Table of Contents

Advertisement

Quick Links

Model:
FB-ZC
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a re
or explosion may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other am-
mable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas
- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the re department.
• Installation and service must be performed
by a quali ed installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer's instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
CAUTION
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07
Owner's Manual
Installation and Operation
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Glass and other surfaces are hot during
operation and cool down.
• Keep children away.
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high temperatures.
• Do NOT operate with protective barriers open or
removed.
• Keep clothing, furniture, draperies and other
combustibles away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the xed glass panel. Do
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber
or gas tter;
• a CO detector shall be installed in the room where the
appliance is installed.
Installation and service of this appliance should be
performed by quali ed personnel. Hearth & Home
Technologies suggests NFI certi ed or factory trained
professionals, or technicians supervised by an NFI
certi ed professional.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FB-ZC and is the answer not in the manual?

Questions and answers

Summary of Contents for Heat&Glo FB-ZC

  • Page 1 Technologies suggests NFI certi ed or factory trained professionals, or technicians supervised by an NFI This appliance is only for use with the type(s) of gas indicated certi ed professional. on the rating plate. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 2 BTUH: 00,000 00,000 00,000 00,000 MIN. MIN. INPUT INPUT BTUH: BTUH: 00,000 00,000 00,000 00,000 Serial Serial ORIFICE ORIFICE SIZE: SIZE: #XXXXX #XXXXX #XXXXX #XXXXX XXXXXXXX XXXXXXXX (Serie): (Serie): Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 3: Table Of Contents

    E. Contact Information ......38 = Contains updated information. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 4: Listing And Code Approvals

    Materials made of or surfaced with wood, compressed paper, plant bers, plastics, or other material that can ig- nite and burn, whether ame proofed or not, or whether plastered or unplastered shall be considered combustible materials. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 5: Getting Started

    Framing square Gloves Variable speed drill 1/4 Hex drive Safety glasses Manometer Phillips screwdriver Tape measure Non-corrosive leak check solution 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 6: Fireplace Size Requirements

    * NOTE: If exhaust collar on insert and replace damper do not line up, add 4 inches (102 mm) to minimum replace height for bends in vent pipe. Figure 3.1 Fireplace Opening Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 7: Clearances

    • Locate and install appliance to all clearance speci cations in manual. 12 in. MANTEL MAX. 12 in. MAX. TOP OF UNIT Figure 3.2 Clearances to Mantels or other Combustibles above Appliance Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 8: Termination Locations

    Over 16/12 to 18/12 ..........7.0 Over 18/12 to 20/12 ..........7.5 Over 20/12 to 21/12 ..........8.0 * 3 foot minimum in snow regions Figure 4.1 Minimum height from roof to lowest discharge opening Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 9: Vent Information And Diagrams

    BLOCK PIPE END WITH INSULATION OR ANY OTHER SEALING MATERIAL STAINLESS STEEL PIPE - 3 FT. MIN. REQUIRED (INCLUDED) SEAL DAMPER AREA INLET AIR VENT PIPE COLLAR ATTACHMENT BRACKET Figure 5.1 Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 10: Installation Preparation

    REFRACTORY • The solid fuel burning replace manufacturer’s REMOTE speci cation. RECEIVER UNIT • Local building codes required by authority having jurisdiction. • NFPA 211 EXISTING BOTTOM OF FIREPLACE Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 11: Installing Vent Pipe And Appliance

    • Flexible vent pipe for exhaust air (included with vent kit). purpose. • One pipe-to-cap adaptor (included with vent kit). • One vertical termination cap (included with vent kit). Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 12 OPTIONAL LINK-ZC-ADPB (For Flashing Class-A Pipe) SLIDING PLATE CLASS A WOOD PIPE INLET AIR VENT PIPE STAINLESS STEEL 3 INCH ADAPTER FOR EXHAUST COLLAR (MUST BE INSTALLED) Figure 7.1 Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 13: Placing, Securing And Leveling The Appliance

    • Install fiberglass insulation pieces to back face of surround. • Attach surround. Follow instructions accompanying surround. • Push insert so that surround becomes tight against face of replace. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 14: Installing Adaptor And Termination Cap

    3 screws. Connect both the LINK-ZC-ADPB to Class VENT PIPE achieve full 30’ A Pipe and the termination cap to the LINK-ZC-ADPB length. with the self tapping screws provided. Figure 7.4 Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 15: Gas Information

    5.0 inches 11.0 inches Minimum inlet pressure w.c. w.c. 14.0 inches 14.0 inches Maximum inlet gas pressure w.c. w.c. 3.5 inches 10.0 inches Manifold pressure w.c. w.c. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 16 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory. • Changing valve settings may result in re hazard or bodily injury. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 17: Electrical Information

    Figure 9.1). STANDING PILOT REMOTE SWITCH PIGTAIL ON/OFF VALVE SWITCH OPTIONAL WALL SWITCH, THERMOSTAT OR REMOTE Figure 9.1 Standing Pilot Ignition Wiring Diagram Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 18: Junction Box Installation

    Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. WARNING Shock hazard. • Replace damaged wire with type 105º C rated wire. • Wire must have high temperature insulation. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 19 105 º crated wire. NOTE: Do NOT install blower if using operable glass doors. Figure 9.4 Fan Wiring Diagram Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 20: Finishing

    12 in. MANTEL MAX. 12 in. MAX. TOP OF UNIT Figure 10.1 Clearances to Mantels or other Combustibles above Appliance Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 21: Appliance Setup

    • Follow ember placement instructions in manual. • Do NOT place embers directly over burner ports. • Replace ember material annually. Improperly placed embers interferes with proper burner operation. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 22: Positioning The Logs

    Place log #1 on the rebox ledge as shown. The front portion of the log should hang over the ledge as shown. The log should be placed all the way back and in the center of the ledge. 2019-700C 12/03 Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 23 #3 should be ush against the right grate tine. LOG #4 (SRV327-705): Place log #4 across log #1 and log #2 in the grooved out areas as shown. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 24: Glass Assembly

    Adjustments should be made by a qualified released (see Figure 11.2). technician. Replacing Glass Assembly Replace the glass door on the appliance. Fasten the latches on the glass frame. Burner Full Open Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 25: Operating Instructions

    Immediately call a quali ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 26: Lighting Appliance

    OFF”. Do not force. For additional information on operating your Close control access panel. 464-903G Hearth & Home Technologies replace, please refer to www. replaces.com. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 27: Check Pilot Flame Appearance

    • Replace cap screw and seal to prevent gas leaks. • Check for gas leaks after tightening. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 28: Frequently Asked Questions

    In an Intelli re ignition system it is normal to see the pilot ame, but it should turn off when continually? ON/OFF is turned off. In a standing pilot system the pilot will always stay on. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 29: Troubleshooting

    With the pilot in the ON position, disconnect the thermopile leads from the valve. Take a reading at the thermopile leads. The read- ing should be 325 millivolts minimum. Replace the thermopile if the reading is below the minimum. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 30 Ensure that the glass is tightened properly on the unit, particularly on top corners. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 31: Maintaining And Servicing Appliance

    Clean: • Glass • Air passageways, grilles, control compartment • Burner, burner ports Risk of: • Fire • Delayed ignition or explosion • Exposure to combustion fumes • Odors Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 32 1. Verify operation of remote. 2. Replace batteries in remote transmitters and battery-powered receivers. 3. Verify batteries have been removed from battery back-up IPI systems to prevent premature battery failure or leaking. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 33: Reference Materials

    1-1/16 in. 27 mm 5-9/16 in. GAS INLET 141 mm FB ZC MODEL DIMENSIONS FB-IN Location Inches Millimeters 20-3/8 9-11/16 29-1/8 22-5/7 14-5/8 14-3/4 18-15/16 Figure 15.1 Appliance Dimensions Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 34: Vent Kits Components

    FLEX3-30/2: Two 3 inch exible liners expands to 30 feet FLEX3-CNCT each. FLEX-CNCT: Connector kit - 3 inch liner to 3 inch liner, Figure 15.3 Direct Vent Flex Liner Accessory Kits one connector per kit. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 35: Limited Lifetime Warranty

    3. HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, speci cations and prices of the Product. HEAT & GLO also reserves the right to discontinue styles and products. 060-981D 3/05 © 2005 Hearth & Home Technologies Inc. Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...
  • Page 36: Service Parts List

    6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending. Printed in U.S.A. - Copyright 2006 Heat & Glo • FB-ZC • 2019-900 Rev. F • 1/07...

Table of Contents