Adjusting The Coffee Mill; Ground Coffee (Instead Of Beans); Delivering Hot Water; Changing The Quantity Of Hot Water - AEG PE4542-M User Manual

ADJUSTING THE COFFEE MILL

The coffee mill is preset in the factory and should not require
adjusting. However, if after making the first few coffees you find
that delivery is either too fast or too slow (a drop at a time), this
can be corrected by adjusting the grinding adjustment knob (fig.
14).
Important! The grinding adjustment knob must only
be turned when the coffee mill is in operation.
For slower delivery and creamier coffee, turn one click anti-
clockwise (finer pre-ground coffee).
For faster delivery (not a drop at a time), turn one click clockwise
(coarser pre-ground coffee).
PREPARING COFFEE WITH PRE-
GROUND COFFEE (INSTEAD OF BE-
ANS)
• Press the icon (B4) (fig. 7) and select the pre-ground
coffee function.
• Extract the machine by pulling it outwards using the han-
dles
• Lift the central lid, place one measure of pre-ground coffee
in the funnel (fig. 19), push the appliance in then proceed
as described in the section "Making coffee using coffee be-
ans". N.B.: You can make just one coffee at a time by pres-
sing the icon (B10) (fig. 12).
• After using the machine with pre-ground coffee, to go back
to making coffee using beans, deactivate the pre-ground
coffee function by pressing the
NOTE 1: Never introduce pre-ground coffee when the machine is
off or it could spread through the inside of the appliance.
NOTE 2: Never add more than 1 measure, otherwise the applian-
ce will not make the coffee.
NOTE 3: Use the measure provided only.
NOTE 4: Introduce only pre-ground coffee for espresso coffee
machines into the funnel.
NOTE 5: If more than one measure of pre-ground coffee is used
and the funnel clogs, push the coffee down with a knife (fig. 21)
then remove and clean the brewing unit and machine as descri-
bed in the "Cleaning the brewing unit" section.

DELIVERING HOT WATER

•
•
•
CHANGING THE QUANTITY OF HOT
WATER
The machine is set by default to automatically delivery 200 ml
of hot water.
To change these quantities, proceed as follows:
•
•
•
•
•
•
•
MAKING CAPPUCCINO (USING THE
icon (B4) (fig. 7).
STEAM FUNCTION)
•
•
12
Always make sure the appliance is ready.
Turn the cappuccino maker outwards and place a container
underneath (fig. 5).
Press the icon (B13) (fig. 20).
Press the OK icon (B9) again and hot water is delivered
from the cappuccino maker into the container underneath.
You should not deliver hot water for more than 2 minutes at
a time.
To interrupt, press the icon (B13) or the ESC icon (B6).
The appliance stops delivery once the set quantity is rea-
ched.
Place a container underneath the cappuccino maker (fig.
3).
Press the icon (B2) to enter the menu (fig. 15) or press
the icons (B7) and (B8) (fig. 2) until "PROGRAM
HOT WATER" is displayed.
Press the OK icon (B9) to confirm.
Select the required quantity of water by pressing the
icons (B7) and (B8). The progress bar shows the
quantity of water selected.
Press the OK icon (B9) to confirm (or the ESC icon (B6) to
cancel the operation.
Press the ESC icon (B6) (fig. 18) twice to exit the menu.
The appliance is now reprogrammed with the new settings
and is ready.
Turn the cappuccino maker towards the centre (fig. 5).
Take a container, fill it with about 100 g of milk for each
cappuccino to be made and place it under the cappuccino
maker. In choosing the size of the recipient, bear in mind
that the milk doubles or triples in volume.
You are recommended to use partially skimmed milk at
EN