Download
Share
Print this page
Lincoln Electric IM10023 Operator's Manual
  1. Manuals
  2. Brands
  3. Lincoln Electric Manuals
  4. Controller
  5. IM10023
  6. Operator's manual
Lincoln Electric IM10023 Operator's Manual

Lincoln Electric IM10023 Operator's Manual

For use with machines having code numbers: 11590
Hide thumbs

Advertisement

Quick Links

Download this manual
RETURN TO MAIN MENU
M M A A X X s s a a 1 1 0 0 C C O O N N T T R R O O L L L L E E R R

Advertisement

loading
Need help?

Need help?

Do you have a question about the IM10023 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Lincoln Electric IM10023

Summary of Contents for Lincoln Electric IM10023

  • Page 1 RETURN TO MAIN MENU M M A A X X s s a a 1 1 0 0 C C O O N N T T R R O O L L L L E E R R...
  • Page 6 Thank You...
  • Page 10 STATUS LIGHT PENDANT CONNECTOR MAXsa™ 22 or 29 WIRE DRIVE CONNECTOR (14-PIN) POWER WAVE® AC/DC 1000 SD ARCLINK CONNECTOR FLUX HOPPER CONNECTOR ACCESS TC-3 TRAVEL CARRIAGE HOLES CONNECTOR...
  • Page 11 Front View Cover removed Pendant Cover Screws (4 places) Screws ( 2 Places) Access Hole Cover K1543-xx or K2683-xx Arclink Cable (Optional)
  • Page 12 INSERT WIRE HERE CAGE CLAMP VAC IN NEUTRAL (31) VAC IN LINE (32) INSERT SCREW DRIVER HERE REMOVE SCREW DRIVER FROM CAGE CLAMP HOLE.

  • Page 13: Wiring Diagram

    3-PIN FLUX 4-PIN TRAVEL RECEPTACLE RECEPTACLE CR1, CR2 CR3 Relays Numbers Refer to Relay Terminals TERMINAL STRIP Figure A.1 Wiring Diagram.
  • Page 14 Shorting Jumper Connect STOP Input Here...
  • Page 15 K2814-1 MAXsa™ 10 K1785-XX 14-Pin Cable K2370-2 MAXsa™ 22 K1811-XX Sense Lead Work Con gurations (Multi- Arc and Parelleled Power Sources) are in the Power Wave® AC/DC 1000SD Operators Manual K1543-XX or K2683-XX Arclink Cable 67 Lead Electrode K231-XX Weld Cable Contact Nozzle Connection Diagrams for Additional K2803-1...
  • Page 18 AMPS/WFS DISPLAY AMPS INDICATOR INDICATOR TRAVEL SWITCH (AUTO / OFF / MANUAL) FLUX FILL SWITCH WELD MODE SELECTOR WELD MODE INDICATOR FREQUENCY AND BALANCE INDICATOR MEMORY BUTTONS (8) MODE SELECT PANEL CONTROL MODE SELECT VOLTS PANEL (MSP) DISPLAY DISPLAY AMPS/WFS VOLTS CONTROL CONTROL...
  • Page 19 ---- ---- MAXsa Feed Cold Initializing. . . Feedhead 1 Setup Menu Feed FWD Hot! ELECTRODE HOT...
  • Page 20 Frequency Use Frequency to fine tune stability of imbalanced waveforms and multiple arc systems 1000 -500 Decrease Increase -1000 Balance Increased Balance 1000 More Penetration Nominal Balance Decreased Balance Less Deposition Less Penetration More Deposition -500 -1000 percent DC Offset Positive Offset More Penetration 1000...
  • Page 22 Arc Start Downslope Delay Start Upslope Weld Crater Burnback Strike Time Arc Delay Time Mode Select Panel Control Repeated pressing of the rc Start/End Options pushbutton will scroll through the parameters. Turning the Mode Select Panel Control, while on a parameter will change its value.
  • Page 23 Mode Select Panel Control Downslope Time Mode Select Panel Control...
  • Page 24 Mode Select Panel (MSP) Setup Menu Indicator User Prefs Exit Left Button Right Button Control Knob...
  • Page 30 ARC ESTABLISHED INDICATOR START BUTTON Steel 1/8” CC DC STOP BUTTON...
  • Page 32 DISPLAY Steel CC DC INDICATOR MEMORY BUTTON Hold for 2 Seconds to Save Press and Release to Recall 1/8” Memory 1 Saved...
  • Page 33 Set High Value Set Low Limit Low Limit Limit Hi=1050 Lo= 200 Weld Amps Parameter Name Memory 1 Set Limits Save Limits...
  • Page 36 Step 3. RECOMMENDED COURSE OF ACTION Step 1. LOCATE PROBLEM (SYMPTOM). Step 2. POSSIBLE CAUSE.
  • Page 44 Enhanced Diagram...

This manual is also suitable for:

Maxsa 10