Important Safeguards - Cuisinart CMG-100C Instruction And Recipe Booklet

IMPORTANT
SAFEGUARDS
When using electrical appliances, basic
safety precautions should always be
followed including the following:
1. READ ALL INSTRUCTIONS.
2. To protect against risk of electrical
shock, do not put appliance in water
or other liquid.
3. Close supervision is necessary when
any appliance is used by or near
children. This appliance is not
recommended for use by children.
4. Unplug from outlet when not in use,
before putting on or taking off parts,
and before cleaning.
5. Avoid contacting moving parts.
6. Never put the unit near a hot burner,
in an oven, or in a dishwasher.
7. Do not operate the Cuisinart™ Meat
Grinder, or any other electrical
equipment, with a damaged cord or
plug or after the appliance
malfunctions, or is dropped or
damaged in any manner.
8. NEVER FEED FOOD BY HAND;
ALWAYS USE THE PUSHER. Keep
hands, hair, clothing and utensils
away from moving discs during
operation to reduce the risk of
personal injury and/or damage to the
Cuisinart™ Meat Grinder.
9. Do not use outdoors.
10. Warning- the cutting blade is sharp;
handle with care both when using
and when cleaning.
11. Do not let cord hang over edge of
table or counter, contact sharp
edges, or touch hot surfaces.
12. Do not pull on the power cord to
disconnect.
13. Never plug in the appliance where
water may flood the area.
14. Place the appliance on a firm and
stable surface.
2
15. NEVER PUT YOUR FINGERS NEAR
THE FOOD CHUTE WHILE GRINDER
IS IN OPERATION.
16. Ensure that the appliance is not
placed close to the edge of the table,
worktop, etc. where it can be pushed
off or fall.
17. The use of attachments not
recommended or sold by the
manufacturer may cause fire, electric
shock or injury.
18. Never use abrasive cleaning agents
or abrasive cloths when cleaning the
unit.
19. Do not use fingers to scrape food
away from Cutting Blade while
appliance is in operation. Cut type
injury may result.
20. Only use the unit when completely
assembled.
21. Do not leave the Cuisinart™ Meat
Grinder unattended while it is
running.
22. Before using for the first time,
remove all packaging and wash
parts.
23. This appliance has a polarized
plug (one blade is wider than the
other). To reduce the risk of
electric shock, this plug will fit in
a polarized outlet only one way. If
the plug does not fit the outlet
perfectly, reverse the plug. If it
should still not fit, contact a
qualified electrician. Do not
modify the plug in any way.
SAVE THESE
INSTRUCTIONS
FOR HOUSEHOLD
USE ONLY
PARTS
1. On/Off/Reverse Switch
2. Locking Knob
3. Motor Housing
4. Attachment Opening
5. Food Pusher
6. Die-Cast Hopper
7. Grinder/Feeder Head
8. Feed Screw
9. Cutting Blade
10. Cutting Plate (fine)
11. Cutting Plate (medium)
12. Cutting Plate (coarse)
13. Sausage Attachment (small)
14. Sausage Attachment (large)
15. Screwing Ring
ASSEMBLING
1. Make sure unit is unplugged while
assembling.
13
14
8
12
9
11
10
15
2. Place Grinder/Feeder Head tightly
into Attachment Opening. Holding
Head with one hand, place Locking
Knob into the hole on the side of the
Motor Housing and tighten knob by
turning clockwise.
3. Place Feed Screw into Grinder Tube,
long end spindle first; turn it slightly
until it is set into Motor Housing.
4. Position Cutting Blade onto Feed
Screw shaft with the blade facing out.
If it is not fitted properly, meat will not
be ground and the cutting plate may
be permanently damaged.
5. Position the desired Cutting Plate
onto the flat sides of the Cutting
Blade. Ensure that the notches of the
Cutting Plate fit into the slots of the
Grinder/Feeder Head.
6. Secure Screw Ring to the end of the
Grinder/Feeder Head by turning
clockwise.
7. Place Die-Cast Hopper on the
Grinder/Feeder Head.
5
6
4 2 1
7
3
3