Venting Requirements And Options - Direct Vent Only - Vermont Castings OXDV30NV Homeowner's Installation And Operating Manual

Venting Requirements and Options -
Direct Vent ONLY
Approved Vent System components
The heater must be vented to the outdoors through an adjacent
exterior wall or through the roof. The venting system must be
comprised of the appropriate listed venting components speci-
fied on this page. These parts are available from DuraVent Cor-
poration or your Vermont Castings Group Dealer.
Refer to Figure 4 for dimensions relevant to the standard mini-
mum-vent kits.
Simpson DuraVent components
www.duravent.com
Phone: 1-800-835-4429, Fax: 1-707-446-4740
Minimum Horizontal Vent Kit
Starter Pipe Assembly (incl. inner & outer sections)
90° Elbow, Blk.
45° Elbow, Gal.
6" Straight, Blk.
9" Straight, Blk.
11" - 14B\," Adjustable Straight Section
12" Straight
24" Straight
36" Straight
48" Straight
Horizontal Vent Cap
Wall Plate
Vinyl Siding Shield
Snorkel Termination - 14"
Snorkel Termination - 36"
Wall Strap
Cathedral Ceiling Support Box
Storm Collar
Wall Thimble
Firestop Spacer
Flashing 0/12 - 6/12
Flashing 6/12 - 12/12
Steel Chimney Conversion Kit
Kit A (6B\," - 8B\,")
Kit B (6B\," - 10Z\x")
Kit C (6B\," - 13")
Masonry Chimney Kit
Vertical Termination Cap (High Wind)
Vertical Termination Cap (Low Profile)
*Included in Minimum Horizontal Vent Kit #2792
All DuraVent Straight vent pipe sections have a net length 1Z\x" (37mm)
less than the nominal dimension; i.e., a 6" (152mm) Straight pipe sec-
tion has an effective length of 4Z\x" (115mm).
Vermont castings Group Vent components
The following kits are available to meet the needs of most in-
stallations. All pipe has a 7" outer diameter and includes a 4"
diameter inner section. A (CG) designation indicates the part is
finished in Charcoal Gray paint. Consult your dealer about other
vent parts that may be appropriate to complete the installation.
Through the Wall Vent Kit
(1) 90-Degree Elbow (CG)
(1) 24" termination pipe (CG)
(1) 24-44" Adjustable Section
(1) Side Wall Termination, cool touch with siding shield
(1) Firestop
(1) Zero-clearance sleeve
(1) Hardware package
(1) Finishing plate (CG)
(1) Finishing collar (CG)
(4) Charcoal Gray flue pipe rings
30005123
Vertical Termination Kit, 1/12-6/12 pitch
(1) Combination Horizontal Offset / Roof Support
(1) Vertical Termination
(1) Storm Collar
(1) 1/12-6/12 Flashing
(1) Finishing Plate (CG)
(1) Finishing Collar (CG)
(1) Polished Brass Flue Pipe Ring
(1) Hardware Package
Vertical Termination Kit, 7/12-12/12 pitch
(1) 7/12 - 12/12 Flashing
and all of the other Vertical Termination parts.
Vertical Termination, Flat Roof
(1) Flat Flashing
and all of the other Vertical Termination parts.
Twist Lock 24" Straight pipe (cG)
(1) 24" Non-adjustable Pipe
(1) Polished Brass Flue Pipe Ring
2792
Twist Lock 48" Straight pipe (cG)
2768*
(1) 48" Nonadjustable Pipe
46DVA-E90B*
(1) Polished Brass Flue Pipe Ring
46DVA-E45
Twist Lock 45-Degree Elbow (cG)
46DVA-D6B*
for vertical offsets
46DVA-09B
(1) 45-degree Elbow
46DVA-08AB
(1) Polished Brass Flue Pipe Ring
46DVA-12
Draft Hood Adapter
46DVA-24B*
combination Offset/Roof Support
46DVA-36B
Attic Insulation Shield
46DVA-48
7" charcoal Gray pipe Rings, (4)
46DVA-HC*
7" polished Brass pipe Rings (4)
46DVA-DC
Selkirk corporation Vent components
46DVA-VSS
www.selkirkcorp.com
46DVA-SNK-14
46DVA-SNK30
1301 W. President George Bush Highway Ste. 330
46DVA-WS
Richardson, TX 75080
46DVA-CS
Phone: 1-800-992-8368, Fax: 1-877-393-4145
46DVA-SC
Appliance Adapter
46DVA-WT
90° Elbow, Blk.
46DVA-FS
45° Elbow, Blk.
46DVA-F6
6" Straight, Blk.
46DVA-F12
9" Straight, Blk.
4" - 10" Adjustable Straight Section, Blk.
46DVA-KCA
12" Straight, Blk.
46DVA-KCB
18" Straight, Blk.
46DVA-KCC
24" Straight, Blk.
46DVA-KMC
36" Straight, Blk.
46DVA-VCH
48" Straight, Blk.
46DVA-VC
Horizontal Vent Cap
Wall Plate
Vinyl Siding Shield
Snorkel Termination - 14"
Snorkel Termination - 36"
Wall Strap
Cathedral Ceiling Support Box
Storm Collar
Firestop Spacer
Flashing 0/12 - 6/12
Flashing 6/12 - 12/12
Steel Chimney
7TFSSK
Horizontal Kit A
Horizontal Kit B
Vertical Kit
Masonry Chimney Kit
Vertical Termination Cap
NOTE: Direct vent pipe may be used on the Natural Vent system
from the top of the draft hood adapter to the ceiling.
Oxford Direct Vent / Natural Vent Gas Heater
7TDVSKVA
7TDVSKVB
7DVSKVF
7TFSDVp24
7TFSDVp48
7TFSDVT45
FSDHAG
7DVcS
7DVAIS
7FSDRG
7FSDRp
4DT-AAV
4DT-EL90B
4DT-EL45B
4DT-06B
4DT-09B
4DT-AJ12
4DT-12B
4DT-18B
4DT-24B
4DT-36B
4DT-48B
4DT-HC
4DT-WT
4DT-VS
4DT-ST14
4DT-ST36
4DT-WS/B
4DT-CCS
4DT-SC
4DT-FS
4DT-AF6
4DT-AF12
4DT-HKA
4DT-HKB
4DT-VKC
4DT-MCK
4DT-VC
13