Advertisement
Quick Links
Advertisement
Related Manuals for Teleco VoyagerG3 65
Summary of Contents for Teleco VoyagerG3 65
- Page 1 INSTALLATION GUIDE AND USER MANUAL...
- Page 2 Web site: www.telecogroup.com Technical attendance: 899.899.856 TELECO .p.a. declines all responsibility for any errors contained in this manual. All the contained information are up to the dates of printing and of the above-mentioned software revisions. TELECO .p.a. reserves the right to introduce any modification made necessary by...
-
Page 3: Installation Instructions
Installation instructions Caution: Mount the antenna away from the vehicle roof edge to avoid overhanding the roof line when travelling. The Voyager G3 antenna must be installed near a vertical wall where the wall outlet can be fitted Set the drilling jig in place. Drill in the middle of the jig (page 14) …and then drill the outside wall. - Page 4 Insert the mast roof mounting bracket in Fasten the ring nut using self-tapping the dia. 42 hole bored in the roof, making screws. Place the rubber gasket over the sure you apply a layer of silicone under ring nut. ( Screws not supplied ) the ring nut.
- Page 5 Spread a thin film of Vaseline inside the Tight the locking ring nut seal and introduce the mast This mast locking device must be screwed tight every time you wish to secure the antenna in the desired position. To turn or lift the mast, loosen this ring nut.
- Page 6 Caution: Extend the dish mast all the way as shown in the figure Tighten the indicator screw hard, to the Insert the cable in the plastic handle hole end of the thread as shown in the figure.
- Page 7 Before fitting the plastic handle in the Make sure that the cable runs in front tube, make sure that the holes A and C of the pointer reference mark B are aligned with the reference mark B Using the Force the screw, fasten flexible tongues the plastic...
- Page 8 Lower the dish until the right travelling position is reached. Fix the steel plate to the roof with cement or both-sides adhesive tape under the LNB spacer Make sure that the antenna is exactly in its stowed position. Place the sticker on the mast in such a way that you can...
- Page 9 INSTRUCTIONS FOR USE 1) Prepare your satellite receiver and television for reception by following the relevant manufacturers’ instructions. 2) It is critical to make sure that there are no obstacles (e.g. houses, trees etc.) between the antenna and the satellite southwards. 3) Check in the table supplied the elevation relative to the town closest to the place where you are located.
- Page 10 LNB rotation for ideal reception in Europe’s extreme (South-West or South-East) areas Remember that the outside converter (a.k.a. LNB) has its own assembly position which must be complied with. Otherwise you will not receive any signal. The pre-set mounting position for the LNB is along the centre line of the disk (fig.
- Page 11 Dish Elevation Angle Charts To obtain dish pointing to your required satellite, it is essentially important to incline the dish to the correct angle. Check your position on the map, then set your dish elevation angle to the value in degrees read on the map for your required satellite.
- Page 12 Voyager elevation to locate satellites in Europe Country Town HOT BIRD ASTRA ATLANTIC TURKSAT ARABSAT 13° EST 19° EST BIRD 3 - 5° WEST 42° EST 26° EST AUSTRIA Innsbruck Salzburg Vienna BELGIUM Antwerp Brussels Gand Liege DENMARK Copenhagen FINLAND Helsinki FRANCE Lyon...
- Page 13 Pos. Code Description Q.ty Pos. Code Description Q.ty 03676 Parabolic antenna D=650 mm 12986 F50 F connector 07364 Parabolic antenna D=850 mm 15718 LNB Stark S1 10910 Screw M6X12 UNI 7687 10283 LNB PLASTIC CLAMP 03684 Self-locking nut M6 UNI 7474 10548 LNB PLASTIC TOP 10998...
- Page 14 Pos. Code Description Q.ty Pos. Code Description Q.ty 03605 Tear rivet 10968 Supporting tube 05799 Arm locking dowel 02125 Nut- M6x1,5 UNI 5588 07446 Arm locking screw 02354 Fastening bracket 11200 Reduction gear 02018 Lock UNIT KNOB 11805 Trilobed screws 5X12 02083 Self-tapping screws 03244...
-
Page 15: Conformity Certificate
Cut-out drawing mounting position in 1:1 scale CONFORMITY CERTIFICATE The manifacturer Teleco Spa Via Majorana nr. 49, 48022 Lugo ( RA ) Declares under its own responsibility that the following products: VOYAGER G3 50 which are the subject of this certificate, conform to the following norms: EN 60065: 2002 - EN 55013: 2001 + A1: 2003 - EN 61000 –... - Page 16 26/09/2014...