Table of Contents
Advertisement
SECTION 5 ADJUSTMENT PROCEDURES
5-1 PREPARATION
IC-M1V/M1EURO V can be adjusted by sending adjustment data to the RS-232C port via a PC. When you adjust the IC-
M1V/M1EURO V, the optional CS-M1V ADJ
are required.
CABLE
NOTE: *OPC-973 is a modified optional OPC-973
MENT CABLE MODIFICATION).
EQUIPMENT
Output voltage
DC power supply
Current capacity
Measuring range
RF power meter
Frequency range
(terminated type)
Impedance
SWR
Frequency range
Frequency counter
Frequency accuracy : ±1 ppm or better
Sensitivity
Frequency range
Spectrum analyzer
Spectrum bandwidth: ±100 MHz or more
SYSTEM REQUIREMENTS
• IBM PC compatible computer with an RS -232C serial port
(38400 bps or faster).
• Microsoft Windows 95 or Windows 98
• Intel i486DX processor or faster (Pentium 100 MHz or
faster recommended)
• At least 16 MB RAM and 10 MB of hard disk space
• 640×480 pixel display (800×600 pixel display recommend-
ed)
ADJUSTMENT SOFTWARE INSTALLATION
NOTE: Before using the program, make a backup copy of
the original disk. After making a backup copy, keep
the original disk in a safe place.
q Boot up Windows.
- Quit all applications when Windows is running.
w Insert the backup disk1 into the appropriate floppy drive.
e Select 'Run' from the [Start] menu.
r Type the setup program name using the full path name,
then push the [Enter] key. (A:\ setup)
t Follow the prompts.
y Program group 'CS-M1V ADJ' appears in the 'Programs'
folder of the [Start] menu.
CLONING AND ADJUSTMENT CABLE MODIFICATION
a netted line (GND)
(
MICE)
(
+
MIC)
a white color line (MIC)
ADJUSTMENT SOFTWARE
CLONING AND ADJUSTMENT CABLE
GRADE AND RANGE
: 7.4 V DC
: 2 A or more
: 0.1–10 W
: 100–300 MHz
: 50 Ω
: Less than 1.2 : 1
: 0.1–300 MHz
: 100 mV or better
: at least 400 MHz
a red color line (EXT SP)
a black color line (CLONE)
(Rev. 1.0 or later), *OPC-973
(see illustration at CLONING AND ADJUST-
EQUIPMENT
Frequency range
FM deviation meter
Measuring range
Frequency range
Audio generator
Measuring range
Frequency range
Standard signal
Output level
generator (SSG)
Power attenuation
Attenuator
Capacity
STARTING THE PROGRAM
q Connect IC-M1V/M1EURO V and PC with the optional
cables OPC-478, *OPC-973.
w Boot up Windows.
e Click the program group 'CS-M1V ADJ' in the 'Programs'
folder of the [Start] menu, then CS-M1V ADJ's window is
appeared.
r Click 'Connect' on the CS-M1V's window, then appears
IC-M1V's/M1EURO V's up-to-date condition.
t Set or modify adjustment data as desired. See illustration
at ADJUSTMENT SOFTWARE'S SCREEN DISPLAY
EXAMPLE on page 5-2.
IBM is a registered trademark of International Bussiness
Machines Corporation in the U.S.A. and other countries.
Microsoft and Windows are registered trademarks of
Microsoft Corporation in U.S.A. and other countries.
Screen shots produced with permission from Microsoft
Corporation. All other products or brands are registered
trademarks or trademarks of their respective holders.
(
GND)
(
+
CLONE)
INFORMATION: When ordering OPC-973
Part Name:
OPC-973
Order Number:
8900009890
5 - 1
CLONING AND ADJUSTMENT
GRADE AND RANGE
: 30–300 MHz
: 0 to ±10 kHz
: 300–3000 Hz
: 1–500 mV
: 100–300 MHz
: 0.1 µV–32 mV
(–127 to –17 dBm)
: 40 dB or more
: 10 W or more
OPC-478
Advertisement
Table of Contents
