to be the tag members of this group. Finally, click the Apply button to do the changes.

  • Page 26: Trunk

    The 24G web smart switch provides dynamic failover when trunking is enabled. If a port in the trunk group fails, the other ports of the trunk group assume traffic designated automatically for the trunk.
  • Page 27 Because a trunk port can be aggregated by the member ports with the same configurations in most functions for each other, there are some rules to limit the configurations of the trunking. The following section will list the related rules for this function.

  • Page 28: Trunking Rules

    2.7.1 Trunking Rules The following rules will limit the configurations for port trunking: The attributes of all trunk member ports in Port Configuration, Mirror, Rate Control, 802.1Q VLAN and Port-Based VLAN functions must be the same. All trunk member ports can not be a capture port or monitored port in Mirror function. If Port1/Port2 using the fibre media wants to be grouped with the ports using pure copper (Port3 –...
  • Page 29 When the enabled trunk group is set to disabled, all trunk member ports will be released to ordinary ports and their functions can be configured individually. At that moment, their configuration attributes will be retained to the last settings while they were member ports of the trunk group.

  • Page 30: Get/Refresh The Latest Trunk Settings

    2.7.2 Get/Refresh the Latest Trunk Settings Click the Trunk menu on the web page, the latest trunk settings on the switch will be displayed. This is also the page to configure the trunk function.

  • Page 31: Enable Trunk

    2.7.3 Enable Trunk Step 1: Choose the Distribution Criterion. Step 2: Choose the member port(s) up to 8 ports for each trunk group. Step 3: Click the Apply button to enable trunk settings.

  • Page 32: Modify Trunk Settings

    2.7.4 Modify Trunk Settings Step 1: Choose the Distribution Criterion. Step 2: Choose the member port(s) up to 8 ports for each trunk group. Step 3: Click the Apply button to modify trunk settings.

  • Page 33: Disable Trunk

    2.7.5 Disable Trunk Step 1: Click the Not Trunking. Step 2: Click the Apply button to disable trunk.

  • Page 34: Port Mirroring

    Port mirroring allows ingress and/or egress traffic to be monitored by a single port. The single port is mirror capture port. The 24G web smart switch can be configured to mirror the ingress and/or egress traffic of another port. Port monitoring is independent of L2 switching. The networking manager can monitor all traffic sent/received through the 24G web smart switch.

  • Page 35: Get/Refresh The Latest Mirror Settings

    2.8.1 Get/Refresh the Latest Mirror Settings Click the Mirror menu on the web page. The mirror settings on the switch will be displayed. This is also the page to configure the port mirroring function. The following parameters are required to be set: Mirroring Options –...

  • Page 36: Enable Mirror

    2.8.2 Enable Mirror Step 1: Choose Mirror option to be Mirror All Frames. Step 2: Choose the Monitored Port to be Port16. Step 3: Choose the Capture Port to be Port8. Step 4: Click the Apply button to enable mirroring settings.

  • Page 37: Modify Mirror Settings

    2.8.3 Modify Mirror Settings Step 1: Change Mirror option to be Mirror Outgoing Frames. Step 2: Change the Monitored Port to be Port3 Step 3: Change the Capture Port to be Port22. Step 4: Click the Apply button to modify mirroring settings.

  • Page 38: Disable Mirror

    2.8.4 Disable Mirror Step 1: Choose Mirror option to be Disable Mirror. Step 2: Click the Apply button to disable mirroring.

  • Page 39: Qos (Quality Of Service)

    Default Priority in the Port Config page to assign the packet to one of four transmit queues. If the incoming packet is tagged or priority tagged, the 24G web smart switch uses the priority field in the incoming packet tag to assign the packet to one of four transmit queues.

  • Page 40: Get/Refresh The Latest Qos Settings

    2.9.1 Get/Refresh the Latest QOS Settings Click the QOS menu on the web page. The QOS settings on the switch will be displayed. This is also the page to configure QOS. The following parameters are provided to be set: Scheduling Method Strict Priority –...

  • Page 41: Enable Qos

    2.9.2 Enable QOS Step 1: Choose the Scheduling Method (ex: Weighted Round Robin). Step 2: Set Priority/Queue map (ex: Priority1, 2, 3 and 4 belong to Queue0, Priority4 and 5 belong to Queue1, Priority6 belong to Queue2, Priority7 belong to Queue4). Step 3: If Scheduling Method is Weighted Round Robin, assign a weight for every transmit queue (ex: Queue0 weight = 1, Queue1 weight = 3, Queue2 weight = 5, Queue3 weight = 7).

  • Page 42: Modify Qos Settings

    2.9.3 Modify QOS Settings Step 1: Change the Scheduling Method to be Strict Priority. Step 2: Change the Priority/Queue map (ex: Prirotiy0 belong to Queue3, Priority1, 2 and 3 belong to Queue2, Priority4, 5 and 6 belong to Queue1, and Priority7 belongs to Queue0). Step 3: Click the Apply button to modify QOS settings.

  • Page 43: Rate And Storm Control

    2.10 Rate and Storm Control To provide more efficient system performance, the 24G web smart switch provides rate and storm control to limit the per-port traffic rate and to globally suppress the storm from unknown or broadcast frames received by the system.
  • Page 44 Select port number to setup the per-port rate control value. In the page of ingress rate limit, shown in the following figure (e.g. for Port2), select one (e.g. 8Mbps) of 14 different rates to limit the rate or select “No Limit” to un-limit the rate for this port. After clicking the Apply button to activate the setting, the previous page will be reappear and show the latest setting.

  • Page 45: Storm Control

    2.10.2 Storm Control In the Rate Limit and Storm Control page, the hyperlink (e.g. Disabled) on the row with Storm Control field shows the current setting of this function. This function will globally affect all ports in the system. Just click this hyperlink to configure the setting. In the Storm Control page, there are 2 fields to configure this function: Storm Control Type –...
  • Page 46 Storm Control Rate – this field provides 13 different control rates from 1fps (frames per second) to 15,000fps. This dropdown will be disabled while the Storm Control Type is disabled. After selecting the storm control type and rate, click the Apply button to activate the settings for this function.

  • Page 47: System Setup

    2.11 System Setup The System Setup page provides the management information of the switch. This page, shown as below, can be activated by clicking the System Setup menu under the System section. The following parameters can be configured / displayed: Model Name –...

  • Page 48: Firmware Update

    This system supports both BOOTP/TFTP and pure TFTP to update the firmware. The TFTP server IP address and firmware filename needs to be correctly provided to the switch to start the firmware updating if the pure TFTP way, is selected. Using the BOOTP/TFTP it is much easier to do the firmware updating because no parameters need to be input if the BOOTP/TFTP server is correctly setup.

  • Page 49: Firmware Update Via Tftp

    Click the Apply button to start the firmware update through the any front port on the switch. The time taken for processing the firmware update will be approximately 50 seconds. NOTE: If the switch can not connect to the TFTP server, click the Cancel button to stop the firmware update process.

  • Page 50: Firmware Update Via Bootp/Tftp

    Before proceeding with the firmware update, it is required to correctly prepare the BOOTP/TFTP server and the firmware file which will be uploaded to the switch. (Please refer to the vendor’s instruction guide for setting up the TFTP server you would like to use).

  • Page 51: Dhcp Client

    2.11.2 DHCP Client The IP address of the 24G web smart switch can be statically assigned by manual entry or dynamically assigned by a DHCP server. 2.11.2.1 Assign a fixed IP address Change DHCP Client to be disabled. Enter a fixed IP address, Subnet mask and Gateway, and then click the Apply button.

  • Page 52: Arl Aging

    2.11.3 ARL Aging The 24G web smart switch supports aging timer for MAC address entry in the address table. If ARL aging is enabled and aging time is 300 seconds, every MAC address entry learned from every front port will stay in the address table for 300 seconds. After 300 seconds, the switch will remove this MAC entry.

  • Page 53: User Management

    User management is used for maintaining the username and password for login validation to access the switch. This switch provides one login account for configuration management. Just click the User Management menu to activate the User Management page as shown below: New Username –...

  • Page 54: Reset System

    MAC address won’t be changed) to default settings before rebooting the system. This means that any customized configurations will be lost and can’t be recovered. The 24G web smart switch also provides an alternative to the Reset System option by using the Reset button on the rear panel:...

  • Page 55: Command Line Interface (Cli)

    In addition to the web management, the 24G web smart switch also provides a serial interface (RS-232) as a console port on the rear panel to manage the switch for system setup, user management, reset system and firmware updates through the command line interface (CLI). We recommend you use Windows Hyper Terminal.

  • Page 56: Help Menu

    Help Menu Press “H”, “h” or “?” to show all management commands in the console. Get System Information Press “IG” or “ig” to show model name and firmware version. Get Current Network Settings Press “NG” or “ng” to show DHCP client status, system IP address, network mask, gateway and MAC address.
  • Page 57 Configure Network Press “NS” or “ns” to configure system network. If the user wants to assign this system an IP address by DHCP server, enter “Y” or “y” to start DHCP progress. . If the user wants to assign this system a fixed IP address manually, please enter “N” or “n” to abort DHCP progress.

  • Page 58: Set Pvid

    (port 25) in 802.1Q VLAN function also can be modified. The PVID which the user wants to set must be one of the existing VLAN group ID. The Admin port is the port you use to manage the switch function. The Default Admin PVID is 1.

  • Page 59: Reboot System

    Choose “1” to update firmware via TFTP. Enter the TFTP server IP address and firmware filename. Choose “2” to update the firmware via BOOTP/TFTP. Once the 24G web smart switch has rebooted, the firmware upgrade progress has finished correctly. Type “IG” or “ig” to check the firmware version after login. Reboot System...
  • Page 60 Reboot System After Write Default Type “RD” or “rd” to reset the system to factory settings. Logout Type “LO” or “lo” to logout of the system.

  • Page 61: Specifications

    3 Specifications Standards Compliance IEEE 802.3 10BaseT Ethernet IEEE 802.3u 100BaseTX Fast Ethernet IEEE 802.3ab 1000Base Gigabit Ethernet IEEE 802.3x flow control for half and full duplex IEEE 802.1q Tag-based VLAN Interfaces 24 x 1000BaseTX RJ-45 connector ports, 2 mini-GBIC ports 1 RS-232 terminal port Buffer Memory 512MB for packet buffers...
  • Page 62 Power Input: 100-240VAC, 50/60Hz Power consumption: 40 Watts max. Dimensions 440mm (W) × 184mm (D) × 44mm (H) Weight 2.3 Kg Electromagnetic Emissions: Class A FCC, CE, VCCI, C-Tick Safety...

  • Page 63: Fcc Warning

    • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced technician for help LINDY No. 25010 www.lindy.com...

Table of Contents