Optical Multiplex Units; 1.Bru-H700.Hd.optical.multiplex.unit.for.use. With.the.brc-H700.And.brc-Z700 - Sony BRC-H700 Manual

5.2 Optical Multiplex Units

The.following.provides.information.on.the.location.and.function.of.BRU-H700.and.BRU-00/00P.parts..
With.these.optical.multiplex.units,.you.can.transmit.uncompressed.digital.data.including.video,.external.
sync,.and.camera.control.signals..
5.2.1 BRU-H700 HD Optical Multiplex
Unit for use with the BRC-H700
and BRC-Z700
Rear
CAMERA IN EXT SYNC OUT RGB/COMPONENT
Card slot
AUDIO OUT L/R jacks
Loop.through.output.of.the.audio.line.signal.
input.from.the.AUDIO.IN.jacks.on.the.BRBK-H700.
HD.Optical.Multiplex.Card.or.BRBK-MF1.HD.
Optical.Multiplex.Card.inserted.into.the.camera.
via.an.optical.fiber.cable.
~ AC IN connector
CAMERA connector
EXT SYNC IN connector
EXT SYNC OUT connector
RGB/COMPONENT connector
.
.Pin No. Signal Pin No.
. 1. Pr/R. 9.
. 2. Y/G. 10.
. 3. Pb/B. 11.
. 4. GND. 12.
. 5. GND. 13.
. 6. GND. 14.
. 7. GND. 15.
. 8. GND. .
VISCA RS-232C IN connector
Connect.to.the.RM-BR00.Remote.Control.Unit..
When.you.join.multiple.cameras,.connect.it.to.
the.VISCA.RS-C.OUT.connector.of.the.previ-
ous.camera.in.the.daisy.chain.
VISCA RS-232C OUT connector
When.you.join.multiple.cameras,.connect.it.to.
the.VISCA.RS-C.IN.connector.of.the.next.
camera.in.the.daisy.chain.
VISCA RS-422 connector
AUDIO OUT
L
R
FUNCTION ~
AC IN
1 6
VISCA RS-422
IN VISCA RS-232C OUT
Signal
NC
GND
GND
NC
HD-OUT
Tri-level.Sync/Bi-level.VD
NC
VISCA FUNCTION switches
Switch 1
(RS-232C/RS-422 selector)
Set.to.ON.for.RS-4,.or.OFF.for.RS-C.
Switch 2
(Communication baud rate selector)
Set.to.ON.for.8400.bps,.or.OFF.for.9600.bps.
Switches 3 to 5
(Camera address selectors)
Set.the.address.of.the.camera..Normally.set.to.
0..With.this.setting,.addresses.are.assigned.to.
the.cameras.automatically.in.the.connected.
order.by.pressing.the.POWER.button.while.
holding.down.the.RESET.button.on.the.
RM-BR00.Remote.Control.Unit..You.can.assign.
the.camera.address,.1.to.7,.manually.by.setting.
these.selectors.as.follows:
Camera
0 1 2
address
Switch 3 OFF ON OFF
Switch 4 OFF OFF ON
Switch 5 OFF OFF OFF OFF
Please.note.that.the.same.camera.address.
Note
cannot.be.assigned.to.two.or.more.different.
cameras.
Switch 6
(59.94i/50i signal format selector)
Set.to.ON.for.output.of.50i.signal.format,.or.OFF.
for.output.of.59.94i.signal.format.
Please.further.note.that.you.must.set.the.switches.
Note
before.you.turn.on.power.to.the.multiplex.unit.
3 4 5 6 7
ON OFF ON OFF ON
ON OFF OFF ON ON
ON ON ON ON
19
Location and Function of Parts