Table of Contents
Advertisement
MODELOS RFS-P
R resistencia
Ts termostato de seguridad
C selector tres posiciones
MODELO RFS-F
R resistencia
Ts termostato de seguridad
MODELOS RFS-E
R resistencia
Ts termostato de seguridad
C selector tres posiciones
8
ESQUEMAS ELÉCTRICOS
INSTALLATION INSTRUCTIONS
1.- WARNING
Please read these instructions before installing or using this appliance for the first time.
•
The warranty of the heater will not cover any damage caused by non observance of any of these instructions.
•
This guide must be kept and given to any new owner.
•
Please check that the voltage in the rating label fits the power supply.
•
Any reinstallation should be carried out by trained personnel.
•
The use of these heaters is forbidden in any area where there is a presence of gases, explosives or inflammable objects.
•
DO NOT USE THIS HEATER TO DRY CLOTHES.
•
The surfaces of this heater can be hot, so young children should not be left unsupervised in the vicinity of the heater.
•
Neither the connecting cable nor any other object must come into contact with the hot unit.
•
Do not cover this heater at any time.
•
The air outlet at the top of the thermal radiator and the air inlet at the bottom are provided to ensure the most efficient operation of the appliance. They
also protect the heater from overheating; therefore, it is essential that at no time are they covered.
•
This heater should be switched off at the isolating switch before any repair work is carried out.
•
The thermal radiator should not be installed just below an electrical socket.
•
The appliance must be installed in such a way that it is impossible for anyone using a bath or shower, to touch the controls.
•
The installation must be carried out in accordance with the current electrical regulations.
•
The heater is fitted with a flexible cable size 3 x 1.00 mm2 for electrical connection. It may be used to connect the heater to the fixed wiring of the
premised through a suitable connection box positioned adjacent to the heater.
•
The supply circuit to the heater must incorporate a double pole isolating switch having a contact separation of at least 3 mm.
•
During the first charging cycles radiator can give off some odour, in that case give the room adequate ventilation.
•
If the flexible power cable for this unit is damaged, it may only be replaced by a repair workshop recognised by the manufacturer, as special tools are
necessary.
•
This appliance must be earthed.
•
All models are supplied with an electrical interrupt cut-out. This will switch off the heater if, for any reason, it overheats. Should the cut-out operate, turn
the heater off and remove the cause for the overheating. The cut-out will be reset automatically.
•
The presence of air particles of smoke, dust and other pollutants could, in time, discolour the walls and surfaces around the heater.
MODELS
RFS4P
RFS6P
RFS8P
RFS10P
RFS12P
RFS4F
MODULES
4
6
8
10
12
4
W (cm)
41.5
57.5
73.5
89.5
105.5
41.5
D (cm)
H (cm)
WEIGHT (kg)
9
12
15
18
21
9
VOLTAGE
INPUT (W)
500
750
1000
1250
1500
500
2.- INSTRUCTIONS ON INSTALLATION
- Open the carton at the indicated side. The screws are in the accessories bag. Turn the carton upside down to allow the heater to stand. Check that it is
the correct model and that it is in good condition.
- To obtain optimum performances it is necessary to maintain a minimum clearance of 15 cm between the radiator and any inflammable material as
furniture, curtains etc. See figure.
Closest object
to the left end
minimum15cm
minimum 10cm
RFS6F
RFS8F
RFS10F
RFS12F
RFS4E
RFS6E
RFS8E
6
8
10
12
4
6
8
57.5
73.5
89.5
105.5
41.5
57.5
73.5
10 plus 2 cm separation from the wall
58
12
15
18
21
9
12
15
220-240V~
750
1000
1250
1500
500
750
1000
shelf
minimum 15cm
Closest object
to the right end
minimum 25cm
RFS10E
RFS12E
10
12
89.5
105.5
18
21
1250
1500
9
Advertisement
Table of Contents
