Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for King-Meter SW-LCD
Summary of Contents for King-Meter SW-LCD
- Page 1 KING-METER USER GUIDE SW-LCD...
-
Page 2: Table Of Contents
Contents 1. Preface ………………………………………….3 2. Appearance and Size……………………………4 2.1 Material and Color…………………………… 2.2 Display Size and Installation Size ………… 3. Function Summary and Button Definition…5 3.1 Preset and Default Items ……………………. 5 3.2 Display Figures ……………………………… 5 3.3 Button Definition…………………………..… 6 4. - Page 3 6.6 Push cruise control………… ………………...13 6.7 Turn On and Turn Off the Backlight…………14 6.8 Power of the Display……………………………… .14 6.9 Error Code Display………………………..15 7 . At t e n t i o n f o r U s i n g … … … … … . … … . 1 6 FAQ Answers…………………………………16 9.
-
Page 4: Preface
1、Preface Dear users, To ensure better performance of your e-bike, please read through the SW-LCD product introduction carefully before using it. We will use the brief words to inform you of all the details （including hardware installation, setting and normal use of the display）when using our display. -
Page 5: Appearance And Size
2、Appearance and Size 2.1 Material and Color SW-LCD housing material: PC. And the color of housing is white or black. Working temperature scope: -20℃—+60℃, the shell material can ensure normal use and good mechanical performance of the products. 2.2 Display Size and Installation Size（Unit：mm）... -
Page 6: Function Summary And Button Definition
3、Function Summary and Button Definition 3.1 Preset and Default Items SW-LCD user settings include: wheel diameter （ 18-28inch ） ; max speed; LCD backlight contrast; choice of display unit. 3.2 Display Figures: Display content: battery capacity, motor power ratio, riding speed, riding distance, power, PUSH cruise control, and error code display of the electronic control system. -
Page 7: Button Definition
SW-LCD is equipped with special 30-button unit. This operating button is suit for both L/R hand, button instruction figures as follows: 30-button unit is connected to the bottom of the SW-LCD display via lead cable. In the following introduction, is named as “MODE”. -
Page 8: Installation Instruction
4、Installation Instruction Fix the display and 30-button unit on the handlebar and adjust to an appropriate visual angle. Match display connector with controller connector. 5、Set up 5.1 Preparation for Starting the Display Make sure connector linked properly to the motor controller on the bike. -
Page 9: Max Speed
Press UP or DOWN to choose a right diameter（18-28inch） for the bike. Default set is 26 inch. After confirmation of wheel size, press MODE to reserve it and enter into the max speed set. 5.4 Max Speed The second setting parameter is Max Speed. The interface is as below: Re-set speed should be in accordance with the local regulation speed. -
Page 10: Backlight Brightness
factory is 25 Km/h. Speed option: 12-40Km/h, use UP or DOWN then confirm by MODE. Then enter into the interface of backlight brightness. 5.5 Backlight Brightness The third setting parameter is backlight brightness. The interface is as below: Press UP or DOWN to modify the backlight brightness. You can choose from level 1 to level 3. -
Page 11: Quit From Set Up
Press UP or DOWN to choose a display unit. The unit could be MPH or Km/H. The range unit will change accordingly with the speed unit. 5.7 Quit from set up In the setting state, press MODE for 3 seconds to confirm the input, save current setting and exit. -
Page 12: Speed Display (Current Speed/Average Speed/Max Speed)
battery segment will flash at 1 Hz. It indicates that the battery is severely low in voltage condition and needs to be recharged immediately. Low Voltage Flash 6.3 Speed Display (Current Speed/Average Speed/Max Speed) When the e-bike starts, the display will automatically show the current speed. -
Page 13: Assisted Power Select Or Throttle Level Select
The interface of switching speeds 6.4 Assisted Power Select or Throttle Level Select Press UP or DOWN to change the output power of the motor. The power ranges from Level 1 to Level 5. Level 1 is the minimum power. Level 5 is the maximum power. The default level is Level 1. -
Page 14: Distance Display
6.5 Distance Display (Riding Distance / Total Distance) Press MODE to switch between riding distance and total distance. This function is convenient for users to check the riding distance (TRIP) and the total distance (ODO). Range Interface 6.6 Push Cruise Control Press DOWN for a while to get into power assist mode, and the bike will travel at fixed speed 6Km/h. -
Page 15: Turn On And Turn Off The Backlight
SW-LCD backlight, when the surrounding light is not enough or it is in the evening. Hold both UP and MODE for 3 seconds again and you can turn off the SW-LCD backlight. When the backlight power ON, the headlight also power on (if the bike assembles with a headlight). -
Page 16: Error Code Display
6.9 Error Code Display If there is something wrong with the electronic control system, the display will show the error code automatically. The following is the definition of the error code. Code number Definition Abnormal current Throttle fault Motor phase problem Motor Hall defect Brake Failed Abnormal Communication... -
Page 17: At T E N T I O N F O R U S I N
Error Code Display Display return to normal only after problem being fixed and bike will not run before fixing the problem. 7、Attention for Using Ride your bike in a safe way. Don’t hit or knock the display. Keep away from the bad environments when use, such as downpour, large snowflakes and solarization. -
Page 18: Quality Warranty And Coverage
9、 Quality Warranty and Coverage We are not responsible for the scratched or broken shell after the products are delivered out of the factory. We don’t repair scratched or broken lead wires. The LCD display function warranty: 24 months from the delivery time of the display out of the factory.