Selecting Inputs And Outputs For Dante; Axp 50 C At Inputs And Outputs - Extron electronics AXP 50 C AT User Manual

Selecting Inputs and Outputs for Dante

Dante Controller is used for all network level signal routing of AT bus inputs and outputs.
The digital input and output channels of the AXP 50 C AT are shown in Dante Controller
as transmitters and receivers. The digital inputs, pre-processing, and line outputs are all
available in Dante Controller for routing to other Dante devices.
AXP 50 C AT Inputs and Outputs
Two sections provide output signals on the AT bus as Dante transmitter channels (see
figure 32,
Audio from these outputs is always available to Dante compatible devices on the same
network.
Two sections receive input signals from Dante network transmitters: the digital inputs and
the AEC reference inputs (see figure 32,
Figure 32.
The AXP 50 C AT inputs (
input mode, the analog signals on the rear panel inputs are converted to digital before the
gain stage. In digital mode (see
channels on the Dante network. The inputs are always available to Dante compatible
devices on the same network. Unless renamed, the five digital inputs are in the Dante
receiver list as
In addition, an AEC reference can be selected from any Dante device transmitter (outputs).
If they have not been renamed, the five AEC reference inputs are listed as Dante receivers
REFERENCE‑01
All AXP 50 C AT outputs (
from these outputs is always available to Dante compatible devices on the same network.
Unless renamed, the five pre-processor outputs (
as
controller as transmitters (
Both pre-processor and line outputs (Dante transmitters) can be connected to any Dante
device receiver.
, and ). All AXP 50 C AT outputs appear to Dante Controller as transmitters.
G H
DSP Con gurator - DSPcon g1 AXP 50 C AT
Inputs
ANG
Mic/Line In#1 ANG ANG
FILT FILT FILT
GAIN GAIN GAIN N
ANG
ANG ANG
Mic/Line In#2
FILT
FILT FILT
GAIN GAIN GAIN N
ANG
Mic/Line In#3 ANG ANG
FILT
FILT FILT
GAIN
GAIN GAIN N
ANG ANG ANG
Mic/Line In#4
FILT
FILT FILT
GAIN
GAIN GAIN N
ANG
ANG ANG
Mic/Line In#5
FILT
FILT FILT
GAIN
GAIN GAIN N
DSP Configurator Outputs (Dante Transmitter Channels)
) can be switched from digital to analog input mode. In analog
A
DIGITAL_IN‑01
to
REFERENCE‑05
and
G
to
PRE‑OUT‑01 PRE‑OUT‑05
OUTPUT‑01
, and -AEC).
A E
Current Emulation
AEC AEC AEC DYN DYN DYN DYN DYN DYN GAIN
AEC DYN DYN GAIN
AEC AEC DYN DYN DYN DYN GAIN GAIN
AEC DYN DYN GAIN
AEC AEC DYN DYN DYN DYN GAIN GAIN
AEC DYN DYN GAIN
AEC AEC DYN DYN DYN DYN GAIN GAIN
AEC DYN DYN GAIN
AEC AEC DYN DYN DYN DYN GAIN GAIN
Input Channels on page 31) the inputs are receiver
to .
DIGITAL_IN‑05
corresponding to the five input channels.
) are listed as transmitters in Dante Controller. Audio
H
) are in the Dante transmitter list
G
). The AXP 50 C AT output lines (
through ).
OUTPUT‑05
AXP 50 C AT • Dante Configuration and Operation
Pre-Processing AT Outputs
PreProcOut#1
PreProcOut#2
PreProcOut#3
PreProcOut#4
PreProcOut#5
AT Outputs
ATOut#1
ATOut#2
ATOut#3
ATOut#4
ATOut#5
) are listed in Dante
H
63