Precautions On Adjusting - Sony DCR-TRV940 Adjustment Manual

3-1-2.

Precautions on Adjusting

1) This set is adjusted in two modes, VTR mode and CAMERA
mode.
To activate the VTR mode, set the POWER switch to the
"VIDEO" position, or select the "Forced VTR Power ON
Mode" with the adjusting remote commander. (Note 1)
To activate the CAMERA mode, set the POWER switch to the
"CAMERA" position, or select the "Forced CAMERA Power
ON Mode" with the adjusting remote commander. (Note 2)
After the adjustment finished, be sure to cancel the "Forced
VTR Power ON Mode" or "Forced CAMERA Power ON
Mode". (Note 4)
2) The VTR can be operated even if the cabinet (R) (operation
switch (CK-116 board), LCD block) is removed. However, the
lithium 3V power is removed if the cabinet (R) is removed
(CN5203 on the CK-116 board is disconnected), causing the
data such as date and time, user set menu, etc. to be cleared.
These data must be re-set after the adjustment finished. The
diagnostic data and log data (drum running hours, user first
power ON date, last dew date) are saved even if the lithium 3V
power is removed. When the cabinet (R) is removed, discon-
nect the following connector:
1. CK-116 board CN5203 (60P, 0.5mm)
3) The VTR can be operated even if the front panel block (MA-
410 board, focus ring, micro unit) is removed. When the front
panel block is removed, disconnect the following connectors:
1. MA-410 board CN5906 (33P, 0.5mm)
2. MA-410 board CN5904 (8P, 0.5mm)
4) The BT-003 board (DCR-TRV950/TRV950E only) and the
flash unit need not be connected. If removed, disconnect the
following connectors:
1. BT-003 board CN101 (15P, 0.3mm) (DCR-TRV950/
TRV950E only)
2. BT-003 board CN102 (Bluetooth antenna terminal)
(DCR-TRV950/TRV950E only)
3. DB-014 board CN1010 (23P, 0.3mm)
5) The view finder block (LB-080 board) and the intelligent ac-
cessory shoe need not be connected. If removed, disconnect
the following connectors:
1. DB-014 board CN7211 (21P, 0.3mm)
2. DB-014 board CN7205 (27P, 0.3mm)
6) The lens block (CD-389 board) need not be connected. If re-
moved, disconnect the following connectors:
1. VC-288 board CN1201 (60P, 0.5mm)
2. DB-014 board CN1501 (10P, 0.5mm)
3. DB-014 board CN1004 (39P, 0.3mm)
7) With the "forced power ON mode" activated, the VTR can be
operated even if the operation switch block (PS-1870) is re-
moved. If removed, disconnect the following connector:
1. DB-014 board CN7201 (6P, 0.5mm)
DCR-TRV940/TRV940E/TRV950/TRV950E
Note 1: Setting the "Forced VTR Power ON" mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press
the PAUSE button of the adjustment remote com-
mander.
The above procedure will enable the VTR power to
be turned on with the power switch (PS-1870 block)
removed.
After completing adjustments, be sure to exit the
"Forced VTR Power ON mode".
Note 2: Setting the "Forced Camera Power ON" mode (Camera
mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press
the PAUSE button of the adjustment remote com-
mander.
The above procedure will enable the camera power
to be turned on with the power switch (PS-1870
block) removed.
After completing adjustments, be sure to exit the
"Forced Camera Power ON mode".
Note 3: Setting the "Forced Memory Power ON" mode (Memory
mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press
the PAUSE button of the adjustment remote com-
mander.
The above procedure will enable the memory power
to be turned on with the power switch (PS-1870
block) removed.
After completing adjustments, be sure to exit the
"Forced Memory Power ON mode".
Note 4: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press
the PAUSE button of the adjustment remote com-
mander.
3) Select page: 0, address: 01, and set data: 00.
6-51