Table of Contents
Advertisement
Inno Pocket Roll
Channel
Value
1
0 - 255
2
0 - 9
10 - 120
121 - 134
135 - 245
COUNTER CLOCKWISE SLOW - FAST
246 - 255
3
0 - 7
8 - 15
16 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
4
0 - 7
8 - 14
15 - 21
22 - 28
29 - 35
36 - 42
43 - 49
50 - 56
57 - 63
64 - 71
72 - 78
79 - 85
86 - 92
93 - 99
100 - 106
107 - 113
114 - 120
121 - 127
ADJ Products, LLC - www.adj.com - Inno Pocket Roll Instruction Manual Page 17
DMX Traits and Values
Function
PAN
TILT
STOP
CLOCKWISE ROLL SLOW - FAST
STOP
STOP
STROBE
BLACKOUT
OPEN
STROBING SLOW - FAST
OPEN
SLOW OPEN - FAST CLOSE
OPEN
FAST OPEN - SLOW CLOSE
REMOTE
INPUT
OPEN
SOUND
CONTROL
INPUT
RANDOM STROBE
OPEN
COLOR WHEEL
OPEN
GOBO 1 YELLOW
GOBO 2 RED
GOBO 3 GREEN
DMX512
GOBO 4 BLUE
DMX+,DMX-,COMMON
GOBO 5 RGB
GOBO 6 UV
GOBO 7 LIGHT BLUE
GOBO 8 UV & LIGHT BLUE
OPEN SHAKE
GOBO 1 YELLOW SHAKE
DMX512 OUT
3-PIN XLR
GOBO 2 RED SHAKE
GOBO 3 GREEN SHAKE
GOBO 4 BLUE SHAKE
GOBO 5 RGB SHAKE
GOBO 6 UV SHAKE
GOBO 7 LIGHT BLUE SHAKE
GOBO 8 UV & LIGHT BLUE SHAKE
SOUND
Inno Pocket Roll
daisy chained and cannot be split.
Notice:
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable's shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR's outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
1 Ground
OUTPUT
SOUND
Figure 3
Special Note: Line Termination.
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
COMMON
DMX +
1
1
DMX512 IN
3
3
3-PIN XLR
DMX -
2
2
CONTROL
INPUT
POWER
Be sure to follow figures two and three when making your own
DMX512
DMX+,DMX-,COMMON
COMMON
DMX +
1
DMX512 OUT
3
3-PIN XLR
DMX -
2
XLR Female Socket
XLR Male Socket
2 Cold
2 Cold
REMOTE
INPUT
OUTPUT
CONTROL
SOUND
INPUT
3 Hot
POWER
Termination reduces signal errors and
avoids signal transmission problems
1
and interference. It is always advisable
3
to connect a DMX terminal, (Resistance
2
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
ADJ Products, LLC - www.adj.com - Inno Pocket Roll Instruction Manual Page 6
SOUND
CONTROL
INPUT
Set Up
POWER
1
1
DMX512 IN
3
3
3-PIN XLR
2
2
Figure 2
XLR Pin Configuration
1 Ground
Pin 1 = Ground
REMOTE
INPUT
OUTPUT
CONTROL
Pin 2 = Data Compliment (negative)
INPUT
3 Hot
Pin 3 = Data True (positive)
When longer runs of cable are
POWER
Figure 4
SOUN
Termination
avoids sign
and interfere
to connect a
120 Ohm 1/4
and PIN 3 (
Advertisement
Table of Contents
