Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Dahua IPC-HDW2200S
Summary of Contents for Dahua IPC-HDW2200S
- Page 1 HD IR Waterproof Network Dome Camera User’s Manual Version 3.5.1...
- Page 2 Welcome Thank you for purchasing our Network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
- Page 3 Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1.This series product supports PoE too. Please note: Do not connect these two power supplying sources to the device at the same time;...
- Page 4 Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.
-
Page 5: Table Of Contents
Table of Contents General Introduction ........................1 Overview ........................1 Features ......................... 1 Specifications ........................ 2 Factory Default Setup ....................3 Structure ............................8 Components ........................8 Framework and Dimension ..................8 Device Installation ........................10 Installation Steps ......................10 Restore Factory Default Setup Introduction ............ -
Page 6: General Introduction
1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 video compression technology, which maximally guarantees the video quality. -
Page 7: Specifications
1.3 Specifications Please refer to the following sheet for network camera performance specification. Model IPC-HDW2200S IPC-HDW3300S IPC-HDW3200S Parameter Main Processor TI Davinci high performance DSP Embedded LINUX System Support real-time network, local record, and remote operation at the Resources same time. -
Page 8: Factory Default Setup
396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The level has the highest sensitivity) Motion Detect Activation event: video storage, image snapshot, log, email function and etc. Record Priority Manual>External alarm >Video detect>Schedule Storage Support FTP storage. Management Wire Network 1-ch 10/100 M Ethernet , RJ45 port HTTP, TCP/IP, ARP, RTSP, RTP,UDP, RTCP, SMTP, FTP, DHCP,... - Page 9 Default Setup Setup Item IPC- IPC- IPC- HDW2200S HDW3300S HDW3200S Bit stream General type Encode mode H.264 Resolution 1080P(1920*1080) PAL: 25 Frame Rate(FPS) NTSC:30 Bit Rate Type Main Recommende Stream 3584-8192 Kb/S d Bit Bit Rate 8192 I Frame interval Watermark Enable Watermark...
- Page 10 Default Setup Setup Item IPC- IPC- IPC- HDW2200S HDW3300S HDW3200S Mode Static Device MAC address when it is shipped out of the Mac Address factory IP Version IPV4 IP Address 192.168.1.108 Subnet Mask 255.255.255.0 Default 192.168.1.1 Gateway Preferred 8.8.8.8 Alternate 8.8.8.8 Enable ARP/Ping set...
- Page 11 Default Setup Setup Item IPC- IPC- IPC- HDW2200S HDW3300S HDW3200S Disable Anonymity User Name anonymity Password **** Sender none Authenticatio n (Encryption mode) Title (Subject) IPC Message Attachment Mail Receiver 0 seconds Email Test Disable，interval=60 seconds UPnP Enable UPnP Disable SNMP Port Read public...
- Page 12 Default Setup Setup Item IPC- IPC- IPC- HDW2200S HDW3300S HDW3200S Masking Record Enable Channel Record Delay 10 seconds Send Email Disable Snapshot Disable Enable FTP Disable Server IP Port Username anonymity Password Remote path share Emergency Disable (Local) Pack Duration 8 minutes Pre-record 5 seconds...
-
Page 13: Structure
2 Structure 2.1 Components You can refer to the following figure for multiple-function combination cable information. See Figure Figure 2-1 Please refer to the following sheet for detailed information. Component Component Name Component 1 Device lens Component 2 Dome body Component 3 Dome enclosure Port... - Page 14 Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and Figure 2-3. Figure 2-2 Figure 2-3...
-
Page 15: Device Installation
3 Device Installation 3.1 Installation Steps Important Before the installation, please make sure the installation environments can at least support 3x weight of the camera. Please follow the steps listed below to install the device. Please refer to Figure 3-1 for reference. Step 1 Turn clockwise to remove the decoration ring from the snap joints. - Page 16 Figure 3-2 Note This series product supports two cable exits. One is from the bottom and the other is from the side. Please refer to the following figure for cable exit from the side information. Figure 3-3 Please earth the GND port of the device to enhance the device reliability. The GND port is near the cable exit port on the rear of the dome.
-
Page 17: Restore Factory Default Setup Introduction
Figure 3-4 3.2 Restore Factory Default Setup Introduction Important Please use RESET button when device is running. Step1 Please refer to step1 and step2 in chapter 3.1to loose the dome body. Push a little bit; you can take the dome body from the gland cover. Step2 Take the dome body out and then turn the top cover hard to remove. -
Page 18: Quick Configuration Tool
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 4-1. - Page 19 In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface. See Figure 4-3. In Figure 4-3, you can view device IP address, user name, password and port.
-
Page 20: Web Operation
5 Web Operation This series network camera product supports the Web access and management via PC. Web includes several modules: monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. ... - Page 21 Figure 5-2 If it is your first time to login in, system pops up warning information to ask you whether install control webrec.cab or not after you logged in for one minute. Please click OK button, system can automatically install the control. When system is upgrading, it can overwrite the previous Web too. If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the control download.
-
Page 22: Faq
6 FAQ I can not boot up Please click RESET button for at least five seconds to restore the device or factory default setup. operate properly. The water leakage The unauthorized front or rear cap remove many result in water occurred. -
Page 23: Appendix Toxic Or Hazardous Materials Or Elements
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component ○ ○ ○ ○ ○ ○ Device Case ○ ○ ○ ○ ○ ○...