Initialization Of E, F, 1E, 1F Page Data; Modification Of E, F, 1E, 1F Page Data - Sony DCR-TRV940 Adjustment Manual

1-2-3.

Initialization of E, F, 1E, 1F Page Data

Note: If reading/writing data on pages 1E, 1F, set data: 01 to
page: 0, address: 10, and then select pages E, F. By this
data setting, the pages 1E, 1F can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to "00".
1. Initializing of E, F, 1E, 1F Page Data
Note 1: If "Initialization of Pages E, F, 1E, 1F" is executed, all
data on pages E, F, 1E, 1F are initialized. (Only an indi-
vidual page cannot be initialized)
Note 2: If the E, F, 1E, 1F page data has been initialized, the
following adjustments need to be performed again.

1) Modification of E, F, 1E, 1F page data

2) Camera system adjustments
Note 3: Check that the voltage of power supply is 6.0 ± 0.1Vdc.
Note 4: NTSC model: DCR-TRV940/TRV950
PAL model: DCR-TRV940E/TRV950E
Adjustment Page E
Adjustment Address 00 to FF
Adjustment Page F
Adjustment Address 10 to FF
Adjustment Page 1E
Adjustment Address 00 to C3
Adjustment Page 1F
Adjustment Address 00 to FF
Initializing method:
Order Page Address Data
1 0 01 01
2 0 10 00
3 6 01
4 6 03 01
5 6 02
6
Procedure
Set the following data, and
press PAUSE button.
2D: NTSC model
2F: PAL model
Press PAUSE button.
Check the data changes to
"01".
Perform "Modification of E,
F, 1E, 1F Page Data"
DCR-TRV940/TRV940E/TRV950/TRV950E
2. Modification of E, F, 1E, 1F Page Data
If the E, F, 1E, 1F page data has been initialized, change the data
of the "Fixed data-2" address shown in the following table by
manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages E, F, set data: 01 to page: 0,
address: 00, and then select pages E, F.
3) If modification of data on pages 1E, 1F, set data: 01 to page: 0,
address: 10, and then select pages E, F. After the modification
of data finished, return the data on page: 0, address: 10 to "00".
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the
camcorder may not operate.
5) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification E, F, 1E, 1F page
data:
Order Page Address Data
1 0 10
2 2 00
3 2 01
4
6-15
Procedure
00
29
29 Press PAUSE button.
Perform "66MHz/54MHz
Origin Oscillation Adjust-
ment" of "CAMERA
SYSTEM ADJUSTMENTS"