Related Manuals for Pride Mobility Jazzy Elite ES
Summary of Contents for Pride Mobility Jazzy Elite ES
- Page 1 JAZZY Elite ES Series Including Models: Jazzy Elite ES, Jazzy Elite ES Portable, and Jazzy Elite ES-1...
- Page 2 On the product, this icon is represented as a black symbol with a red circle and red slash. NTENDED The intended use of the Pride Mobility Products device is to provide mobility to persons limited to a seated position that have the capability of operating a powered wheelchair. Quick Reference Information...
-
Page 3: Table Of Contents
Table 1. Word Variations Jazzy Elite ES Series www.pridemobility.com... -
Page 4: Introduction
I . I N T R O D U C T I O N SAFETY WELCOME to Pride Mobility Products (Pride). The power chair you have purchased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident that these design features will provide you with the conveniences you expect during your daily activities. - Page 5 Place unit on level ground and stand to one side when changing from drive mode to freewheel mode or freewheel mode to drive mode. Locked and in drive mode. Class II Equipment. Manufactured in Main Frame Power chair information label Jazzy Elite ES Series www.pridemobility.com...
-
Page 6: General Guidelines
Check battery charge. See VI. “Batteries and Charging.” Ensure the manual freewheel levers are in drive mode before sitting on the power chair. NOTE: If you discover a problem, contact your authorized Pride Provider for assistance. www.pridemobility.com Jazzy Elite ES Series... - Page 7 THE JAZZY ELITE ES SERIES POWER CHAIR The Jazzy Elite ES Series Power Chair has two main assemblies: the seat assembly and the power base assembly. See figure 1. Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/brake assemblies, two drive wheels, two rear caster wheels, two front anti-tip wheels, two batteries, and wiring harnesses.
-
Page 8: Electrical Components
ANTI-TIP FRONT COVER WHEELS Figure 2. The Jazzy Elite ES Series Power Base Electrical Components The electrical components are located either on or inside the power base. The main circuit breaker is located on the side of the power base. The power module is located under the front cover. See figures 3 and 4. - Page 9 POWER MODULE QUICK RELEASE BATTERY CONNECTORS (1 OF 2) MOTOR CONNECTORS QUICK RELEASE POWER MODULE CONNECTOR BATTERY TERMINALS (2 OF 4) MAIN CIRCUIT BREAKER Figure 4. Jazzy Elite ES Series Electrical Components (Elite ES Portable Shown) Jazzy Elite ES Series www.pridemobility.com...
- Page 10 WARNING! Do not use the freewheel lever handles as tie-down points to secure this product. FREEWHEEL LEVERS FREEWHEEL LEVERS Figure 5. Drive Mode (Drive Engaged) Figure 6. Freewheel Mode (Drive Disengaged) www.pridemobility.com Jazzy Elite ES Series...
-
Page 11: Initial Assembly
5. Plug the controller harness into the connector on the power base. See figure 2. WIRE TIES Figure 8. Controller Harness Routing Jazzy Elite ES Series www.pridemobility.com... - Page 12 Disassembling the power chair frame (Jazzy Elite ES Portable only) The Jazzy Elite ES Portable disassembles into several components: the seat, the shroud, the batteries, the rear section of the power base, and the front section of the power base. See figure 9.
- Page 13 I V . A S S E M B L Y A N D D I S A S S E M B L Y To assemble the Jazzy Elite ES Portable: 1. Put the rear section of the power base and the front section of the power base together.
-
Page 14: Seat Height Adjustment
Your authorized Pride Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements. Do not change your seating configuration without first contacting Pride Mobility Products or your authorized Pride Provider. -
Page 15: Your Power Chair
Do not demographic majority of users. Your change your seating configuration authorized Pride Provider has evaluated without first contacting Pride Mobility your power chair made Products or your authorized Pride necessary adjustments to suit your specific requirements. -
Page 16: Comfort Adjustments
2. Raise or lower the armrest to the desired height. 3. Tighten the setscrew to secure the armrest. Figure 12. Armrest and Seatback Adjustments NOTE: Ensure all hardware is securely fastened after making any adjustments. www.pridemobility.com Jazzy Elite ES Series... -
Page 17: Controller Position
To adjust the foot platform angle: 1. Flip up the foot platform and locate the adjustment Figure 14. Foot Platform Angle Adjustment screw. 2. Turn the adjustment screw to raise or lower the front of the foot platform. Jazzy Elite ES Series www.pridemobility.com... - Page 18 1. Remove the two adjustment screws from the side of each leg rest extension. 2. Slide the leg rest up or down to the desired length. 3. Reinstall the two adjustment screws. LEG REST EXTENSION ADJUSTMENT SCREWS Figure 16. Elevating Leg Rests www.pridemobility.com Jazzy Elite ES Series...
- Page 19 If you discover a problem, contact your authorized Pride Provider maintenance and repair. Jazzy Elite ES Series www.pridemobility.com...
-
Page 20: Batteries And Charging
Refer to the manual supplied with the battery charger for more information. www.pridemobility.com Jazzy Elite ES Series... - Page 21 Many factors come into play when deciding how often to charge the batteries. You may use your power chair all day on a daily basis or you may not use it for weeks at a time. Jazzy Elite ES Series www.pridemobility.com...
- Page 22 More importantly, it will take a few “charging cycles” (a partial drain — then a full recharge) to establish the critical chemical balance that is essential to the battery’s peak performance and long life. It will be well worth it to take the time to break in your battery properly. www.pridemobility.com Jazzy Elite ES Series...
- Page 23 What about shipping? If you wish to use a freight company to ship your power chair to your final destination, repack your power chair in the original shipping container and ship the batteries in separate boxes. Jazzy Elite ES Series www.pridemobility.com...
-
Page 24: Care And Maintenance
V I I . C A R E A N D M A I N T E N A N C E CARE AND MAINTENANCE The Jazzy Elite ES Series are sophisticated power chairs. Like any motorized vehicle, it requires routine mainte- nance checks. You can perform some of these checks, but others require assistance from an authorized service representative. - Page 25 Check the entire power chair for loose hardware and changes in the function or performance of the power chair. See your authorized Pride Provider for service or repair. Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc. Jazzy Elite ES Series www.pridemobility.com...
-
Page 26: Cleaning And Disinfection
WARNING! When changing a tire, remove only the center lug nut and washer, then remove the wheel. If any further disassembly is required, deflate the tire completely or it may explode. www.pridemobility.com Jazzy Elite ES Series... -
Page 27: Battery Replacement
Figure 19. Jazzy Elite ES Series Drive Wheel injury and/or product damage may result. Removal 8. Reinstall the drive wheel nut and washer onto the axle and tighten. See figure 19. NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be replaced with a new nut. - Page 28 Connect Red wire to Red Positive (+) Terminal Post. Connect Black wire to Black Negative (-) Terminal Post. BATTERY STRAPS Figure 20. Battery Installation for Jazzy Elite ES and Jazzy Elite ES-1 (Seat Removed for Clarity) www.pridemobility.com Jazzy Elite ES Series...
- Page 29 - = Negative (Black) Terminal Post Connect Red wire to Red Positive (+) Terminal Post. Connect Black wire to Black Negative (-) Terminal Post. BATTERY STRAPS Figure 21. Battery Installation for Jazzy Elite ES Portable (Seat Removed for Clarity) Jazzy Elite ES Series www.pridemobility.com...
- Page 30 Disconnect both batteries before load testing and follow the directions that come with the load tester. If either one of the batteries fails the load test, replace both of them. If your power chair still does not power up, contact your authorized Pride Provider. www.pridemobility.com Jazzy Elite ES Series...
- Page 32 Jazzy Elite ES Series *INFMANU4355* Product Serial # Jazzy Elite ES Series www.pridemobility.com...
Need help?
Do you have a question about the Jazzy Elite ES and is the answer not in the manual?
Questions and answers
How do I get the batteries out of the Jazzy ES Elite? I fined to remove the seat, please tell me how.
To remove the batteries from the Pride Mobility Jazzy Elite ES:
1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Remove the seat.
4. Remove the main shroud by lifting the rear of the shroud until it disconnects, then slide it forward and lift it over the seat post.
5. Unfasten the battery strap.
6. Disconnect the battery connectors.
7. Remove the batteries from the power base.
This answer is automatically generated
@Mr. Anderson, thank you for answering but the part I need help with is, how do I remove the seat?
the lights at controller don't light up and unit does not turn on. batteries are charged, is this a breaker problem and how do you reset the breaker?
To reset the breaker on a Pride Mobility Elite ES:
1. Locate the main circuit breaker.
2. Allow the power chair to rest for about one minute.
3. Push in the circuit breaker button.
4. Turn on the controller and check if the unit powers up.
If the breaker continues to trip or the unit still does not turn on, check harness and battery connections. If the issue persists, contact an authorized Pride Provider.
This answer is automatically generated
How do I remove the seat to replace the batteries on a Jazzy ES Elite scooter?
To remove the seat to replace the batteries on a Pride Mobility Jazzy Elite ES:
1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Remove the seat.
These are the initial steps before accessing the batteries. After removing the seat, you can proceed to remove the main shroud and battery strap.
This answer is automatically generated
Put the chair in gear and the lights won't quit blinking
The lights on the Pride Mobility Jazzy Elite ES may be blinking when the chair is put in gear due to an issue with the battery condition or electrical connections. Possible causes include loose harness connections, a tripped circuit breaker, or weak batteries. Checking and securing the connections, resetting the circuit breaker, and load testing the batteries can help diagnose the issue. If the problem persists, contacting an authorized Pride Provider is recommended.
This answer is automatically generated
Are there instructions to remove/replace the Pride Mobility Jazzy Elite ES joystick assembly?