Page 2
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without written permission of the EverFocus Electronics Corporation. Release Date: October, 2014 QuickTime is a registered trademark of the Apple Computer, Inc.
Safety Precautions Refer all work related to the installation of this product to qualified service personnel or system installers. Do not block the ventilation openings or slots on the cover. Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the power off immediately and contact qualified service personnel for service.
Page 4
Follow Instructions All operating and use instructions should be followed. Cleaning Unplug the unit from the outlet before cleaning. Do not use liquid cleaners, abrasive or aerosol cleaners. Use a damp cloth for cleaning Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards.
Page 5
This Product is RoHS compliant. Your EverFocus product is designed and manufactured with high quality materials and WEEE components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.
TABLE OF CONTENTS 1. Introduction ........................1 Features .......................... 3 Packing List ........................4 Optional Accessories ...................... 4 Front Panel ........................5 Rear Panel ........................6 2. Getting Started ....................... 7 Installation ........................7 2.1.1 Mounting ......................8 Hard Disk Installation ..................... 9 Vehicle Connection .......................
Page 7
4. OSD Root Menu ......................36 PTZ ..........................38 4.1.1 Express Control of PTZ ..................40 Layout Switching ......................41 Channel Switching ......................41 Display .......................... 42 Sequence ........................43 Monitor Switching ......................43 Zoom ..........................43 Archiving the Recordings or Log Data to the USB ............45 Logout ...........................
Page 8
Hard Disk ........................102 6.4.1 Disk ........................102 6.4.2 Lock/Format ..................... 103 Display Setting ......................104 6.5.1 Monitor OSD ....................104 6.5.2 M/T SEQ ......................105 Network Settings ......................106 6.6.1 LAN ........................106 6.6.2 Wireless ......................110 6.6.3 Mobile ......................112 6.6.4 Email ........................
Page 9
7.6.1.1 Manually Add an IP Camera from Remote Side ......... 153 7.6.1.2 Add an Configure an Analog Camera from Remote Side ....155 7.6.2 Auto Search ..................... 158 PTZ ..........................160 Remote Playback ......................162 8. Specifications ....................... 163 9. Troubleshooting ......................166 Appendix A: Network Overview ..................
The hybrid mobile DVR EMV401 / 801 / 1601 can support 4 / 8 / 16 channels in combination of analog and IP cameras, (EMV1601 supports maximum 8 channels of IP cameras). EMV401 / 801 / 1601 can deliver and record at real-time WD1 resolution of each analog camera and real-time 1080p resolution of each IP camera.
Main Monitor USB Storage Device (BNC) Panic *Audio Input Power Supply Button 3G USB Dongle Mouse * This diagram uses EMV1601 as an example. The EMV401 / EMV801 have 4 / 8 video inputs and 4 / 8 audio inputs respectively.
EMV401 / 801 / 1601 Hybrid Mobile DVR 1.2 Packing List • EMV401 / 801 / 1601 Hybrid Digital Video Recorder x 1 • HDD Tray (with 2 keys and 8 screws for 3.5” HDD, 6 screws for 2.5” HDD) x 1 •...
EMV401 / 801 / 1601 Hybrid Mobile DVR 1.4 Front Panel No. Name Description Two USB2.0 ports for connecting to the 3G USB dongle, USB USB2.0 Port storage device or mouse. RCA audio output for connecting to the speakers. The audio output Audio Out only works during playback.
EMV401 / 801 / 1601 Hybrid Mobile DVR 1.5 Rear Panel No. Name Description Antenna 1 (3G/4G) Connects to the 3G or 4G Receiver for using 3G / 4G LTE function. Power harness cable for connecting to 12 VDC ~ 24 VDC power DC Power Input source.
EMV401 / 801 / 1601 Hybrid Mobile DVR Chapter 2. Getting Started 2.1 Installation Before installation, choose a location in the vehicle where it can: • Provide convenient access for installing or removing the hard disk • Allow air to flow around the fan vents. Inadequate or improper air flow can impede proper...
EMV401 / 801 / 1601 Hybrid Mobile DVR 2.1.1 Mounting The EMV401 / 801 /1601 can be mounted horizontally. Two mounting types are available: Support-Mount and Suspend-Mount. Support-Mount Suspend-Mount To install the L-type brackets to the hybrid mobile DVR for mounting: Attach the supplied two L-Type Brackets to the Fixing Bracket on the hybrid mobile DVR.
EMV401 / 801 / 1601 Hybrid Mobile DVR 2.2 Hard Disk Installation The EMV401 / 801 / 1601 supply with a 3.5” HDD tray for inserting a Hard Disk for video recordings. Please follow the steps below to install the Hard Disk.
Page 19
EMV401 / 801 / 1601 Hybrid Mobile DVR 4. Push the Latch to fasten it to the HDD tray. 5. Lock the HDD tray using the supplied key. Locked Unlocked 6. To remove the HDD tray, slightly push the Lock Clip to loosen the Latch of the HDD tray.
EMV401 / 801 / 1601 Hybrid Mobile DVR 2.3 Vehicle Connection The EMV401 / 801 / 1601 supports input power voltage between 10 VDC ~ 32 VDC. You can install the hybrid mobile DVR in all kinds of vehicles support the above power voltage. The diagrams below are examples to illustrate the connection inside car / truck with 12 VDC / 24 VDC.
EMV401 / 801 / 1601 Hybrid Mobile DVR 2.3.2 Connecting to a Car with 12 VDC Glove box (inside or underneath) Trunk Passenger seat (underneath) Driver seat (between the seat and side panel) EMV1601 (Rear Panel) IGN (Yellow) Power Harness Cable...
EMV401 / 801 / 1601 Hybrid Mobile DVR 2.4 Basic Connection After installing the EMV401 / 801 / 1601 in the vehicle, you can start connecting the hybrid mobile DVR to the external devices. The instructions below describe the basic connection to the EMV401 / 801 / 1601.
EMV401 / 801 / 1601 Hybrid Mobile DVR 2.4.1 Power Harness Cable You can connect the mobile DVR to a power source between 10 VDC ~ 32 VDC. EMV1601 (Rear Panel) Power Input Power Harness Cable IGN (Yellow) DC Power In (Red)
2.4.2 Video Cable The EMV401 / 801 / 1601 have 1 / 2 / 4 Video In ports for connecting 4 / 8 / 16 analog cameras using the supplied Video Cables. The Video Cables are all labeled with VIN 1~ VIN 4, and you can connect any Video Cable to any of the Video In ports on the mobile DVR.
2.4.3 Audio Cable The EMV401 / 801 / 1601 have 1 / 2 / 4 Audio In ports for connecting 4 / 8 / 16 microphones using the supplied Audio Cables. The Audio Cables are all labeled with AIN 1~ AIN 4, and you can connect any Audio Cable to any of the Audio In ports on the mobile DVR.
EMV401 / 801 / 1601 Hybrid Mobile DVR 2.4.4 Alarm Cable You can connect the hybrid mobile DVR to 16 / 8 / 4 alarm inputs and 2 alarm outputs. EMV1601 (Rear Panel) Alarm Cable Alarm In / Out Alarm Output...
EMV401 / 801 / 1601 Hybrid Mobile DVR 2.4.5 RS-232 / RS485 Cable You can connect the I/O devices such as a CAN Bus / analog PTZ cameras using the RS-232 / RS- 485 Cable. EMV1601 (Rear Panel) Audio Input...
2.5 Monitor Connection The EMV401 / 801 / 1601 have 3 Main Monitor ports and 1 Call Monitor port. You can connect the monitors to the BNC, VGA or RCA Main Monitor and BNC Call Monitor ports of the hybrid mobile DVR.
Checking the Dynamic IP Address You can look up the IP address and access the Web interface of the hybrid mobile DVR using the IP Utility (IPU) program, which can be downloaded from EverFocus’ Website: http://www.everfocus.com/HQ/Support/DownloadCenter_p1.aspx. Please connect the hybrid mobile DVR in the same LAN of your computer.
Page 30
EMV401 / 801 / 1601 Hybrid Mobile DVR b. Type the Username and Password. Click the OK button, the status of the selected camera will display Login. Note: 1. The default user ID is admin and the default password is 11111111.
Page 31
4. When first connecting to the hybrid mobile DVR’s IP address, the following dialog will appear. Please check the box and click the Run button to run the EverFocus Viewer application. 5. You might be required to download ActiveX and JAVA software for viewing the camera feed.
EMV401 / 801 / 1601 Hybrid Mobile DVR 2.8 Connecting the Hybrid Mobile DVR to the Network There are three methods to connect the hybrid mobile DVR to the network: Router or LAN Connection, Direct High‐Speed Connection and One‐to‐One Connection. For more information of the network, please refer to Appendix A.
Page 33
Once you have a straight through cable plug one end into the LAN port on the back of the recorder and the other into the router. Log into the EverFocus hybrid mobile DVR menu and go to the Network Setting Menu. To let the router automatically assign an address: ...
Page 34
EMV401 / 801 / 1601 Hybrid Mobile DVR Take the values for Subnet Mask and Default Gateway and input them into the hybrid mobile DVR; these values should be exactly the same in both devices. However, you should change the last number of the IP address. For example, if the IP address of the computer is 192.168.2.101, the hybrid mobile DVR’s IP address...
the recorder and the other into the high speed modem. Log into the EverFocus hybrid mobile DVR menu and go to the Network Setting Menu. Input the Static IP address, the Subnet Mask, and the Gateway that you obtained from ...
hybrid mobile DVR and the other into the network card on the back of the computer. Log into the EverFocus hybrid mobile DVR menu and go to the Network Setting Menu. You must use the Static IP option for this type of connection.
Page 37
EMV401 / 801 / 1601 Hybrid Mobile DVR Go to Start. Double-click on Control Panel. Click Network and Sharing Center. Click Local Area Connection. ...
Page 38
EMV401 / 801 / 1601 Hybrid Mobile DVR Click Properties. Click on Internet Protocol Version 4 (TCP/IPv4) and then click Properties. ...
Page 39
EMV401 / 801 / 1601 Hybrid Mobile DVR Select Use the following IP address. Assign an IP address of 192.168.1.2, a Subnet Mask of 255.255.255.0, and a Default Gateway of 192.168.1.1 and then click OK. Restart both of the computer and the hybrid mobile DVR.
Chapter 3. General Operation There are two ways to control the OSD menu of the EMV401 / 801 / 1601: with a Mouse or the supplied handheld IR Remote Control. For details on the IR remote control, please refer to Appendix E, IR Remote Control.
EMV401 / 801 / 1601 Hybrid Mobile DVR 3.1.3 Field Input Options You may found the following fields in the Configuration menu. Follow the instructions below to configure the settings. Text Box: Click on the box and an on-screen keyboard will appear.
3.2.1 Login In order to access EMV401 / 801 / 1601, you may be prompted to log in for authority identification. To log in, follow the steps below: Right click on the screen to display the Root Menu. The following window appears.
1. If you forget your password, please email the Serial Number of the hybrid mobile DVR to techsupport@everfocus.com, and then EverFocus will send you a verification code. 2. Input this verification code in the Password field of the Login window within 24 hours, and check the Verification Mode box.
EMV401 / 801 / 1601 Hybrid Mobile DVR 3.2.4 Audio Selection In order to utilize the audio function, please follow the instructions below before switching on the audio function. Note: The Audio function is unavailable for Germany. 1. Connect the audio source and/or audio output amplifier to the hybrid mobile DVR.
EMV401 / 801 / 1601 Hybrid Mobile DVR Chapter 4. OSD Root Menu Name Description Click to display the Playback Bar for viewing the recording videos. For Playback details, please refer to 5. Search and Playback. Click to display the PTZ Control Panel for controlling the connected PTZ cameras.
Page 46
EMV401 / 801 / 1601 Hybrid Mobile DVR Click to display the Channel Changing Bar as show below. To switch the selected camera to a specific channel, please refer to 4.3 Channel Switching. Change Channel Click to display system information icons or status icons on the live Display view screen.
EMV401 / 801 / 1601 Hybrid Mobile DVR 4.1 PTZ You can use the PTZ Control Panel to control the connected PTZ cameras. To bring up the PTZ control panel, on the OSD Root Menu, click the PTZ button The following actions can be performed using the PTZ Control Panel: 1.
Page 48
EMV401 / 801 / 1601 Hybrid Mobile DVR 9. To operate the Auto Pan function, click the Auto Pan button. 10. To operate the Pattern function, click the Pattern button. The Pattern is the “0” Tour in Everfocus and Pelco PTZ cameras.
EMV401 / 801 / 1601 Hybrid Mobile DVR 4.1.1 Express Control of PTZ If the PTZ Control Panel has first been opened and then hidden, the mouse can be used to control basic PTZ functions. Move your mouse cursor on the screen, the mouse cursor will turn into a control icon (direction, focus or zoom) in different areas of the screen.
EMV401 / 801 / 1601 Hybrid Mobile DVR 4.2 Layout Switching The hybrid mobile DVR have 7 screen division types available. The seven layouts are shown as below: To change layout, follow the steps below: 1. Right-click to bring up the OSD Root Menu.
EMV401 / 801 / 1601 Hybrid Mobile DVR 4.4 Display You can display system and camera status on the live view screen. Follow the steps below: 1. Click the Display button on the OSD Root Menu or press the Display button on the front panel to display the system and camera status.
EMV401 / 801 / 1601 Hybrid Mobile DVR 4.5 Sequence The sequence function is used to display each channel in sequence mode. To enable this function: Click the Sequence button to enter the sequential switching mode. The hybrid mobile DVR will display one channel at a time in full screen.
Page 53
EMV401 / 801 / 1601 Hybrid Mobile DVR To enter the Zoom mode: Select a camera and then click the Zoom button on the OSD Root Menu to zoom in the camera view to 2X. The ZOOM 2X stamp will be displayed on the top screen.
EMV401 / 801 / 1601 Hybrid Mobile DVR 4.8 Archiving the Recordings or Log Data to the USB You can archive the recordings or log data (event and motion) to the USB storage device. On the OSD Root Menu, click the Copy icon , the following menu appears.
Page 55
EMV401 / 801 / 1601 Hybrid Mobile DVR EFPlayer: Unzip the EFPlayer file and double-click to open it as below. The EFPlayer can only display up to 16 channels at one time. No. Name Function Description Shows the recording information of the device, including...
Page 56
EMV401 / 801 / 1601 Hybrid Mobile DVR : Click to fast reverse / fast forward. Playback Controls : Click to reverse play /play. : Click to pause play backing. Click to take a snapshot of the channels displayed on the UI.
EMV401 / 801 / 1601 Hybrid Mobile DVR 4.9 Logout You can log out the hybrid mobile DVR by clicking the Logout icon on the OSD Root Menu to bring up the Logout Confirmation window as Figure 4-9. Press “Yes” when you are ready to logout of the system.
EMV401 / 801 / 1601 Hybrid Mobile DVR 4.9.1 Temporarily Logout You can temporarily log out the hybrid mobile DVR by clicking the Logout icon on the OSD Root Menu. This function is designed for use in conjunction with the Covert Camera function, but it only supports analog camera streams only.
Page 59
EMV401 / 801 / 1601 Hybrid Mobile DVR 2. Check the Covert box. 3. Click the Logout icon on the OSD Root Menu, the Logout menu appears. 4. Click the Yes button and the selected camera streams will be hidden on the Live View / Sequence Mode.
EMV401 / 801 / 1601 Hybrid Mobile DVR Chapter 5. Search and Playback You can use the Quick Playback function to play back the recordings start from the pre-configured time or use the Search functions to search for the desired recordings for playing back.
EMV401 / 801 / 1601 Hybrid Mobile DVR 5.2 Playback Bar The playback bar is the fastest way to show video from the exact time which users want to see. The playback bar allows users to see both a timeline and the current playback indicator. Users can then click the timeline to move the indicator to the desired position.
Page 62
EMV401 / 801 / 1601 Hybrid Mobile DVR No. Name Description Click to play the recorded data forward. Click this button again to Play/Pause Pause the playback. Click the Stop button to stop all playback actions and exit the playback area.
EMV401 / 801 / 1601 Hybrid Mobile DVR 5.3 Searching the Recordings for Playing Back You can search the recordings for playing back by using the Search menu. On the left side of the Search menu, select Time Search, Event Search or Snapshot Search to enter to the setup menu.
EMV401 / 801 / 1601 Hybrid Mobile DVR 5.3.2 Event Search Start Date / End Date: Click to bring up the on-screen keyboard to select the start / end date. Start Time / End Time: Click to bring up the on-screen clock to select the start / end time.
EMV401 / 801 / 1601 Hybrid Mobile DVR 5.3.3 Snapshot Search You can display video frames in snapshot and resume a video from where the snapshot has been set up. Search Date: Click to bring up the on-screen keyboard to select the date.
Page 66
EMV401 / 801 / 1601 Hybrid Mobile DVR To resume the video: 1. Click the Search button, the search results are displayed in 16 screen division. In this picture, you can see the time layouts on the upper-left corner of each snapshot, which are set up with 5-minute interval.
Chapter 6. Configuration The EMV401/801/1601 can be configured through a series of menus on screen by using a Mouse or the supplied IR Remote Control. The following operations are examples of using a Mouse. This chapter describes the functions and options of the Configuration Setting in the on-screen display (OSD) menus.
Page 68
EMV401 / 801 / 1601 Hybrid Mobile DVR List of Configuration Options: Please find the topic of interest by referring to the section prefixed to each option. 6.1.1 Camera Status 6.1.2 Auto Search 6.1.3 PTZ 6.1 Camera 6.1.4 Tracking 6.1.5 Pattern Tour 6.1.6 Adjust...
Page 69
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.8.5 I/O Control 6.8.6 EKB200 Setting 6.8.7 Miscellaneous 6.10.1 System 6.10 System Information 6.10.2 Log...
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.1 Camera You can add IP cameras automatically by search or manually in these settings, and you can configure the settings for each analog and IP cameras. You can also set up the PTZ, Tracking, Pattern and Tour functions only for IP PTZ cameras.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.1.1.1 Manually Add an IP Camera: On the channel which you want to add an IP camera, click to select IP from the Type option, and click the Add button. (For EMV1601, you can only add up to 8 IP cameras).
Page 72
EMV401 / 801 / 1601 Hybrid Mobile DVR 3. Click Auto Detection to auto detect the Protocol, Brand and Model of the camera. Then, there will be a message popping up to remind you to check the settings in step 2, if they are correct, just click Yes to continue.
Page 73
EMV401 / 801 / 1601 Hybrid Mobile DVR 5. You can just click Save to add this camera, or you can also configure the detailed settings before saving. 【 Main / Sub Stream Parameter 】 You can separately configure the settings for the Main / Sub Streams.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.1.1.2 Add and Configure the Analog Camera: On the channel which you want to connect and display an analog camera, click to select the Analog from the Type option. 2. Click Save to save the setting.
Page 75
EMV401 / 801 / 1601 Hybrid Mobile DVR Analog Camera Settings: Camera: Select a camera to be configured. Title: Click to bring up the on-screen keyboard for assigning a title for the selected camera. Each title supports up to 16 characters.
Page 76
EMV401 / 801 / 1601 Hybrid Mobile DVR Record Quality: Select a recording quality for the Main Stream and Sub Stream. The options include Low, Basic, Standard, High and Superior. The higher the quality, the more the HDD space is used.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.1.2 Auto Search This function allows you to automatically search and add the IP cameras connected in the same LAN network. Please see the steps below. 1. Before using the Auto Search function, you need to configure which channels you want to display IP camera live view from the Camera Status setting page, please refer to 6.1.1...
Page 78
EMV401 / 801 / 1601 Hybrid Mobile DVR 2. On the Auto Search page, click the Search button, and the IP cameras connected in the same network will show up in the Camera List. 3. To add cameras, there are two methods: A.
Page 79
EMV401 / 801 / 1601 Hybrid Mobile DVR B. You can also add the desired camera to channel one by one. a. Click on a desired camera, and then click Add to add that camera to the channel. b. Click on a desired channel, and click Add to add the camera to that channel.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.1.3 You can set up the Preset and Auto Pan settings in this page. 【 Camera 】 : Select a PTZ camera. 【 Speed 】 : Select a pan and tilt speed from the Speed drop-down list for the camera to move to the directions when you use the direction buttons during the configuration period 【...
Page 81
EMV401 / 801 / 1601 Hybrid Mobile DVR Preset: You can configure up to 192 preset positions in this field. To set up a Preset Positions: 1. Adjust the camera view to a desired position using the direction button. You can select the pan / tilt speed from the Speed drop-down list for controlling the direction buttons.
Page 82
EMV401 / 801 / 1601 Hybrid Mobile DVR Auto Pan: You can only configure one Auto Pan sequence. The configured Auto Pan (A to B Pan) sequence will always be numbered as “1”. The number “2” will always be an endless pan around the given (not preconfigured) X/Y tilt axis.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.1.4 Tracking To set up the Auto Tracking function: Auto Tracking Start Point: Check the box to enable a camera position to which the camera will return to after a tracking operation. Use the direction buttons to adjust the camera view to a desired position where you want to set up the position as the Auto Tracking Start Point.
Page 84
EMV401 / 801 / 1601 Hybrid Mobile DVR Note: Please note that if enabling the Pan/Tilt Limits function, the position of the Start Point should be within the range of the Pan/Tilt Limits, or there will be a pop-up message showing “Setting error: Start Point is not inside Pan/Tilt Limits”.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.1.5 Pattern Tour Pattern: You are given 90 seconds to move the camera (via the PTZ buttons) to different positions (and different zoom / focus / Iris positions). The camera then saves that sequence under the Pattern No.
Page 86
EMV401 / 801 / 1601 Hybrid Mobile DVR Tour: You can combine up to 16 preconfigured camera positions and patterns into one long sequence. Up to 16 Tour sequences can be set up. To set up a Pattern Sequence: 1. Select a number from the Tour No drop-down list.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.1.6 Adjust Setting You can adjust the detail camera settings in this page. Camera: Select a desired camera for adjusting the following settings. Device Title: Enter a camera title. Record Dual Stream: Select to enable or disable the dual streams recording function. (IP camera only) Record Mode: Select a recording mode from the drop-down list.
Page 88
EMV401 / 801 / 1601 Hybrid Mobile DVR Note: Whether the following functions marked with a “*” will be enabled or not depends on the connected IP camera. If the IP camera doesn’t have the any one of these functions, the function will not be enabled.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.2 Record & Playback 6.2.1 Alarm You can configure the basic recording settings on the hard disk. Record Overwrite: Check the box to overwrite the hard disk when it is full. Note that unless this box is checked, or the mobile DVR will stop recording when the hard disk is full.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.2.2 Playback You can set up the quick playback time on this page. For using this function, please refer to 5.1 Quick Playback. Quick Playback: Check the box to enable the Quick Playback function as described below.
Email operation requires valid email entered in the Email setup menu (see 6.6.4 Email). Network Alarm: Check the box to send out a network alarm to a client PC when an alarm event occurs. This feature works with EverFocus’ CMS software. You will need to configure...
Page 92
EMV401 / 801 / 1601 Hybrid Mobile DVR the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server). Auto Lock: Check the box and the events will be recorded in a write protected segment of the hard disk (will not be overwritten).
Network Alarm: Check the box to send out a network alarm to a client PC when video loss event occurs. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 94
EMV401 / 801 / 1601 Hybrid Mobile DVR Timeout: Select this option and then set up the Timeout Duration in the field below, the alarm output will last for the setup duration time (10 ~ 150 seconds). Permanent: Alarm will remain active until the user presses the “Enter” key on the IR Remote Control or resets the alarm remotely.
Network Alarm: Check the box to send out a network alarm to a client PC when motion occurs. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm...
Page 96
EMV401 / 801 / 1601 Hybrid Mobile DVR Auto Lock: Check the box and the events will be recorded in a write protected segment of the hard disk (will not be overwritten). The mobile DVR will lock a period of time when the alarm occurs.
Page 97
EMV401 / 801 / 1601 Hybrid Mobile DVR To Edit the Motion Grids: Note: The IP and analog camera motion setting methods are the same. Click the Edit Motion Grid button, the Motion Setting menu appears. Click on the image and the grid will be displayed.
Network Alarm: Check box to send out a network alarm to the client PC. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 99
EMV401 / 801 / 1601 Hybrid Mobile DVR Transparent: Alarm output remains active until event ends. Trans+Timeout: Alarm output continues until event ends, then continues for the set time duration. Timeout Duration: The amount of time the buzzer sounds when GPS event occurs.
Network Alarm: Check box to send out a network alarm to the client PC. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 101
EMV401 / 801 / 1601 Hybrid Mobile DVR Alarm Output: This will transmit a signal through the alarm output relay. It can be set to either “NONE” (not active), “1” (active) or “2” (active). Output Type: Output action when alarm is triggered.
Network Alarm: Check the box to send out a network alarm to a client PC when an alarm event occurs. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 103
Network Alarm: Check the box to send out a network alarm to a client PC. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 104
Network Alarm: Check the box to send out a network alarm to a client PC when HD fails. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 105
Network Alarm: Check the box to send out a network alarm to a client PC when HD is full. This feature works with EverFocus’ CMS software, including PowerCom and PowerVideo Plus. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 106
EMV401 / 801 / 1601 Hybrid Mobile DVR Permanent: Alarm will remain active until the user presses the “Enter” key on the IR Remote Control or resets the alarm remotely. Transparent: Alarm output remains as long as the alarm input is active.
Page 107
Network Alarm: Check the box to send out a network alarm to a client PC when HD is off. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 108
Network Alarm: Check the box to send out a network alarm to a client PC when power has been restored. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
Page 109
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.3.6.7 Network Loss Log: Check the box to record alarm events to log data. Buzzer: Check the box to enable buzzer when network is lost. Alarm Output: Select an alarm output number. When an alarm is triggered, the signal will be transmitted through the selected alarm output relay.
Page 110
Network Alarm: Check the box to send out a network alarm to a client PC when HD is off. This feature works with EverFocus’ CMS software. You will need to configure the Alarm Server for the mobile DVR to send network alarms to the client PC (see 6.6.7 Alarm Server).
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.4 Hard Disk The Disk menu is used to review the mobile DVR’s hard drive settings and status. No value in this menu can be configured by the operator. 6.4.1 Disk Record Time (Start): Shows the earliest recording time of the mobile DVR.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.4.2 Lock/Format You can control the percentage of the hard disk space reserved for Locked Event Recordings. You can also format the hard disk if necessary. Figure 6-25 Maximum Lock (%): Sets the maximum percentage of the hard disk space reserved for Locked Event Recordings.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.5 Display Setting You can configure the settings for displaying the camera / mobile DVR information on the live view image. You can also set up the sequencing order for the Main / Call monitor.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.5.2 M/T SEQ You can configure up to 20 steps of the sequencing order for the Main / Call monitor. The Sequence will repeat continuously from step 1 to step 20 until interrupted.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.6 Network Settings The mobile DVR allows you to use a Web browser to remotely view and manage the system. You can also receive live video streaming from the mobile DVR using your smartphone.
Page 116
EMV401 / 801 / 1601 Hybrid Mobile DVR Static IP: User can set a fixed IP for network connection. DHCP: DHCP server in LAN will automatically assign an IP configuration for the network connection. PPPoE: For direct connection to the DSL only. Verify with your ISP if they use PPPoE (The option is only for Lan2).
Page 117
EMV401 / 801 / 1601 Hybrid Mobile DVR Additional information: 1. Set up the mobile DVR Network Menu according to the instructions detailed in the Networking chapter of this mobile DVR’s manual. a. If using DHCP, all settings will be detected automatically. While DHCP is a useful tool...
Page 118
EMV401 / 801 / 1601 Hybrid Mobile DVR select functional ports and set up the port forwarding in your router. Other ports, such as 8080 and 8000 are sometimes blocked by ISPs as well. What port(s) should be used? There are 65,535 valid IP ports to choose from. These are broken down into three groups: •...
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.6.2 Wireless Wireless Mode: Two options are selectable: Static IP and DHCP. Static IP: User can set a fixed IP for network connection. DHCP: DHCP server in LAN will automatically assign an IP configuration for the network connection.
Page 120
EMV401 / 801 / 1601 Hybrid Mobile DVR DNS Server 2: This field shows the secondary DNS server for your network. Network Mode: Select a wireless networking standard. SSID: Enter the name (SSID) of the wireless network. Shared Key: Enter the password of the wireless network.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.6.3 Mobile After connecting the 3G USB dongle or connect the 3G Receiver to Antenna 1 port of the mobile DVR, you have to set up the mobile settings for the mobile DVR to connect to the wireless network.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.6.4 Email You can configure the Email settings for mobile DVR to send Email alert when an event occurs. SMTP Server: Assign the SMTP (e-mail) server’s name. Note that for more reliable email service, use the server’s IP address.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.6.5 DDNS DDNS (Dynamic Domain Name System) is a service used to map a domain name to the dynamic IP address of a network device. You can set up the DDNS service for remote access to the mobile DVR.
Page 124
~ ! @ # $ % ^ & * ( ) + < > " ; : . , Note: 1. It is not necessary to append the HTTP port number to the DDNS name. The EverFocus DDNS server not only keeps track of your mobile DVR’s IP address, but also keeps track of the ports.
Page 125
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.6.5.2 www.dyndns.org DDNS Service: Select www.dyndns.org from the drop-down list. Host name: Host name created through the dyndns account. User name: User name of the dyndns account. Password: Password of the dyndns account.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.6.6 Set up the FTP server settings to enable the FTP function. The function is for users to upload the alarm / motion recordings or snapshots from sub stream to the FTP server. You can choose to upload either the recordings or snapshots, please see 6.2.1 Alarm and 6.3.3 Motion.
6.6.7 Alarm Server You can send out the alarm notifications to EverFocus’s CMS software. Please also consult the CMS’s user manual for network alarm settings. Server IP1~3: IP address of client PC. The network alarm can be transmitted to up to 3 addresses.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.6.8 Network Testing The Ping utility is useful in diagnosing connectivity problems by obtaining responses from nodes progressively farther along the network. DNS functionality can also be confirmed by entering a valid DNS name instead of an IP address.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.7 Schedule Setting You can set up the recording schedule with the desired time, event types or FPS. 6.7.1 Express Setup You can set up a weekly recording schedule for the mobile DVR to automatically record videos.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.7.2 Holidays In addition to set up a weekly recording schedule, you can also set up a holiday recording schedule to automatically record videos on a specific day of the year. Date Type: Select Holiday or Others if you have configured the settings in 6.8.1 Express Setup.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.7.3 Schedule You can set up the camera recording mode by time of day on specific days of the week and/or holidays and other days. Please note that after the configuration, you have to check the Schedule Record box in the Record setting page to enable the schedule recording mode.
Page 132
EMV401 / 801 / 1601 Hybrid Mobile DVR Schedule setting using Mouse Select a camera first and click on desired start time block (no number on it) on a time bar. At this time, the selected time block will be highlighted in yellow frame and the entire time bar will be highlighted by red frame.
Page 133
(NTSC – 25 PAL) per individual camera (real time recording). The PARAGON960 x4 can record 480 fps (NTSC) / 400 fps (PAL) at WD1. Since EverFocus mobile DVRs have the capability to change the FPS rate in response to events, it may be advisable to reserve some recording capacity for event response.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.8 System Setting You can configure the general settings for the mobile DVR in this menu. 6.8.1 Date / Time You can set up the date and time for the mobile DVR.
Page 135
EMV401 / 801 / 1601 Hybrid Mobile DVR Time Zone: Select a time zone for the mobile DVR to adjust to when updating from the time server. NTP: Select Disable / Enable for NTP time synchronization. NTP Server: Displays the time server address that the mobile DVR uses for time synchronization.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.8.2 Daylight Saving You can configure the settings for mobile DVR to automatically adjust to daylight saving time. Note: If this page is grayed out, it means that you have enabled the Auto daylight saving function, please refer to 6.8.1 Date/Time.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.8.3 User Group This setting page is used for configuring the privilege of the three access levels: Administrator, Manager and Operator. Check the boxes under an access level to enable the privileges of that access level.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.8.4 User Management You can create multiple user accounts (max: 20 user accounts) with different privileges. The mobile DVR has default user accounts which you can choose to copy, edit, add or delete, and the default password is 11111111.
Page 139
EMV401 / 801 / 1601 Hybrid Mobile DVR Previous: Click to return to the previous page. Next: Click to enter the next page. Apply: Click to apply all the settings. You can further configure each user account and its settings individually, see the steps below: 1.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.8.5 I/O Control The I/O Control setup menu is used to define the settings for controlling the mobile DVR through RS-485 / RS-232 communication protocol and for mobile DVR to control the connected PTZ cameras.
Page 142
RS-485 PTZ Protocol: Select PTZ protocol, choose from the following protocols: Transparent, Pelco_D, Pelco_P, Everfocus or Samsung. (Note: All cameras on the RS-485 bus must use the same protocol) 485 ID: This is the ID used by the EKB500 to send commands to the mobile DVR. On an RS-485 connection, every device (PTZ, mobile DVR and controller) must be assigned an unique ID number between 0 and 127.
6.8.6 EKB200 Setting You can connect an EKB200, which is EverFocus’ USB keyboard, to the USB port on the DVR to control the Iris, focus or the pre-configured PTZ control functions of the connected cameras. For details on how to configure the PTZ control functions, including Preset Position, Auto Pan, Tour and Pattern, please refer to 4.1 PTZ Camera.
Page 144
EMV401 / 801 / 1601 Hybrid Mobile DVR 【Key No】 The control key number on the keyboard. 【Action】 Select an item from the drop-down list to define the function for each key on the keyboard. Set Preset: You can use the joystick on the keyboard to select a position and then press ...
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.8.7 Miscellaneous You can upgrade the latest firmware, restore the factory default settings to the mobile DVR, upload / save the mobile DVR configuration settings from / to the USB or change the language in this setup menu.
Page 146
EMV401 / 801 / 1601 Hybrid Mobile DVR Allowed Remote Reboot: Check the box to enable restarting the mobile DVR via the Network. Shutdown: Click the Shutdown button if you need to turn off the mobile DVR. When the message as below pops up on the screen, you can now turn off the mobile DVR.
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.9 Information You can see the mobile DVR information and Log data in this menu. Or export the log data to the USB storage device. 6.9.1 System In the System Menu, you can only see the information of the mobile DVR, Network or HDD.
Page 148
MAC 1 / MAC 2: Displays the MAC address of LAN 1 / LAN2. This option cannot be changed. mobile DVR Name: Displays the DDNS name if configured. Network ID: The ID number for EverFocus’ CMS as set up in the Alarm Server menu. 【Status】...
EMV401 / 801 / 1601 Hybrid Mobile DVR 6.9.2 You can choose, display or export log data using this menu. Start Date / End Date: Click to bring up the on-screen keyboard to set up the start / end date.
EMV401 / 801 / 1601 Hybrid Mobile DVR Chapter 7. Remote Access to the Mobile DVR Accessing the Mobile DVR on the Network Follow the steps below to access the mobile DVR from a computer. Open an Internet Explorer window and in the address bar type the IP address.
Page 151
EMV401 / 801 / 1601 Hybrid Mobile DVR When first connecting to the mobile DVR’s IP address, the following dialog may appear. Please check the “Always trust content from this publisher” box and click the Run button to run the EverFocus Viewer application.
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.2 Install JAVA Runtime You need to install the latest JAVA software for stable operation. 1. When first connecting to the mobile DVR’s IP address, the following dialog will show up if you didn’t install the JAVA software or its latest version on your computer.
Page 153
EMV401 / 801 / 1601 Hybrid Mobile DVR 6. Scroll to “Check for certificate revocation using”, and select the Online Certificate Status Protocol (OCSP). Also, check Place JAVA icon in system tray in “Miscellaneous” option. 7. Scroll to “Default JAVA for Browser” and check Mozilla family.
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.3 Browser Security Setting 7.3.1 Installing ActiveX Controls Follow the steps below to install the ActiveX Controls when you first connect to the mobile DVR’s IP address. If you do not see the images below, your security settings may be too high.
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.3.2 Enabling ActiveX Controls Note this section is only necessary if you DO NOT see the image (in the step 1 of 7.3.1 Installing ActiveX Controls) popping up when you first connect to the mobile DVR.
Page 156
EMV401 / 801 / 1601 Hybrid Mobile DVR 3. In the Security Settings window, scroll to “ActiveX controls and plug-ins”. Set the controls as follows: “Enable”: Allow previously unused ActiveX controls to run without prompt (Internet Explorer 7 only) ...
Page 157
EMV401 / 801 / 1601 Hybrid Mobile DVR 5. Close the window so you are back at the login screen. 6. Click the Refresh button to reload the page. 7. You may need to run the EverFocusViewer application when prompted to do so.
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.4 Remote Live View No. Name Description Menu Bar For configuring the mobile DVR. Please refer to 4. OSD Root Menu. Layout Click a desired layout. Sub / Main Click to switch between the Main stream and Sub stream.
Page 159
EMV401 / 801 / 1601 Hybrid Mobile DVR Black Circle: Indicates the mobile DVR is recording in sub-stream. Red Circle: Indicates the mobile DVR is recording in main-stream. White: Indicates the live view is in a normal status. Status Highlight Orange: Indicates a motion is being detected.
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.5 Menu Bar No. Name Description Live View Click to display the live view window. Camera Click to configure the camera settings. Please refer to 6.1 Camera. Click to configure the record settings. Please refer to 6.2 Record &...
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.6 How to Add Camera from Remote Side You can add IP cameras automatically by search or manually in these settings, and you can configure the settings for each analog and IP cameras. Other settings are similar with settings in the local OSD menu, so please refer to Chapter 6.
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.6.1.1 Manually Add an IP Camera from Remote Side 1. On the channel which you want to add an IP camera, click to select IP from the Type option, and click the Add button.
Page 163
EMV401 / 801 / 1601 Hybrid Mobile DVR 4. You can just click Save to add this camera, or you can also configure the detailed settings before saving. Click Cancel to return to the previous setting. 【 Main / Sub Stream Parameter 】 You can separately configure the settings for the Main / Sub Streams.
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.6.1.2 Add an Configure an Analog Camera from Remote Side 1. On the channel which you want to connect and display an analog camera, click to select the Analog from the Type option.
Page 165
EMV401 / 801 / 1601 Hybrid Mobile DVR Analog Camera Settings: Camera: Select a camera to be configured. Title: Click to bring up the on-screen keyboard for assigning a title for the selected camera. Each title supports up to 16 characters.
Page 166
EMV401 / 801 / 1601 Hybrid Mobile DVR Normal Speed: Select a frame rate per second (FPS) for continuous recording. The speed is limited by the maximum total recording capacity of the mobile DVR as allocated across all the installed cameras, with upper limit of 30 FPS (NTSC) / 25 FPS (PAL) per individual camera respectively(real time recording).
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.6.2 Auto Search This function allows you to automatically search and add the IP cameras connected in the same LAN network. Please see the steps below. 1. Before using the Auto Search function, you need to configure which channels you want to display IP camera live view from the Camera Status setting page, please refer to 7.6.1...
Page 168
EMV401 / 801 / 1601 Hybrid Mobile DVR 2. On the Auto Search page, click the Search button, and the IP cameras connected in the same network will show up in the Camera List. 3. To add cameras, there are two methods: A.
You can use the PTZ Control Panel to control the connected PTZ cameras, to set Preset setting and to activate the configured PTZ settings. You can also connect to an EverFocus’ EKB200 keyboard to a computer to control the PTZ camera.
Page 170
EMV401 / 801 / 1601 Hybrid Mobile DVR 8. Shortcut for Preset 1 ~ 9: a. Click digit 1 ~ 9 button without clicking any other buttons. b. The camera will seek that Preset Position. 9. To delete a Preset Position (if supported by the camera): a.
EMV401 / 801 / 1601 Hybrid Mobile DVR 7.8 Remote Playback To playback the recordings remotely, click the Search button on the Menu Bar. Click Time Search, Event Search or Smart Search and then set up the settings. For more details about Search setting, please refer to 5.3 Searching the Recordings for Playing Back.
EMV401 / 801 / 1601 Hybrid Mobile DVR Chapter 8. Specifications Model EMV1601 EMV801 EMV401 16 CH (Max: 8 IP Analog + IP Camera 8 CH 4 CH cameras) System Operating System Linux RAM Memory G-Sensor 3-Axis G-Sensor embedded System Control...
Page 173
3.65 Kg / 8.05 lbs (with mounting bracket) Weight 3.2 Kg / 7.05 lbs (without mounting bracket) Regulatory Regulatory CE, FCC, EN50155, E-Mark, RoHS-compliant * 3G USB dongles tested by EverFocus include Huawei E161 / E173 / E180 / E220.
Page 174
10 / 100 / 1000 Mbps (RJ45) Web Browser Windows (IE 8, 9, 10, Chrome, Firefox), MAC (TBD) 1. EverFocus’ CMS: Genie XMS xFleet (Server System) and EF xFleet Lite (Windows AP) Other Remote 2. EverFocus’ mobile app: MobileFocus for iOS and Android devices...
EMV401 / 801 / 1601 Hybrid Mobile DVR Chapter 9. Troubleshooting If you have problems with the system, run through the following checklist to see if you can solve the problem. The mobile DVR will not go into record mode.
EMV401 / 801 / 1601 Hybrid Mobile DVR Appendix Appendix A: Network Overview This chapter will give you a basic instruction on how to set up the mobile DVR for network connection. It is highly recommended that you have a working knowledge of what a network is and how it works.
EMV401 / 801 / 1601 Hybrid Mobile DVR Gateway Address Addressees are either local or remote. A gateway address is composed of four octets separated by decimal points. The gateway address is used to uniquely identify the device on the LAN that has access to the communications links connecting to other LANs, WANs and/or the Internet (access to the ‘remote’...
Page 178
This makes it much simpler to host a website, email server, or other type of server connection. Everfocus suggests using a static IP address. If this is not available, you will need to use a dynamic IP address. This is explained below.
Page 179
If the ports were changed in the Network Setup, use those port numbers. Pre-Installation EverFocus’ mobile DVR can operate using one of three types of networking connections. Simple One to One Connection: A simple one to one connection is the simplest type of network connection.
EMV401 / 801 / 1601 Hybrid Mobile DVR Appendix Appendix B: Linksys & D-Link Port Forwarding Typical Linksys Port Forwarding This section will cover a few simple configurations for the Linksys router. This chapter is only to offer some help to the installer and end user. Please understand we DO NOT support this product and will not give tech support on it.
Page 181
EMV401 / 801 / 1601 Hybrid Mobile DVR Click on the “Applications & Gaming” tab. Applications and Gaming allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Some Internet applications may not require any forwarding) To forward a port, enter the information on each line for the criteria required.
Page 182
EMV401 / 801 / 1601 Hybrid Mobile DVR Typical D-Link Port Forwarding This section will cover a few simple configurations for the D-Link router. This chapter is only to offer some help to the installer and end user. Please understand we DO NOT support this product and will not give tech support on it.
Page 183
EMV401 / 801 / 1601 Hybrid Mobile DVR Click Virtual Servers on the left to bring up the following screen. Virtual Servers allows users who are connecting remotely to access services on the router’s Local Network. The functions of each field are described below.
EMV401 / 801 / 1601 Hybrid Mobile DVR Appendix Appendix C: Timing of Alarm Modes Transparent Mode Input Event Alarm Duration Event = Reaction Duration of alarm input source (contact, system events...) Event : Resulting duration for this alarm mode, related to event record, alarm outputs, OSD...
Page 185
EMV401 / 801 / 1601 Hybrid Mobile DVR Timeout Mode Input Event Alarm Duration Event Duration = Reaction Duration of alarm input source (contact, system events...) Event : Alarm duration for timeout, defined in the event setup menus Duration : Resulting duration for this alarm mode, related to event record, alarm outputs, OSD...
Page 186
EMV401 / 801 / 1601 Hybrid Mobile DVR Timeout Mode: Retrigger of Alarms Duration of alarm input source (contact, system events...) Event : Alarm duration for timeout, defined in the event setup menus Duration : Resulting duration for this alarm mode, related to event record, alarm outputs, OSD...
EMV401 / 801 / 1601 Hybrid Mobile DVR Appendix Appendix D: Express Setup Recording Value Selection Rules Case 1: Record Mode: Normal + Event Record With: Recording days The mobile DVR will Auto adjust image Quality and Event frame rate to match the number of...
Page 188
EMV401 / 801 / 1601 Hybrid Mobile DVR Case 3: Record Mode: Normal + Event or Event Only Record With: Preset Setting Mobile DVR will apply the settings in the table below to all cameras according to the Preset Settings.
EMV401 / 801 / 1601 Hybrid Mobile DVR Appendix Appendix E: IR Remote Control The IR remote control is an accessory to enhance the convenient operation of the mobile DVR. You can perform all the settings and operations from the remote control. The effective distance is up to 33 feet line of sight.
Page 190
TEL: +91 22 6726 4500 FAX: +91 22 6726 4518 www.everfocus.in sales@everfocus.in Ihr EverFocus Produkt wurde entwickelt Your EverFocus product is designed and und hergestellt mit qualitativ manufactured with high quality materials hochwertigen Materialien und and components which can be recycled Komponenten, die recycelt und wieder and reused.