ADJ Inno Pocket Roll User Instructions page 6

Inno Pocket Roll
Power Supply:
The ADJ Inno Pocket Roll contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged into
a power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
DMX-512:
DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA "IN" and DATA "OUT" XLR terminals located on all DMX
fixtures (most controllers only have a DATA "OUT" terminal).
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Inno Pocket Roll can be controlled via DMX-512 pro-
tocol. The Inno Pocket Roll is a 6 channel DMX unit. The DMX address
is set electronically using the controls on the front panel of the unit. Your
unit and your DMX controller require a approved DMX-512 110 Ohm
Data cable for data input and data output (Figure
1). We recommend Accu-Cable DMX cables. If you
are making your own cables, be sure to use stan-
dard 110-120 Ohm shielded cable (This cable may
be purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end of
the cable. Also remember that DMX cable must be
ADJ Products, LLC - www.adj.com - Inno Pocket Roll Instruction Manual Page 5
Set Up Inno Pocket Roll
Channel
Inno Pocket Roll
The UC-IR infrared remote gives you control of various functions
(See below). To control the fixture you must aim the remote at the
front of the fixture and be no more then 30 feet away.
STAND BY - Pressing this button will blackout the fixture.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
FADE/GOBO - Press this button to enter Gobo mode. Use the 1-9
buttons to select your desired gobo. Adjust the output intensity using
the "DIMMER +" and "DIMMER -" buttons.
"DIMMER +" and "DIMMER -" - Use these buttons to adjust the out-
put intensity and to adjust the strobe speed.
STROBE - This button will activate the strobe effect. If you press and
hold this button the unit will begin to strobe.
COLOR - This button is invalid.
1-9 - When in either Gobo mode or Color mode, these buttons will
allow you to select either a gobo or color.
SOUND ON & OFF - These buttons activate and deactivate the
sound active mode.
SHOW - This activates the show mode. Use buttons 1-9 to select
your desired show.
Figure 1
Value
4 128 - 255 GOBO WHEEL ROTATION SLOW - FAST
5 0 - 255 MASTER DIMMER 0% - 100%
6
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101 - 255 DEFAULT DIMMER SETTING
ADJ Products, LLC - www.adj.com - Inno Pocket Roll Instruction Manual Page 18
DMX Traits and Values
Function
DIMMER MODE
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
UC IR Remote Control