Heat&Glo HE36CLX-S Owner's Manual

Installation and operation
Hide thumbs Also See for HE36CLX-S:
Table of Contents

Advertisement

Quick Links

Model: HE36CLX-S
HE36CLXLP-S
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14
Owner's Manual
Installation and Operation
• Leave this manual with
party responsible for use
and operation.
WARNING
DO NOT TOUCH GLASS
NEVER ALLOW CHILDREN
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
Installation and service of this appliance should be performed by a
Hearth & Home Technologies factory-trained Energy Pro technician.
HOT GLASS WILL
CAUSE BURNS.
UNTIL COOLED.
TO TOUCH GLASS.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HE36CLX-S and is the answer not in the manual?

Questions and answers

Summary of Contents for Heat&Glo HE36CLX-S

  • Page 1 NFI gas supplier. certifi ed professional. Installation and service of this appliance should be performed by a Hearth & Home Technologies factory-trained Energy Pro technician. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 2: Congratulations

    BTUH: 00,000 00,000 00,000 00,000 MIN. MIN. INPUT INPUT BTUH: BTUH: 00,000 00,000 00,000 00,000 Serial Serial ORIFICE ORIFICE SIZE: SIZE: #XXXXX #XXXXX #XXXXX #XXXXX XXXXXXXX XXXXXXXX (Serie): (Serie): Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 3: Table Of Contents

    G. Convection Blower Safety Switch....42 A. Vent Termination Minimum Clearances ....21 Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 4 C. Contact Information ......59  = Contains updated information. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 5: Limited Lifetime Warranty

    3 years Firebox and heat exchanger Lifetime All replacement parts 90 Days beyond warranty period See conditions, exclusions, and limitations on next page. 4021-645F 02-18-13 Page 1 of 2 Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 6 THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE. 4021-645F 02-18-13 Page 2 of 2 Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 7: Listing And Code Approvals

    CANADA 34,000 (2000-4500 FT) when it is installed in locations such as in bathrooms or near sinks. 36,000 (0-2000 FT) HE36CLXLP-S(LP) CANADA 33,000 (2000-4500 FT) Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 8: Requirements For The Commonwealth Of Massachusetts

    VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB- of the installation. STRUCTIONS”. See Gas Connection section for additional Common- wealth of Massachusetts requirements. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 9: User Guide

    SECTION 2.D FIXED GLASS ASSEMBLY (NOT SHOWN) SECTION 16.F MANTEL SECTION 5.D, 15.B HEARTH CLEAR SPACE SECTION 2.C FILTERED RETURN AIR DUCT SECTION 9.C Figure 2.1 General Operating Parts Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 10: Clear Space

    WARNING! Risk of Fire or Asphyxiation! DO NOT op- your decorative door or front. erate fi replace with fi xed glass assembly removed. E. Fixed Glass Assembly See Section 16.F. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 11: Lighting Instructions (Dsi)

    For additional information on operating your Hearth & Home Technologies fi replace, please refer to www.fi reside.com. Final Inspection by _________________________________ 2183-913 Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 12: After Fireplace Is Lit

    • Some people may be sensitive to smoke and odors. MEASUREMENTS FROM TOP EDGE OF THE OPENING • Smoke detectors may activate. SEE DETAIL A APPLIANCE FRONT Figure 2.3. Maximum Wall Surface Temperatures Above Fireplace Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 13: Frequently Asked Questions

    Electronic Ignition Module (EIM). 3. Refer to RedLINK instruc- tions regarding connections. Thermostat Check batteries. Batteries dead. Replace batteries. screen is blank. Batteries ok. Call qualifi ed service technician. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 14: Maintenance And Service

    Hold glass in place with one hand and secure glass work surface. latches with the other hand. • Inspect gasket seal and its condition. • Reinstall door or decorative front. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 15: Burner Ignition And Operation

    Polish with fi ne steel wool or replace as required. • Remove all foreign objects. • Verify unobstructed air circulation. • Verify unobstructed ducts and fi lter. • Check for evidence of water/condensate leakage. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 16: Installer Guide

    (SECTION 2.F) FILTERED RETURN AIR DUCT SECTION 9.C CONDENSATE MANTEL AND REMOVAL MANTEL LEG (SECTION 11 ) (SECTION 5.D ) SURROUND GAS LINE (SECTION 11) Figure 4.1 Typical System Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 17: Design And Installation Considerations

    1/2 - 3/4 in. length, #6 or #8 Self-drilling screws Caulking material (300ºF minimum continuous exposure rating) 1/4 NPT barbed hose fi tting (for checking gas pressures at valve) Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 18: Framing And Clearances

    Due to high temperatures, the appliance should be locat- ed out of traffi c and away from furniture and draperies. Inches 97-1/2 See Section D. Mantel Projections Millimeters 1753 1067 2477 Figure 5.1 Appliance Locations Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 19: Constructing The Appliance Chase

    Appliance Drain Center (Vent Pipe) (Height) (Depth) (Width) Inches 4-1/2 Millimeters 1118 1067 1245 * Adjust framing dimensions for interior sheathing (such as sheetrock) Figure 5.2 Clearances to Combustibles Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 20: Mantel And Wall Projections

    NOT the top of the fi replace. Figure 5.5 Clearances to Mantel Legs or Wall Projections Figure 5.4 Minimum Vertical and Maximum Horizontal (Acceptable on both sides of opening.) Dimensions of Combustibles Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 21: Termination Locations

    Over 16/12 to 18/12 ..........7.0 Over 18/12 to 20/12 ..........7.5 Over 20/12 to 21/12 ..........8.0 * 3 foot minimum in snow regions Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 22 • Vinyl protection kits are suggested for use with vinyl siding. Figure 6.3 Minimum Clearances for Termination Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 23: Vent Information And Diagrams

    8-1/2 in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 7.1). Figure 7.2 DVP Pipe Effective Length Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 24 Condensate backup may lead to property damage. Horizontal or Vertical Termination TOTAL VENTING LENGTH (feet) # of 90º Elbows Figure 7.3 NOTE: A 90º elbow may be replaced with two 45º elbows. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 25: Vent Clearances And Framing

    Whenever a non-combustible wall is penetrated, the fi restop is only required on one side and no heat shield is necessary. 4 in. 4 in. 47 IN. Figure 8.1 Wall Penetration Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 26: Install The Ceiling Firestop

    Figure 8.2 Installing Ceiling Firestop INSTALL ATTIC INSULATION SHIELDS BEFORE OR AFTER INSTALLATION OF VENT SYSTEM CEILING FIRESTOP CEILING FIRESTOP INSTALLED BELOW CEILING INSTALLED ABOVE CEILING Figure 8.3 Installing the Attic Shield Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 27: Appliance Preparation

    • Appliance should be secured to a fl ooring structure that is a minimum of 3/4 inch thick. • For surfaces other than wood, anchors should be used. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 28: Heat Ducting Installation

    Max length of duct run = 34 ft. • For optimum appliance performance, Hearth & Home Technologies suggests using rigid ducting. Figure 9.3 Filter Replacement HEAT DUCT KNOCKOUTS Figure 9.2 Heat Duct Knockouts Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 29: Installing Vent Pipe

    fl ues of the slip section can be cut to the desired length. • All unit collar, pipe, slip section, elbow and cap outer fl ues shall be sealed with foil tape or high temperature silicone (300ºF minimum continuous exposure rating). Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 30: Secure The Vent Sections

    DO NOT allow vent to sag below connection point to appliance. Figure 10.7 Securing Horizontal Pipe Sections 120º Figure 10.5 Securing Vertical Pipe Sections 120º Figure 10.6 Securing Horizontal Pipe Sections Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 31: Vertical Termination

    Sheet metal edges are sharp. 1. Slide plastic storm collar over metal roof fl ashing. Collar can be rotated 180º to accommodate various roof pitches. Figure 10.11 Vent Flange Installed on Storm Collar Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 32 STORM COLLAR STORM COLLAR Figure 10.12 Caulk Flange Storm Collar Overlap VERTICAL TERMINATION FLASHING COLLAR Figure 10.14 Correct Vertical Termination Installation FLASHING ROOF CLAMP Figure 10.13 Vertical Termination Installation. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 33: Install Horizontal Termination Cap (Cvp-Hck)

    CVP-HCK can adjust 9 inches (14 in. to 23 in.). SLOTS ON BOTTOM SIDE OF CAP. NOTICE: When installing the horizontal termination cap, ensure the slots are on the bottom of the cap. Figure 10.15 CVP-HCK Orientation Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 34: Condensate Removal System

    TUBE CONDENSATE PUMP ACCESS CONDENSATE PANEL DRAIN 1/2 IN. PVC FITTING 4-1/2 IN. Figure 11.2 Upper Inducer Housing Tube - Connected to Inducer Figure 11.1 Condensate Removal Access Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 35 See Section 16.D and 16.E. 9. Reconnect electrical supply. 10. Turn on gas supply at valve. Figure 11.3. Upper Inducer Housing Tube Connected to Field- Supplied Funnel Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 36: Control Module Sequence Of Operation

    fl ash during the auto reset delay before reset from the thermostat call for heat is removed, the control de-en- soft lockout. ergizes the gas valve and begins post-purge and blower Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 37 See Service Technician’s Manual for Control Module curs during call for fan, the circulating fan is de-energized Troubleshooting. and a normal heating sequence will occur. A call for fan is ignored while in soft lockout. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 38: Gas Information

    1/2 in. (13 mm) T-handle manual shut-off valve and fl exible gas connector are connected to the 1/2 in. (13 mm) control valve inlet. • If substituting for these components, please consult local codes for compliance. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 39: High Altitude Installations

    OUTLET MANIFOLD OUTLET MANIFOLD PRESSURE TAP PRESSURE TAP Figure 13.1 Location of Gas Ball Valve 5/8-18 UNF FLARE FITTING Figure 13.2 Location of Gas Line Access Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 40: Electrical Information

    WARNING! Risk of Shock! Replace damaged wire with connection when servicing controls. Wiring errors can type 105º C rated wire. Wire must have high temperature cause improper and dangerous operation. Verify proper insulation. operation after servicing. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 41 Main gas valve output Pressure switch input Pressure switch output (common with pin 3) Flame sense output Limit switch output Flame sense/chassis ground (24VAC common) Figure 14.2 Appliance Wiring Diagram Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 42: Junction Box Installation

    CAPACITOR SWITCH Figure 14.3 Exhaust Safety Switch NOTICE: DO NOT wire 110- 120 VAC to Equipment Interface Module. Figure 14.6 Capacitor and Safety Switch Figure 14.4 Junction Box Detail Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 43: Finishing

    Figure 15.1 Location of Gas Shutoff Knob Step 2. Disconnect the power cord from the junction box. Figure 15.4 Splatter Guard Openings JUNCTION Figure 15.2 Location of Junction Box Figure 15.5 Splatter Guard Installation Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 44 Figure 15.6 Splatter Guard Installed To Remove the Splatter Guard: Grab splatter guard at the bottom with both hands and pull outward as shown in Figure 15.7. Figure 15.7 Removing Splatter Guard Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 45: Mantel And Wall Projections

    2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16 Inches Millimeters  Inches  Millimeters Figure 15.9 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.) Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 46: Doors

    Finishing materials 1 in. maximum thick. Stop fi nishing material fl ush with opening. Figure 15.10 Overlap Fit Door (Includes 1/8 in. opening each side of door) Figure 15.11 Inside Fit Door Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 47: Appliance Setup

    fl oor or hearth. SUPPORT WHEEL ASSEMBLY NUTS STOWED SUPPORT WHEEL DEPLOYED SUPPORT WHEEL FIREBOX LATCHES Figure 16.1 Disengage Firebox from Outer Shell Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 48: Fixed Glass Assembly

    Pull gently on the fi rebox to verify the fi rebox is correctly secured and latched. 1/4 TURN LATCHING FASTENERS 1/4 INCH NUTS Figure 16.2 Door Latching Fasteners Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 49: Refractory

    See Figure 2. Ensure side panels contact back panel so that no gaps exist. Fol- low the same procedure to place the right side refrac- tory panel. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 50 Panels will fi t fl ush with the bottom of the fi rebox. See Figure 5. Figure 5. Left and Right Base Refractory Installed 2183-936 Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 51: Teco-Sil Placement

    • Fog the Teco-Sil to create a realistic coal bed appear- ance. NOT PAINTED NOT PAINTED Figure 16.5 Teco-Sil Not Painted TOO LIGHT TOO LIGHT Figure 16.6 Teco-Sil Too Light Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 52: Ember Placement

    LOCATING HOLES FIBER BURNER TOP Figure 16.10 Embers Overlapping Burner Port Holes (LP only). PILOT COVER BURNER SHIELD BURNER ASSEMBLY GUIDE SLEEVES Figure 16.8 Place Fiber Burner Top on Pins Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 53: Install The Log Assembly

    fi tted together, mate the groove located on the bottom of Log #2 with the horizontal grate bar and slide Log # 2 toward the left until it rests against the far left grate tine. See Figure 7. Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 54 FLAT FLAT AREA AREA LOCATING LOCATING NOTCH NOTCH LOG CONTACTS GRATE TINES LOG CONTACTS GRATE TINES LOG CONTACTS GRATE TINE LOG CONTACTS GRATE TINE Figure 12 Figure 11 2183-935C Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 55: Air Shutter Setting

    Short cycling may occur. SCREW Figure 16.11 Air Shutter Air Shutter Settings HE36CLX-S 3/8 IN. Full Open Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 56: Reference Materials

    Appliance Dimensions Table Location Inches Millimeters Location Inches Millimeters 35-11/16 20-1/2 36-7/8 27-1/2 40-15/16 1039 1041 43-11/16 1109 15-7/16 4-1/2 8-7/16 13-5/16 34-7/16 3-5/16 27-1/2 11-7/16 3-1/2 Figure 17.1 Appliance Dimensions Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 57: Vent Components Diagrams

    5/16 in. 8 mm 8 mm Ø=2.4 in. Ø=2.4 in. 61 mm 61 mm CVP36 CVP60 CVP12A 36 Inch Pipe 60 Inch Pipe Adjustable Assembly Figure 17.2 CVP Pipe Components Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 58 Trim Ring Inner CVP-RF12 7-12 Pitch Roof Flashing CVP-HCK Horizontal Termination CVP-FS Firestop CVP-TRI (INTERIOR) CVP-FF Flat Roof Flushing CVP-FS CVP-FF CVP-RF12 CVP-VC Vertical Termination  Figure 17.3 CVP Pipe Components Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...
  • Page 59: Contact Information

    5890485, 5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729, 8147240 or other U.S. and foreign patents pending. 2000-945B Printed in U.S.A. - Copyright 2014 Heat & Glo • HE36CLX-S • 2183-900 Rev. H • 1/14...

This manual is also suitable for:

He36clxlp-s

Table of Contents