Panasonic WV-CZ362E Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Security Camera
  5. WV-CZ362E
  6. Operating instructions manual
Panasonic WV-CZ362E Operating Instructions Manual

Panasonic WV-CZ362E Operating Instructions Manual

Color cctv camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Operating Instructions

Color CCTV Camera
WV-CZ362E
Model No.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.

Advertisement

Table of Contents
loading

Related Manuals for Panasonic WV-CZ362E

Summary of Contents for Panasonic WV-CZ362E

  • Page 1: Operating Instructions

    Operating Instructions Color CCTV Camera WV-CZ362E Model No. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.

  • Page 2: About The User Manual

    ABOUT THE USER MANUAL The operating instructions of the camera consist of 2 sets: these operating instructions (PDF) and Installaion Guide. This document explains how to configure the settings of the camera. Refer to the installation guide fo further information about how to install the camera. ...

  • Page 3: Table Of Contents

    CONTENTS ABOUT THE USER MANUAL ..........2 TRADEMARKS AND REGISTERED TRADEMARKS .

  • Page 4: Setup Menu

    SETUP MENU Performing each setting item in the setup menu should be completed in advance to use this unit. Perform the settings for each item in accordance with the conditions of the camera shooting area. Refer to the Operating Instructions (PDF) for further information. List of setup menu Setup item Description...
  • Page 5 Basic operation The description below explains how to operate the setup menu basically. The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor. Refer to the installation guide for further information about the operation buttons.

  • Page 6: Setting Procedure

    SETTING PROCEDURE Hold down the setting button for approx. 2 seconds to call up the top screen of the setup menu. ** WV-CZ362 SETUP ** CAMERA PRESET POSITION SPECIAL COMMUNICATION PASSWORD LOCK OFF When the setting button is pressed for each item, each setting can be made. Setting can not be made if ON setting has been made for PASSWORD LOCK.

  • Page 7: Camera Setting

    Camera Setting To Display the Camera Setup Menu Move the cursor to CAMERA , and press the setting button. The CAMERA SETUP menu appears. ** CAMERA SETUP ** 1/2 CAMERA ID ALC/MANUAL SHUTTER AUTO ON(MID) SENS UP SYNC WHITE BAL ATW1 MOTION DET LOW2...
  • Page 8 To determine the display position of the CAMERA ID 1. Move the cursor to POSI, and press the setting button. The display in the figure appears and the CAMERA ID is highlighted. 2. Move the CAMERA ID to the desired position. 3.
  • Page 9 (2) ALC Mode with BLC OFF 1. Move the cursor to BLC and select OFF. (When you select MANUAL, BLC is not avail- able.) MASK SET appears on the menu. Blinking 2. To mask an area where backlight is bright, move the cursor to the area and press the setting button.
  • Page 10 5 Electronic Sensitivity Enhancement (SENS UP) The electronic sensitivity enhancement mode changes as follows: X2 AUTO X4 AUTO X6 AUTO X10 AUTO X16 AUTO X32 AUTO X2 FIX X4 FIX X6 FIX X10 FIX X16 FIX X32 FIX While the SENS UP function is selected, noise or spots may appear in the picture when the sensitivity of the camera is increased.
  • Page 11 8 Motion Detector Setting (MOTION DET) 1. Select ON or OFF. 2. If ON is selected, press the setting button. The MOTION DETECT menu appears. You can mask the areas in this menu. 3. Move the cursor to MASK SET and press the setting button. 48 mask areas appear on the monitor screen.
  • Page 12 Because the alarm signal is multiplexed on the video signal, it may be mistakenly interpreted by other video equipment as a time code signal. Therefore, when this camera is not used in a Panasonic Intelligent CCTV System, select OFF to prevent the above from occurring.
  • Page 13 HIGH: approximately 4 lx LOW: approximately 2 lx Note: When near-infrared lamps are used, the image may be displayed out of focus and mode switching may not perform automatically. 4. Move the “I” cursor to set DURATION TIME. The camera determines whether to switch the mode when the time set for holding a pic- ture motionless on the screen has elapsed.
  • Page 14 Zoom/Focus Press the SET and then UP, DOWN, RIGHT or LEFT button to adjust the Zoom and Focus positions. Position Press the SET and then UP, DOWN, RIGHT or LEFT button to set up the mask position of the privacy zone. Scale Press the SET and then UP, DOWN, RIGHT or LEFT button to set up the mask size of the privacy zone.

  • Page 15: Preset Position Setting

    Preset Position Setting ** PRESET POSITION ** PRESET HOME POSITION OFF SELF RETURN IMAGE HOLD RET TOP END 1 Preset Menu Display 1. Displaying the preset menu directly (1) Move the cursor to PRESET 1 and select the position number. (2) Press the setting button.
  • Page 16 A Position Setting (POSITION SET) 1. Move the cursor to POSITION SET on the preset setting menu and press the setting button. The POSITION setting menu appears. (1) Move the cursor to PUSH SET for ZOOM/FOCUS and press the setting button. ** POSITION 1 ** ZOOM/FOCUS PUSH SET...
  • Page 17 C Light Control Setting (ALC/MANUAL) Refer to Light Control Setting on page 8. D Auto Focus Setting (AF MODE) Refer to Auto Focus Setting on page 14. E Scene File Setting (SCENE FILE) 1. To set a scene file number Move the cursor to SCENE FILE and select a scene file number (1 to 10, or OFF).

  • Page 18: Special Setting

    Special Setting ** SPECIAL SETUP ** CHROMA GAIN ••••|•••• AP GAIN ••••|•••• PEDESTAL ••••|•••• PIX OFF ZOOM INVERSE FOCUS INVERSE REFRESH PUSH SET CAMERA RESET PUSH SET RET TOP END 1 Chroma Level (CHROMA GAIN) 2 Aperture Level (AP GAIN) 3 Pedestal Level (PEDESTAL) Move the cursor to CHROMA GAIN, AP GAIN and PEDESTAL and move the “I”...

  • Page 19: Communication Setting

    5 ZOOM INVERSE The TELE/WIDE operation from the lens control terminal or the UP and DOWN buttons is reversed during ON setting. 6 FOCUS INVERSE The FAR/NEAR operation from the lens control terminal or the UP and DOWN buttons is reversed during ON setting.

  • Page 20: Password Lock Setting

    Move the cursor to the item and select the parameter. Unit Number In an RS485 chain each unit must have a unique number. Sub Address Do not set. Baud Rate Specifies the transmission speed (2 400, 4 800, 9 600, 19 200 bit per second) for the RS485 communication.
  • Page 21 1. Move the cursor to PASSWORD LOCK. ** PASSWORD? ** 0 1 2 3 4 5 6 7 8 9 . . . ↑ RESET NEW PASSWORD RET TOP END Note: ON or OFF can be selected only after going through the password verification. OFF: You can change all settings.
  • Page 22 Importer's name and address to follow EU rules: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg F.R.Germany © Panasonic System Networks Co., Ltd. 2010 sF0409-2010 3TR006208CZB Printed in China...

Table of Contents