Recording System Check; Preparation For Recording; Ic1501(Vfd) Bist (Rec) Check; Ic1600(Sfd) Bist (Rec) Check - Sony Handycam DCR-PC1 Service Manual

• ENC Ya BIST Check
29) Select page: 3, address: 10, set data: 8C, and press the PAUSE
button of the adjustment remote commander.
30) Select page: 3, address: 12, set data: 10, and press the PAUSE
button of the adjustment remote commander.
31) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
32) Select page: 3, address: 13, set data: 04, and press the PAUSE
button of the adjustment remote commander.
33) When the playback system from IC1501 (VFD) to IC1402
(AOI) is normal, the display data (combination data) of page:
3, addresses: 16 and 17 agrees with any combination as shown
below.
NTSC model PAL model
Address Data Address
16 83
17 9E
• ENC Ca BIST Check
34) Select page: 3, address: 10, set data: 8D, and press the PAUSE
button of the adjustment remote commander.
35) Select page: 3, address: 12, set data: 10, and press the PAUSE
button of the adjustment remote commander.
36) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
37) Select page: 3, address: 13, set data: 04, and press the PAUSE
button of the adjustment remote commander.
38) When the playback system from IC1501 (VFD) to IC1402
(AOI) is normal, the display data (combination data) of page:
3, addresses: 16 and 17 agrees with any combination as shown
below.
NTSC model
Address Data
16 FE 22
17 68 CA
• ENC Cb BIST Check
39) Select page: 3, address: 10, set data: 8E, and press the PAUSE
button of the adjustment remote commander.
40) Select page: 3, address: 12, set data: 10, and press the PAUSE
button of the adjustment remote commander.
41) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
42) Select page: 3, address: 13, set data: 04, and press the PAUSE
button of the adjustment remote commander.
43) When the playback system from IC1501 (VFD) to IC1402
(AOI) is normal, the display data (combination data) of page:
3, addresses: 16 and 17 agrees with any combination as shown
below.
NTSC model
Address Data
16 B2 DE
17 E7 EE
44) Select page: C, address: 51, set data: 03, and press the PAUSE
button of the adjustment remote commander.
45) Select page: 0, address: 01, and set data: 00.
Data
16 CC
17 ED
PAL model
Address Data
16 70 43
17 D5 E4
PAL model
Address Data
16 ED 9A
17 CB 1E

2. Recording System Check

2-1. Preparation for Recording

1) Playback the BIST check tape (XH5-6 (NTSC), XH5-6P (PAL)).
2) Select page: 3, address: 10, set data: C0, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 3, address: 11, set data: 07, and press the PAUSE
button of the adjustment remote commander.
4) Enter the STOP mode.
5) While keep the HOLD switch of the adjustment remote
commander at ON (SERVICE position), eject the BIST check
tape and insert a tape for recording in place of the tape.
6) Enter the camera recording mode.
Note: Perform all of the following checks in the camera record mode.

2-2. IC1501(VFD) BIST (REC) Check

1) Select page: 3, address: 12, set data: 10, and press the PAUSE
button of the adjustment remote commander.
2) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 3, address: 13, set data: 04, and press the PAUSE
button of the adjustment remote commander.
4) When the recording system from IC1501 (VFD) to IC1600
(SFD) is normal, the display data (combination data) of page:
3, addresses: 14 and 15 agrees with any combination as shown
below.
NTSC model
Address Data
14 D5
15 0B

2-3. IC1600(SFD) BIST (REC) Check

1) Select page: 0, address: 01, and set data: 01.
2) Select page: C, address: AC, set data: 21, and press the PAUSE
button of the adjustment remote commander.
3) Select page: C, address: AD, set data: 03, and press the PAUSE
button of the adjustment remote commander.
4) Select page: 3, address: 11, set data: 04, and press the PAUSE
button of the adjustment remote commander.
5) Select page: 3, address: 12, set data: 08, and press the PAUSE
button of the adjustment remote commander.
6) Select page: 3, address: 12, set data: 00, and press the PAUSE
button of the adjustment remote commander.
7) Select page: 3, address: 13, set data: 03, and press the PAUSE
button of the adjustment remote commander.
8) When the recording system from IC1600 (SFD) to IC1602 (LIP)
is normal, the display data (combination data) of page: 3,
addresses: 16 and 17 agrees with any combination as shown
below.
NTSC model
Address Data
16 00 BC
17 15 CE
9) When the recording system from IC1600 (SFD) to IC1601
(TDF) is normal, the display data (combination data) of page:
3, addresses: 18 and 19 agrees with any combination as shown
below.
NTSC model
Address Data
18 F7 4F
19 F6 69
5-42
PAL model
Address Data
14 34
15 8A
PAL model
Address Data
16 2D
17 F5
PAL model
Address Data
18 6C
19 C7
A2
7B
23
76