Havis DS-PAN-102 Installation Instructions

8 8 8 8 8 8 7 7 7 7 7 7
*IF USING A CF-30 COMPUTER
IN AN EXTREME RUGGED ENVIRONMENT
(OFF-ROAD/MILITARY), HAVIS
RECOMMENDS USING A CF-30 FRONT
HOOK AVAILABLE UPON REQUEST*
D D D D D D
C C C C C C
(3X) 1/4-20 X 5/8" BHCS
(120 10% IN-LBS)
*USE 3 SCREWS TO FASTEN
DOCK DOWN IF POSSIBLE*
B B B B B B
*RECOMMENDED HOLES
FOR MOUNTING WITH
2 SCREWS
*RECOMMENDED HOLES
FOR MOUNTING WITH
A A A A A A 3 SCREWS
DRAWING NUMBER:
D3-0179-IS-B
(SHEET 1 OF 2)
8 8 8 8 8 8 7 7 7 7 7 7
6 6 6 6 6 6
PLUG INTO "DC INPUT" PORT
OF DOCKING STATION
*POWER CORD*
(NOT INCLUDED WITH DS-PAN-103)
CONNECT TO 12 VDC POWER SOURCE
RED (+), BLACK (-)
WARNING: ALL HAVIS INC. PRODUCTS ARE DESIGNED WITH SAFETY OF USE AND INSTALLATION IN MIND. HOWEVER,
IT IS THE SOLE RESPONSIBILITY OF THE OWNER/OPERATOR OF A VEHICLE USING HAVIS INC. MOUNTING AND
DOCKING EQUIPMENT, TO INSURE THAT THE EQUIPMENT IS INSTALLED SO THAT IT WILL NOT INTERFERE WITH VEHICLE
OPERATION, INTERFERE WITH SAFETY DEVICES, OBSTRUCT VIEW OF DRIVING CONDITIONS, OR IN ANY WAY
DEGRADE OCCUPANT SAFETY. IMPROPER INSTALLATION CAN CAUSE SERIOUS INJURY IN THE EVENT OF AN
ACCIDENT. INSTALLATION SHOULD ONLY BE PERFORMED BY QUALIFIED PROFESSIONALS. COMPUTERS AND
MOTION DEVICES MUST BE MOVED TO AND STOWED/SECURED IN THEIR SAFE DRIVING POSITIONS BEFORE
OPERATING VEHICLE.
6 6 6 6 6 6
5 5 5 5 5 5
4 4 4 4 4 4
(4X) 1/4-20 X 5/8" BHCS
(120 10% IN-LBS)
(MOUNTING BRACKET OF
DOCKING STATION)
HARDWARE KIT CONTENTS:
PRODUCT DESCRIPTION
THIS PRODUCT IS USED WITH THE PANASONIC
CF-28/29/30 TOUGHBOOK COMPUTERS (USED WITH KEY
#25425).
(THE FEATURES OF THIS PRODUCT MAY BE LIMITED
DEPENDING UPON THE MODEL OF COMPUTER USED.)
4 4 4 4 4 4
5 5 5 5 5 5
2 2 2 2 2 2
3 3 3 3 3 3

INSTALLATION INSTRUCTIONS:

1. REMOVE THE 1/4-20 X 5/8" BHCS HOLDING THE MOUNTING
BRACKET TO THE REST OF THE DOCKING STATION (THE SCREWS
IN THE PLASTIC SIDE-MEMBERS ON EACH SIDE OF THE DOCK).
PULL MOUNTING BRACKET OFF OF DOCKING STATION.
2. SET MOUNTING BRACKET ON TOP OF DESIRED SURFACE SO
THAT 3 OF THE HOLES ON THE MOUNTING BRACKET LINE UP WITH
3 TAPPED HOLES OF THE MOTION ACCESSORY. (IF 3 HOLES ARE
NOT AVAILABLE THEN USE 2.) SEE *RECOMMENDED HOLES* OF
THE MOUNTING BRACKET.
3. FASTEN THE MOUNTING BRACKET TO THE MOTION ACCESSORY
USING (3X) 1/4-20 X 5/8" BHCS (OR 2 DEPENDING ON AVAILABILITY).
4. PLACE DOCKING STATION OVER TOP OF MOUNTING BRACKET
SO THAT THE 2 THREADED HOLES IN EACH FLANGE OF THE
MOUNTING BRACKET LINE UP WITH THE 2 HOLES IN EACH PLASTIC
SIDE-MEMBER.
5. FASTEN THE DOCKING STATION BACK TO THE MOUNTING
BRACKET USING (4X) 1/4-20 X 5/8" BHCS.
6. TIGHTEN ALL FASTENERS TO THE INDICATED TORQUE
RECOMMENDATIONS.
7. TAKE END OF POWER CORD WITH 2 EXPOSED LEADS AND
ATTACH TO POWER SOURCE (RED TO "+" TERMINAL AND BLACK
TO "-" TERMINAL).
8. PLUG OTHER END OF POWER CORD INTO DC-INPUT PORT ON
DOCKING STATION (SEE SHEET 2). THE RED LED ON TOP OF DOCK
SHOULD LIGHT UP. IF NOT, CHECK POWER SOURCE AND CABLE
BEFORE CONTACTING HAVIS.
PRODUCT I.D. PRODUCT I.D. PRODUCT I.D. PRODUCT I.D. PRODUCT I.D. PRODUCT I.D.
DS-PAN-102
DS-PAN-103
PRODUCT NAME
3 3 3 3 3 3 2 2 2 2 2 2
1 1 1 1 1 1
D D D D D D
C C C C C C
B B B B B B
DATE DATE DATE DATE DATE DATE
05-18-09
DS-PAN-102/103 A A A A A A
DOCKING STATION
WEIGHT: (LBS) WEIGHT: (LBS) WEIGHT: (LBS) WEIGHT: (LBS) WEIGHT: (LBS)
4.4
REV. DATE REV. DATE
12-10-09
1-800-524-9900
WWW.HAVIS.COM
F-730-019 REV A
1 1 1 1 1 1