Download Print this page
ParaBody 415101 Assembly Instructions Manual
ParaBody 415101 Assembly Instructions Manual

ParaBody 415101 Assembly Instructions Manual

Leg press adapter kit

Advertisement

Quick Links

Serious Steel
415101
400 LEG PRESS ADAPTER KIT
ASSEMBLY INSTRUCTIONS
Part# 6694601
II
Revision: 06/12/97

Advertisement

loading

Summary of Contents for ParaBody 415101

  • Page 1 Serious Steel 415101 400 LEG PRESS ADAPTER KIT ASSEMBLY INSTRUCTIONS Revision: 06/12/97 Part# 6694601...
  • Page 2 Parabody customer service department at (800) 328-9714. Please note: * Thank you for purchasing the Parabody 415101 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them fbr future reference. Tl~:is product must be assembled on a flat, level surface to assure its proper function.
  • Page 3 1/2 X 3-1/4" BOLT 3102918 112-3/4" 6694301 6694401 82-1/2" (832101) must be assembled before connecting it to the HOME GYM STEP 2 ¯ Slide one 2" SQ. END CAP (6) into the BASE CONNECTION as shown in FIGURE 2. FIGURE 3 WASHER LOCKNUT...
  • Page 4 OPTION by unfastening the 3/8 X 4-1/2" BOLT holding the pulley on. See FIGURE 5. (Note: Save 3-1/2" PULLEY, it will be used in later steps.) (4) to the 400 HOME GYM using two 1/2 X 3-1/4" BOLTS FIGURE 5 3-1/2"...
  • Page 5 STEP 6 ¯ Attach CABLE SWIVEL (3) ADJUSTMENT TUBE on the 832 using the existing previously removed 3/8 X 4-1/2" BOLTS, WASHERS, 2" WHEELS AND NUT. (Note: Securely tighten, then back off 1/4 turn to allow the CABLE SWIVEL & WHEELS to rotate freely.) See FIGURE 6.
  • Page 6 FIGURE 8 REMOVE STEP 8 Remove the existing LAT CABLE (part #668701) using the following steps: ¯ Discolmect LAT BAR from TOP BOOM. ¯ Unscrew the threaded end of CABLE from the HEAD PLATE ASSEMBLY. ¯ Route the LAT CABLE around the PULLEY BLOCK as shown in FIGURE 8. ¯...
  • Page 7 FIGURE 9 STEP 9 Install the NEW 112-3/4" CABLE ASSY (16) using the following steps: ¯ Route the CABLE (16) through the TOP BOOM as shown in FIGURE 9. The pulleys in TOP BOOM may need to be temporarily removed to perform this step. (Note: Make sure the CABLE is running OVER the BOLTS connecting the FRONT UPRIGHT to the TOP BOOM.
  • Page 8 FIGURE 11 STEP 11 ¯ Attach the hook end of 82-1/2" CABLE (17) to the CABLE SWIVEL (3) with one QU]:CK DISCONNECT IMPORTANT: Tighten the QUICK DISCONNECT LINK (8) securely. ¯ Route the 82-1/2" CABLE (17) under the WEIGHT STACK as shown in FIGURE 11. IMPORTANT: Tighten QUICK DISCONNECT LINK...
  • Page 9 STEP 12 o Screw the threaded end of 82-1/2" CABLE (17) to the PULLEY BRACKET (2) as shown in FIGURE 12. 3/8X1-3/4" STEP 13 ¯ Attach one 3-1/2" PULLEY (5) to the FRONT LEG (1) and one 3-1/2" PULLEY (5) to the BASE CONNECTION 3/8 X 1-3/4"...
  • Page 10 PULLEY BRACKET (2) is held against the TOP BOOM and the cable is slightly Tighten the jan but securely. Next, thread the 82-1/2" CABLE (17) into the PULLEY BRACKET tighten the jam nut securely. THIS CONCLUDES THE ASSEMBLY OF THE 415101 LEG PRESS ADAPTER KIT pulling up on the HEAD PLATE.

This manual is also suitable for:

400