Related Manuals for ParaBody 445104
Summary of Contents for ParaBody 445104
-
Page 1: Assembly Instructions
445104 425 SECOND STACK OPTION ASSEMBLY INSTRUCTIONS Part # 6865201 Revision: 2/15/00... -
Page 2: Important Notes
2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. -
Page 3: Parts List
FIGURE 2 STEP 2 • REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the bottom of the front SHROUD & rear SHROUD. Remove the SHROUDS from the 425103 HOME GYM. See FIGURE 2. PARTS LIST PART #... - Page 4 HEAD D-RING PLATE CABLE (67250) FIGURE 3 STEP 3 • Unscrew the threaded ends of the HEAD PLATE CABLE from the WEIGHT STACK SHAFT & the D-RING and remove HEAD PLATE CABLE. The HEAD PLATE CABLE will be used later. See FIGURE 3. (NOTE: Remove pulleys for ease of removal.)
- Page 5 STEP 4 • Remove the PRESS CABLE (67249) from the KEYHOLE CLEVIS and ELASTIC CORD. (NOTE: The LAT or LEG EXT CABLE can be moved over one hole on the D-RING so the KEYHOLE CLEVIS are evenly spaced .) • Discard the KEYHOLE CLEVIS and ELASTIC CORD. FIGURE 5 3/8”...
- Page 6 FIGURE 6 3/8 X 1” 11 STEP 6 • (NOTE: STEP 6 is only if the 435101 LEG PRESS OPTION is installed otherwise proceed to STEP 7.) • Assemble the previously removed 2” PULLEY to the bracket on the TOP BOOM using one 3/8 X 1” BOLT (11), one previously removed 3/8”...
- Page 7 3/8 X 1/2” SPACER STEP 8 • Remove two 2” PULLEYS (5) to the rear bracket on the TOP BOOM using one 3/8” THREADED SHAFT (9), two 3/8” WASHERS, two 3/8” HEX NUTS (8), and two 3/8” LOCK NUTS (7) as shown in FIGURE 8. •...
- Page 8 FIGURE 10 PRESS CABLE (67249) STEP 10 • Carefully remove and discard the PRESS CABLE as shown in FIGURE 10.
- Page 9 FIGURE 11 PRESS-STACK CABLE (67475) STEP 11 • Route the new PRESS-STACK CABLE (5) around the pulleys and l-brackets as shown in STEP 11. (Remove pulleys for ease of installation.) PRESS- STACK CABLE (67475) FIGURE 12 STEP 12 • To assemble the PRESS-STACK CABLE (5) follow the cable routing as shown and use the following steps: •...
- Page 10 STEP 13 • Insert two WEIGHT PLATE BUSHINGS (17) into the top side of each of the fifteen WEIGHT PLATES (16) as shown in FIGURE 13. FIGURE 14 STEP 14 • LOOSEN the bolts holding the TOP BOOM to the UPRIGHTS. Bolts will have to be removed to install GUIDE RODS (1). See FIGURE 14.
- Page 11 14 3/8 X 1-1/4” FIGURE 15 STEP 15 • Insert four CAP PLUGS (9) into the top and bottom ends of the GUIDE RODS (1) as shown in FIGURE 15. • SECURELY assemble the WEIGHT STACK SHAFT (2) to the HEAD PLATE (4) using one 3/8 X 1-1/4” BOLT (14) and one 3/8” WASHER (10).
- Page 12 FIGURE 16 STEP 16 • CAREFULLY lift or tilt the TOP BOOM and insert all GUIDE RODS into the bushings. See FIGURE 16. • With the GUIDE RODS (1) securely held in the TOP BOOM. Tighten all TOP BOOM connections. (NOTE: Make sure the LAT CABLE runs over the top of the bolts in the TOP BOOM.) TOP BOOM TIGHTEN! (NOTE: Make sure...
- Page 13 STEP 17 • Screw one of the threaded ends of the previously removed HEAD PLATE CABLE approximately 1” into the end of the WEIGHT STACK SHAFT. See FIGURE 17. STEP 18 • Route the thread end of HEAD PLATE CABLE up and over the PULLEYS in the TOP BOOM above the WEIGHT STACK.
- Page 14 REAR SHROUD FIGURE 19 STEP 19 • The rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the plastic SHROUD as shown in FIGURE 19.
- Page 15 • The PRESS STATION and SWIVEL LOW PULLEY are now operated with the front stack and the LAT, PEC, and LEG STATION are now operated with the rear stack. Thank you for purchasing the Parabody 445104 Second Stack Option. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.