dji Zenmuse H3-3D User Manual
  1. Manuals
  2. Brands
  3. dji Manuals
  4. Drones
  5. Zenmuse H3-3D
  6. User manual
dji Zenmuse H3-3D User Manual

dji Zenmuse H3-3D User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ZENMUSE H3-3D
User Manual
V1.04
2014.12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Zenmuse H3-3D and is the answer not in the manual?

Questions and answers

Related Manuals for dji Zenmuse H3-3D

Summary of Contents for dji Zenmuse H3-3D

  • Page 1 ZENMUSE H3-3D User Manual V1.04 2014.12...

  • Page 2: Warning & Disclaimer

    This product and manual are copyrighted by DJI with all rights reserved. No part of this product or manual shall be reproduced in any form without the prior written consent or authorization of DJI.

  • Page 3: Table Of Contents

    Video Connection Configuration Driver and PC Assistant Installation PC Assistant Interface Channel Setting Firmware & Software Upgrade Test Flight Pre-flight Checklist Gimbal Test Appendix Troubleshooting Settings When Using the A2 Flight Control System Specifications © 2014 DJI. All Rights Reserved.

  • Page 4: Profile

    Profile The Zenmuse H3-3D gimbal offers excellent stabilization features for aerial hobbyists and professional aerial photographers. Powered by a built-in IMU (Inertial Measurement Unit) and a special servo module, this gimbal is built to hold a GoPro camera and enables stable, quality aerial photography.
  • Page 5 ZENMUSE H3-3D User Manual Accessories Pack- Camera Securing Bracket × 1 Camera mounting bracket. Accessories Pack-Spare Screws × 1 M2.5x6.3: Used to mount your camera to the gimbal. M2.5x5: Used to secure the gimbal to the damping unit. M3x8, M3x6.5: Used to secure the gimbal to the aircraft.

  • Page 6: Installation

    1. Insert the securing pins into the holes on the upper plate of the damping unit as shown below. Then, attach the upper plate of damping unit to the Phantom 2 with four M3x5 screws. © 2014 DJI. All Rights Reserved.
  • Page 7 ZENMUSE H3-3D User Manual 2. Attach the bottom plate of the damping unit to the upper plate. To do this, insert the securing pins on the tip of the vibration absorbers into the mounting holes on the bottom plate. 3. Cover the securing pins with washers to lock the damping unit in place. Only push the washers past the first nut.

  • Page 8: Final Checks

    Camera Installation Follow the instructions below to mount your GoPro camera. Visit http://www.dji.com/product/zenmuse-h3-3d/video/ and watch the installation video tutorial before mounting your GoPro camera to the H3-3D gimbal. The gimbal cables are delicate items, handle with extreme care. Always check all connections before each flight and ensure they are secure.

  • Page 9: Gcu Connection

    Module and Flight Compass module to a Compass module to the module to the GPS port of Control System spare CAN-Bus port CAN 2 port on the A2. the PMU V2. Connection on the PMU. © 2014 DJI. All Rights Reserved.

  • Page 10: Gcu And Flight Control System Connection

    ZENMUSE H3-3D User Manual Refer to GCU and Flight Control System Connection for more information about the connection. For details on the flight control system connections, refer to the corresponding flight control system user manuals. 3. Connect the GCU to the flight control system. Then connect the 8-Pin cable of the gimbal to the G8 port on the GCU.

  • Page 11: Video Connection

    ZENMUSE H3-3D User Manual NAZA MUTI POTOR DIY power connector NAZA V-SEN 3V 5V EXP. NAZA-M V2 Connection Diagram Leave as-is DIY power NAZA V-SEN connector 3V 5V EXP. NAZA-M Connection Diagram The PMU and GCU can both connect to the same battery.
  • Page 12 ZENMUSE H3-3D User Manual 1. Solder the Video Signal/GND cables to your wireless video transmission module (air system). 2. Plug the gimbal video signal cable into the GCU video signal port. Ensure the wireless video transmission unit is connected to the GCU before powering on the aircraft.

  • Page 13: Configuration

    Phantom 2 PC Assistant information in your Phantom 2 User Manual instead. 1. Ensure the drivers for the flight control system are properly installed. 2. Download the PC Assistant from the official DJI website. 3. Launch the PC Assistant installer and follow each step to complete the installation.

  • Page 14: Firmware & Software Upgrade

    CAN-Bus cable between the GCU and main controller before you upgrade the firmware. Double check your set parameters once you have finished upgrading the firmware. Repeat the above steps if the DJI server is experiencing heavy traffic or the firmware upgrade fails.

  • Page 15: Test Flight

    Once such objects are no longer detected, the gimbal will resume normal operation. Use of a separate battery pack to test the gimbal is suggested before powering on the flight controller, gimbal, OSD, FPV gears, etc. © 2014 DJI. All Rights Reserved.

  • Page 16: Appendix

    Control System. Map the H3-3D to two channels on the transmitter as shown in the following diagram. DJI recommends the use of a knob switch or a stick with spring back function for tilt control, and a 2-position switch for MODE.

  • Page 17: Specifications

    42 mm ×32 mm ×9.3 mm Working Performance Angular Vibration Range Pitch/Roll:±0.02°, Yaw: ±0.03° Maximum Controlled Rotation Speed Tilt axis: ±130°/s Controlled Rotation Range Tilt axis control: -130 ~ +45° Regulatory Approvals FCC (USA) CE (EU) ROHS(EU) © 2014 DJI. All Rights Reserved.
  • Page 18 The content is subject to change. Download the latest version from http://www.dji.com/product/zenmuse-h3-3d/download © 2014 DJI. All Rights Reserved.

Table of Contents