Table of Contents
Advertisement
R20 assEmBlY STEP 2
SEAT HANDLEBARS
R20
BOLTS (D)
SPRING WASHERS (C)
MESH SEATBACK
INSIDE COVER
SEAT FRAME
OUTSIDE COVER
ARC WASHERS (F)
BOLTS (E)
SEAT RAIL
SCREWS (G)
HEART RATE WIRES
BOLTS (A)
SEAT RAIL
SPRING WASHERS (C)
SEAT RAIL
STOPPER
SEAT FRAME LOCK LEVER
BOLTS (A)
18
HARDwARE fOR STEP 2 :
SPRING
BOLT (D)
WASHER (C)
15 mm
15.4 mm
Qty: 4
Qty: 8
ARC
BOLT (A)
WASHER (F)
20 mm
18 mm
Qty: 6
Qty: 4
HEART RATE WIRES
a
open hardware for step 2.
B
mount the seat handlebars to the seat
frame with 4 bolts (d) and 4 spring
washers (c).
C
mount the seat bottom to the seat frame with
4 bolts (e) and 4 arc washers (f).
d
Place the inside cover over the mesh
seatback and mount the mesh seatback to
SEAT BOTTOM
the seat frame with 4 bolts (a) and 4 spring
washers (c).
attach the outside cover to the seat frame
E
and inside cover with 3 screws (g).
FIG. A
F
Push the seat frame lock lever forward and
side the seat frame onto the seat rail from the
rear of the bike.
g
Connect the heart rate wires in the seat
handlebars to the heart rate wires coming
up from the seat rail (fig.a).
H
attach the seat rail stopper (fig.a) to the
seat rail with 2 bolts (a).
R40 assEmBlY STEP 2
BOLTS (D)
BOLT (E)
SEAT RAIL
SPRING WASHERS (C)
35 mm
STOPPER
Qty: 4
Qty: 1
SEAT HANDLEBARS
SCREW (G)
20 mm
Qty: 3
MESH SEATBACK
BOLTS (G)
SEAT FRAME
BOLTS (G)
SEAT TILT ADJUSTMENT LEVER
PRE-INSTALLED SET SCREWS
HARDwARE fOR STEP 2 :
SPRING
BOLT (D)
WASHER (C)
20 mm
SEAT BOTTOM
15.4 mm
Qty: 6
Qty: 6
SEAT BOTTOM SUPPORT
SPRING
BOLT (G)
WASHER (F)
12 mm
12.2 mm
Qty: 6
Qty: 4
SPRING WASHERS (F)
a
open hardware for step 2.
B
Remove the pre-installed bolt from the front hole
BOLTS (E)
in the seat rail adjustment lever. Rotate the seat
lever into alignment on the bracket. Reinsert the pre-
installed bolt and tighten both bolts.
C
Connect the seat handlebar heart rate wires to
the seat frame heart rate wires. attach the seat
handlebars to the seat frame with 2 bolts (d) and
HANDLEBAR WIRES
2 spring washers (c) to the rear set of holes.
d
set the seat bottom support onto the main seat
frame so that the rear set of holes line up over the front
set of holes on the seat handlebar. secure in place
SEAT RAIL
ADJUSTMENT LEVER
with 4 bolts (e) and 4 spring washers (f).
E
attach the seat bottom cushion to the seat
PRE-INSTALLED BOLT
bottom support with 4 bolts (d) and 4 spring
washers (f).
BOLT (G)
slide the seat tilt adjustment lever in place over
F
the seat frame, making sure the handle of the seat
tilt adjustment lever is pointing up. Tighten the two
set screws in the seat tilt adjustment lever
bracket.
g
attach the mesh seatback to the seat frame using
6 bolts (g).
BOLT (E)
55 mm
R40
Qty: 4
19
Hide quick links:
Advertisement
Table of Contents
