Advertisement
NOTE:
NOTE:
IF THE REAR SHROUD IS ASSEMBLED TO THE PARABODY 425,
IT WILL NEED "]70
BE REMOVED TO
ASSEMBLE THE LEG PRESS AND THE ADAPTER KIT.
PLEASE REMOVE THE SE[ROUD AT THIS TIME
BY REMOVING THE FOUR (4) 3/8 X 1 IN. BOLTS AND FOUR 3/8 IN. WASHERS.
THE LEG PRESS ATTACHMENT (832101)
MUST BE ASSEMBLED BEFORE ASSEMBLING IT TO THE
PAKABODY 425.
PLEASE ASSEMBLE THE LEG PRESS ATTACttMENT AT TIIIS
TfME USING THE 832
PRODUCT ASSEMBLY INSTRUCTIONS.
1.
Attach O, vo (2) 2 SQ. IN. COVER CAPS onto the FRONT LEG WELDMENT
as shown on drawing.
Remove two (2) I/2 FN'. LOCK NUTS and two (2) 1/2 IN. WASHERS FROM the PRESS BASE: \ 13ASE connection of the
425.
SECURELY assemble the BASE CONNECTION WELDMENT to the PRESS IIASE and BASF, connection
of the -12S
using the two (2) I12 IN. LOCK NUTS REMOVED IN STEP
o
SECURELY attach
the assembled
832 LEG PRESS ATTACHMENT to the FRONT LEG ~rELDMENT using two (2)
I/2 X 3 IN. BOLTS, two (2) I/2 IN. WASHERS
(~To, OMS'['EP 2) and two (2) I/2 IN. LOCK NUTS.
SECURELY attach
the 832 to the 425 by connecting
the FRONT LEG WELDMENT to the BASE CONNECTION
WELDMENT,
using two (2) I/2 X 3. IN. BOLTS, two (2) 112 IN. WASHERS
and two (2) I/2 IN. I_,OCK
Remove one (I) 1/4 .IN. CAP NUT from the rear L-hook of the TOP BOOM. (LEAVE 2 IN. PULLEY ON L-HOOK)
Assemble one (I) 2 IN. PULLEY to the rear L-hook and secure place ~vith one (I) 114 IN. CAP
CAREFULLY remove one (I)
318 IN. LOCK ~ and one (I)
SWIVEL WITH MULTI-PRESS SHOCK CORD from
rear fiat of the BASE.
o
I0.
Remove one 3/8 IN. NUT, one (I) 2-3/8 IN. CABLE RETAINING CLIP, one (1) 3-I/2 X 1 IN. PULLEY, one (1) Y/8
1/2 IN BOLT, and one (1) 3/8 IN. WASHER from the rear flat ofthe BASE.
Reassemble one (I) 3-112 x I IN. PULLEY, one (I) 2-318 IN. CABLE RETAINING CLIP, one 318
WASI
-IF_R,
and one
(I) 318 IN. NUT, from Step 9 to the rear fiat of the BASE using one (I) 318 x 4-I/2 IN. THREADED
STUD, and one (1)
318 IN. NLIT.
11.
12.
Reassemble one (1) SWIVEL WITH MULTI-PRESS SHOCK CORD to the 3/8 X 4-1/2 IN. TI-tl~AI)ED STUD, using
(I) 318 IN. LOCK Nq.JT. (PARTS ARE FROM STEP 8)
Assemble one (1) 3-1/2 x I IN. PULLEY to the flat facing the leg press on the BASE, and one (1) 3-1/2 IN. PULLEY to the
fiat on the FRONT LEG WELDM'ENT
using two (2) 3/8 x 2 iN. BOLTS, two (2) 3/8 IN. WASHEt~, two {2) 2-3/8
CABLE RETAINING CLIPS, and taro (2) 3/8 IN. LOCK NUTS.
13.
To assemble the LEG PRESS CABLE, follow lhe cable muting diagram and use the following steps:
Adjust the LEG PRESS so the seat is in its tightest pre-stretch position.
SECURELY attach
the loop end of the LEG PRESS CABLE to the FROIqr LEG WELDMENT
using one (I)
QUICK DISCONNECT LINg<.
~un the cable through the hole in the D-RING as showa in ('DETAIL A) and attach one {'I) KEYHOLE CLEVIS
to the end of the LEG PRESS CABLE.
12F21/95
Advertisement
