Related Manuals for Pheonix Model Extra 330SC
Summary of Contents for Pheonix Model Extra 330SC
- Page 1 I n s t r u c t i o n M a n u a l Wingspan : 1850mm (72.83 inches) Length : 1842mm (72.52 inches) Weight : 5900g Radio : 6 channel with 5 high torque servo + 1 standard servo Engine : Gas 25cc - 35cc...
-
Page 2: Kit Contents
Instruction Manual EXTRA 330SC KIT CONTENTS: We have organized the parts as they come out of the box for better identification during assembly. We recommend that you regroup the parts in the same manner. This will ensure you have all of parts required before you begin assembly. -
Page 3: Tools And Supplies Needed
1. Please trial fit all the parts. Make sure you have the correct parts and that they fit and are aligned properly before gluing! This will assure proper assembly. EXTRA 330SC is hand made from natural materials, every plane is unique and minor adjustments may have to be made. -
Page 4: Installing The Control Horns
Instruction Manual EXTRA 330SC ↑ To the cowl Collar 4. Tie the string from inside the wing to the end of 6. Repeat step # 1 - # 5 to install the second the servo wire. Pull the servo wire through the aileron servo in the opposite wing half. -
Page 5: Installing The Aileron Linkages
Instruction Manual EXTRA 330SC 2. Install the link ball to the control horn. M3 nut control 4. Repeat step # 1 - # 3 to install the control horn for the second aileron. ↑ To the cowl Screw Flat washer... -
Page 6: Installing The Elevator Servo
Instruction Manual EXTRA 330SC INSTALLING THE WING TO THE FUSELAGE Attach the wings to the joiner tube and using the nylon thumbscrews to secure the wing panels to the fuselage. Plastic screw 3. Remove the covering from the elevator to install the control horn. -
Page 7: Installing The Elevator Linkages
Instruction Manual EXTRA 330SC INSTALLING THE HORIZONTAL STABILIZER INSTALLING THE ELEVATOR LINKAGES The elevator linkages are assembled as shown below 1. Remove the covering from the fuselage. Remove the covering 22mm 22mm 40mm . Repeat these step as installing the aileron linkages. -
Page 8: Installing The Vertical Stabilizer
Instruction Manual EXTRA 330SC INSTALLING THE VERTICAL STABILIZER INSTALLING THE RUDDER LINKAGES The rudder is controlled by two metal cables. 1. Remove the covering from the bottom of the Install the rudder linkages and cables as below. rudder. 1. Use a hobby knife to remove the covering from the openings for the rudder control cables. -
Page 9: Installing The Tail Wheel
Instruction Manual EXTRA 330SC Aluminum ball Crimp Cable M3 Clevis Crimp Plastic ball link Cable end Metal connector INSTALLING THE TAIL WHEEL 5. Thread the metal connector to the link ball. 1. The tail wheel set. 2. Remove the covering. -
Page 10: Installing The Wheel Pants
Instruction Manual EXTRA 330SC 4. Secure the tail brace to the fuselage. INSTALL THE GEAR COVER Screw 5. Connect the spring. INSTALLING THE WHEEL PANTS 1. Locate the wheel pants from the hardware bag. Mark the locations of the mounting axles onto the wheel pants. -
Page 11: Installing The Engine
Instruction Manual EXTRA 330SC 4. Carefully bend the third nylon tube down at a 45 degree angle (using a cigarette lighter). This tube will be vent tube to the fueling valve When the stopper assembly is installed in the tank, the top of the vent tube should rest just below the top surface of the tank. -
Page 12: Installing The Throttle Servo
Instruction Manual EXTRA 330SC 2. Slide the cowl back into place. Align the front of the cowl with the crankshaft of the engine. The front of the cowl should be positioned so the crankshaft is in the middle of the precut opening. -
Page 13: Lateral Balance
Instruction Manual EXTRA 330SC 2. Mount the wing to the fuselage. Using a couple of pieces of masking tape, place them on the top side of the wing 130mm back from the leading edge, at the fuselage sides. 3. Turn the airplane upside down. Place your fingers on the masking tape and carefully lift the plane. - Page 14 EXTRA 330SC 3-D PERFORMANCE SETTINGS LOW RATE Ailerons : 15mm up 15mm down EXTRA 330SC will perform 3-D aerobatics easily if you use the largest engines Elevator : 15mm up 15mm down recommended within the engine range. If you Rudder : 35mm right 35mm left setup your airplane to do 3D maneuvers, you will need to be throttle conscious;...
- Page 15 I/C FLIGHT WARNINGS Always operate in open areas, away Keep all onlookers (especially small from factories, hospitals, schools, THE PROPELLER IS DANGEROUS children and animals) well back from buildings and houses etc. NEVER fly Keep fingers, clothing (ties, shirt the area of operation. This is a flying your aircraft close to people or built sleeves, scarves) or any other loose aircraft, which will cause serious...
- Page 16 I/C FLIGHT GUIDELINES Operate the control sticks on the When ready to fly, first extend the transmitter and check that the control transmitter aerial. surfaces move freely and in the ALWAYS land the model INTO the CORRECT directions. wind, this ensures that the model lands at the slowest possible speed.