Advertisement
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS
NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS
NÉCESSAIRES POUR L'INSTALLATION.
1. Before proceeding, familiarize yourself with the parts of the
Cross-Trainer and make sure that you have received all the
items described in the Component List.
2. Locate the left and right F
P
P
H
P
HILLIPS
AN
EAD
C
(9) to the F
OVER
RAME
to the F
in the same manner using two P
RAME
P
S
(3). Secure the tops of the F
OINTED
CREWS
together using two P
CAUTION: Do not overtighten the P
S
(3).
CREWS
3. Locate the R
U
IGHT
SER
(2PA) located at the bottom of the R
P
C
(2PB) positioned at the top of the R
IN
ONNECTOR
A
(B). Feed the connectors and excess cable up into the
RM
R
U
A
. Secure the R
IGHT
SER
RM
R
A
using three H
OCKER
RM
three I
T
NTERNAL
OOTH
for the L
U
A
EFT
SER
all screws securely.
CAUTION: Be careful not to pinch the W
assembling the U
SER
C).
4. Detach and unwrap the W
the top of the M
ONOCOLUMN
A
(7) with the handgrips facing upward, feed the W
SSEMBLY
H
up through the neck and out the top access hole.
ARNESS
Carefully lower the C
M
.
ONOCOLUMN
CAUTION: Be careful not to pinch the W
when assembling the C
M
(F).
ONOCOLUMN
5. Using two H
S
EX
OCKET
W
(8), secure the C
ASHERS
M
(F). Tighten the S
ONOCOLUMN
6. Insert the G
ROMMETS
S
A
. Locate the A
UPPORT
SSEMBLY
A
T
with the four holes on the C
CCESSORY
RAY
A
. Using four P
SSEMBLY
secure the A
CCESSORY
as shown. Tighten the S
CAUTION: Do not overtighten the P
S
(3).
CREWS
7. Remove the adhesive back and install the P
the C
(22).
UP
C
(9 &10). Using two
RONT
OVER
S
(3), mount the L
OINTED
CREWS
(A). Attach the R
IGHT
P
H
P
HILLIPS
AN
EAD
OINTED
HILLIPS
A
(12). Snap the 2-P
RM
U
IGHT
SER
U
A
IGHT
SER
RM
S
H
EX
OCKET
EAD
L
W
(18). Repeat the procedure
OCK
ASHERS
(11) and L
R
RM
EFT
OCKER
IRE
A
(11 &12) to the R
RMS
H
(E) (16P, 4P) located at
IRE
ARNESS
(F). Holding the C
S
A
ONSOLE
UPPORT
SSEMBLY
IRE
S
A
ONSOLE
UPPORT
SSEMBLY
H
C
S
(1) and two F
EAD
AP
CREWS
S
ONSOLE
UPPORT
securely.
CREWS
(20) into the four holes on the C
T
CCESSORY
P
H
P
HILLIPS
AN
EAD
OINTED
T
to the C
RAY
ONSOLE
securely.
CREWS
HILLIPS
IMPORTANT!
IMPORTANTES!
F
EFT
RONT
F
C
(10)
RONT
OVER
P
H
HILLIPS
AN
EAD
C
RONT
OVERS
S
(3).
CREWS
P
H
P
AN
EAD
OINTED
C
IN
ONNECTOR
A
into the 2-
RM
R
IGHT
OCKER
to the R
IGHT
C
S
(1) and
AP
CREWS
A
(C). Tighten
RM
H
when
ARNESSES
A
(B &
OCKER
RMS
S
ONSOLE
UPPORT
IRE
into the
H
(E)
ARNESSES
(7) to the
LAT
A
(7) to the
SSEMBLY
ONSOLE
(17). Align the
RAY
S
ONSOLE
UPPORT
S
(3),
CREWS
S
A
UPPORT
SSEMBLY
P
H
P
AN
EAD
OINTED
(23). Install
AD
3
11
18
C
4P
16P
21
19
2
7
E
1
8
9
A
10
12
1
2PA
2PB
B
4
23
22
3
17
20
F
3
5
Advertisement
