Advertisement
Table of Contents
- 1 Information
- 2 Table of Contents
- 3 List of Accessories
- 4 Assembly Instructions
- 5 Control Unit Installation
- 6 Connecting the Kit with Teleco TV TY2
- 7 LNB Rotation for Ideal Signal Reception in Extreme
- 8 Tips on the Best Use of Flat Sat Elegance Smart
- 9 Fault Display
- 10 Troubleshooting
- 11 Technical Specifications
- 12 Installed Kit
- Download this manual
Advertisement
Table of Contents
Related Manuals for Teleco Flat Sat Elegance Smart 50
Summary of Contents for Teleco Flat Sat Elegance Smart 50
- Page 1 Installation and operation manual...
-
Page 2: Information
Web site: www.telecogroup.com Technical attendance: 899.899.856 TELECO .p.a. declines all responsibility for any errors contained in this manual. All the contained information are up to the dates of printing and of the above-mentioned software revisions. TELECO .p.a. reserves the right to introduce any modification made necessary by... -
Page 3: Table Of Contents
Connecting the Kit with Teleco TV TY2 ................11 LNB rotation for ideal signal reception in extreme ...............12 Tips on the best use of Flat Sat Elegance Smart ...............14 Operating the Kit with Control Unit and TELECO TV TY2 ..........16 Fault display ........................19 Troubleshooting ........................21 Technical specifications .......................22... -
Page 4: List Of Accessories
List of accessories Flat Sat Elegance Smart is delivered inside a cardboard case that has been specially made to protect it from knocks and pressure. The following accessories are supplied: External motor-driven unit 50-65-85 cm dish Universal LNB Control Unit Motor connecting cable extension Coaxial cable extension for antenna signal Power Supply Cable... - Page 5 Important notice Flat Sat Elegance Smart is packaged in two separate cartons for transport reasons: a) the first package contains the driving unit with all the cables, and the control box. b) the second package only contains the dish. • It is important to check that the dish has not been damaged during transport when the package is opened.
-
Page 6: Assembly Instructions
(Fig. 2). Driving direction of the vehicle Flat Sat Elegance Smart 50 - 90 cm Flat Sat Elegance Smart 65 - 140 cm Flat Sat Elegance Smart 85 - 160 cm 2) Clean the roof carefully in the area the OUTSIDE UNIT is to be installed in. - Page 7 When they are present, remove the transparent films from the BASE PLATE (Fig. 5). 4) Clean the lower part of the BASE PLATE carefully, applying a layer of glue on the whole surface (e.g. SIKAFLEX). 5) Fasten the BASE PLATE to the roof (short side towards the vehicle driving direction). 6) Apply a layer of silicone all around the BASE PLATE in order to make it completely waterproof (Fig.
- Page 8 2) Fasten the external powered unit to the four stud bolts of the plate, using the four nuts supplied with the equipment. Caution: to ensure ideal nut tightening and prevent possible pin breaks, tighten the nut with a torque wrench set to 8 Newtons/metre Connection with extension WARNING The Grey and Black cables coming out of the Outside Unit are generally long enough to allow for connection to the Control Unit.
-
Page 9: Control Unit Installation
Control Unit Installation Control Unit 1) Position the in an easy accessible, ventilated compartment. WARNING: Control Unit Do not install the in areas where liquids can be spilled, since this could cause irreparable damage. Control Unit Do not install the in very small, unventilated compartments, since overheating could compromise its functionality and render the warranty null and void. - Page 10 Flat Sat Elegance Smart – Control Unit front View 1) Power-on indication LED Flat Sat Elegance Smart – Control Unit rear View 1) F type connector – input from LNB converter of the driving unit 2) F type connector – signal output to be connected to any satellite receiver 3) B type USB connector –...
- Page 11 Connection diagrams 1) Connect the grey cable (motors) to the MOTOR UNIT connector and the white coaxial cable (antenna) to the LNB connector of the Control Unit. 2) Connect the BLACK cable of the Control Unit to the NEGATIVE POLE of the vehicle 12 Volt Battery and the RED cable to the POSITIVE POLE + (remember not to mix the + and - poles up), using 2 cables of 2.5 mm2 cross section.
-
Page 12: Connecting The Kit With Teleco Tv Ty2
Connecting the Kit with Teleco TV TY2 Black Grey The GREEN safety cable of the Control WARNING: Unit must be connected to the consensus of the vehicle startup console (in many cases such The 3-way power connector (P) must only be consensus is located on Pin 15 in the inserted in the 12 Vdc POWER socket. -
Page 13: Lnb Rotation For Ideal Signal Reception In Extreme
WARNING This technical note is to call the attention of the installation personnel to certain details of Flat Sat Elegance Smart installation. During installation, you must take the following precautions: The power supply cable must directly come from the battery and must have no junctions. Minimum cross section of the cable is 2,5 mm . - Page 14 LNB tilt adjustment 1) Remove the LNB protective cover by screwing out the 3 screws 2) Loosen the screws on the LNB locking U-bolt 3) Turn in the Clockwise (West) or Anti-clockwise (South-East) direction 4) Lock the LNB again by screwing down the screws 5) Close back the LNB protective cover and screw...
-
Page 15: Tips On The Best Use Of Flat Sat Elegance Smart
Tips on the best use of Flat Sat Elegance Smart When you park your vehicle, make sure that: 1) No obstacle (for example trees) is too near your antenna, preventing it from moving freely. No metal or glass wall is very near (about 5 m) the antenna, since this would act as a mirror for satellite signals and could induce the antenna to stop towards it. - Page 16 Flat Sat Elegance Smart will automatically seek out the satellite transmitting it! To use the “Smart” function the Flat Sat Elegance Smart must be associated with a Teleco TY2/19D, TY2/22D, TY2/24 or TY2/32 TV with incorporated satellite receiver.
- Page 17 Switching on the Flat Sat Elegance Smart To switch on the Flat Sat Elegance Smart system press the AUTO key (1) for about 1 second. The Control Unit and TV will come on and the initialisation process begins. Satellite selection The Flat Sat Elegance Smart will automatically select the satellite transmitting the programme that has been entered on the receiver incorporated in the TV.
- Page 18 A few seconds later the satellite search menu disappears and the TV automatically displays the channel that was selected on the DVB-S2 satellite receiver incorporated in the TV. If you change channel on the receiver and choose a TV programme transmitted by a different satellite, the Flat Sat Elegance Smart will immediately start searching for the new satellite.
-
Page 19: Fault Display
To switch the system back on just press the key (1) again. Safety connection: correct connection of the green safety wire ensures that the antenna is automatically closed and the TV switched off if the vehicle starts moving. Make sure the green cable has been connected as indicated in the installation guide. Using the TV to watch other sources (terrestrial digital, DVD etc.) Use the INPUT (3) key on the remote control to select the source you intend to view on the TV. - Page 20 The raising motor is jammed. Make sure that no foreign matters hinder regular movement. The rotation motor is jammed. Make sure that no foreign matters hinder regular movement. During the switch-on stage a fault occurred in the driving motor. Make sure that no foreign matters hinder regular movement.
-
Page 21: Troubleshooting
Troubleshooting for Kit with control unit and TELECO TV TY2 If the control unit does not turn on by pressing the button (1) check the following: a) Are the RED and BLACK cables properly connected to the battery? The RED cable must be on the + pole, the BLACK cable on the - pole. -
Page 22: Technical Specifications
< 10 mA Fuse Dimensions 160 x 187 x 58 mm (Control Unit) Weight Control Box: ~1 kg external driving unit: Flat Sat Elegance Smart 50: ~8,8 kg Flat Sat Elegance Smart 65: ~9,0 kg Flat Sat Elegance Smart 85: ~10,8 kg... - Page 23 Flat Sat Elegance Smart 50...
- Page 24 Q.tà Description 11491 N.1 Dish support mast - 50 06681 N.1 Parabolic antenna D=500 mm 13721 N.1 Flat Sat Elegance Smart 50 Dish sticker 03685 N.4 Self-locking nut M5 UNI7474 10425 N.4 Screw M5x10 UNI 7687 INOX 10533 N.1 Engine cover 10442 N.2 Self-locking rivet SR-5105-W...
- Page 25 Flat Sat Elegance Smart 65 85...
- Page 26 Flat Sat Elegance Smart 65 85 Code Q.tà Description 11440 N.1 Dish support mast - 65/85 03676 N.1 Parabolic antenna D=650 mm 07364 N.1 Parabolic antenna D=850 mm 13721 N.1 Flat Sat Elegance Smart 65/85 Dish sticker 03684 N.4 Self-locking nut M6 UNI 7474 10910 N.4 Stainless stell screw M6X12 10533 N.1 Engine cover 10442 N.2 Self-locking rivet SR-5105-W...
- Page 28 Tav 2 Code Q.tà Description 11161 Wiper motor 04761 Waterproof microswitch 05086 Screw M3x20 galvanized 06817 Flat washer D=3 UNI6592 galvanized 11088 Screw M4x8 galvanized 12945 Connector strip 05807 mt. 3,6 Coax cable RG 58 12294 10-core 2,5mt Motor cable w/connector 12699 FF13 double female jack 15077...
- Page 29 Code Q.tà Description 09705 5A Fuse Code Q.tà Description 01458 Support 09318 Power supply cable 15922 Control unit lid 15921 T0331 board Smart 15923 Control unit bottom 13764 Cable Jack-Jack 2,0 mt. 09835 Black rubber foot 14707 RCA-Mini AV cable, 2.0 m long 15632 T0215 board Smart...
- Page 30 Code Q.tà Description 05950 3 m coax cable F/F.connector 03598 Shrink-wrap sheath 03597 Shrink-wrap sheath 09300 10-core 3mt engine unit cont. cable w/connector 10969 Cable cover abs 13190 PG completo di gommino 2 cavi 07883 9 m coax cable F/F.connector 08998 2 m coax cable F/F.connector 07294...
-
Page 31: Installed Kit
Via Majorana nr. 49, 48022 Lugo ( RA ) Declares under its own responsibility that the following products: Flat Sat Elegance Smart 50 - Flat Sat Elegance Smart 65 Flat Sat Elegance Smart 85 which are the subject of this certificate, conform to the following norms:... - Page 32 29 - 10 - 2014...