Table of Contents
Advertisement
Table of Contents
About This User's Guide ............................................................................... 2
Introduction.................................................................................................... 2
Security System Basics .................................................................................. 3
What is a Point?......................................................................................... 3
What is a "Faulted" Point? ........................................................................ 3
Are All Points the Same? .......................................................................... 3
Controlled Points ........................................................................................... 4
24-Hour Points............................................................................................... 5
Fire Points ................................................................................................. 5
Non-fire 24-Hour Points............................................................................ 5
Keypad Keys.................................................................................................. 5
Keypad Tones ................................................................................................ 6
System Events................................................................................................ 7
Fire Alarms................................................................................................ 7
Burglary Alarms ........................................................................................ 7
Fire Trouble Events ................................................................................... 7
Non-Fire Trouble Events........................................................................... 7
How Your System Reports Alarms ........................................................... 8
Keypad Backlighting ..................................................................................... 8
Checking System Status................................................................................. 8
Silencing Alarms............................................................................................ 9
Turning the System Off ............................................................................... 10
Turning the System All On .......................................................................... 11
Turning the System All On, with No Delay................................................. 12
Turning On Part of the System (Part On)..................................................... 13
Turning the System Part On, with No Delay ............................................... 14
Turning System On, With Points Open (Bypass Points) ............................. 15
Viewing Faulted Points................................................................................ 17
Viewing Alarm Memory.............................................................................. 18
Resetting the System.................................................................................... 19
Selecting Watch Tone .................................................................................. 20
Selecting Watch Points ................................................................................ 21
Checking System Troubles .......................................................................... 22
Changing Passcodes..................................................................................... 23
Step Outside................................................................................................. 24
Exit Only...................................................................................................... 25
Show Passcode Types .................................................................................. 26
Change Passcode Type ................................................................................ 27
Change Other Users' Passcodes................................................................... 29
Renew One-Time Passcodes........................................................................ 31
System Test.................................................................................................. 32
Security System Limitations ........................................................................ 34
Fire Safety and Evacuation .......................................................................... 35
Security System Glossary ............................................................................ 42
Maintenance and Service ............................................................................. 44
Power Failure............................................................................................... 44
How to Clean the Keypad ............................................................................ 44
1
Advertisement
Table of Contents
Related Manuals for Bosch 2212
Summary of Contents for Bosch 2212
-
Page 1: Table Of Contents
Table of Contents About This User’s Guide ................2 Introduction....................2 Security System Basics .................. 3 What is a Point?..................3 What is a “Faulted” Point? ................ 3 Are All Points the Same? ................3 Controlled Points ................... 4 24-Hour Points....................5 Fire Points .................... -
Page 2: About This User's Guide
About This User’s Guide This User’s Guide shows you how to use and maintain your security system. It covers basic functions, such as turning the system on and off. The functions described in this guide are programmed by your security company. -
Page 3: Security System Basics
Security System Basics What is a Point? A “point” is a detection device, or group of devices connected to your security system. Points are identified by the area they monitor, such as front door, bedroom window, or hallway. View the current status of each point in your system through the keypad’s display. -
Page 4: Controlled Points
Controlled Points Controlled points respond to alarm conditions depending upon whether the system is turned on or turned off. They are programmed to either respond instantly to alarm conditions or to provide a delay for you to reach the keypad and turn the system off. Various controlled points may be located throughout your house. -
Page 5: 24-Hour Points
24-Hour Points 24-hour points are always on, even when the system is turned off. There are two types of 24-hour points, fire points and Non-fire points. Fire Points Fire points only monitor fire detection devices, such as smoke detectors. They are always on and cannot be turned off. Non-fire 24-Hour Points Non-fire 24-hour points are always on and cannot be turned off. -
Page 6: Keypad Tones
Keypad Tones Your keypad emits several distinct tones and displays text to alert you to system events. Additional bells or sirens may also be connected to your system. Bells or sirens mounted on the exterior of your premises alert neighbors to emergencies and provide an audible guide for police and fire fighters. -
Page 7: System Events
System Events Your system responds to four types of events. If more than one event occurs, your system sorts them into one of four groups. The groups (highest priority first) are: Fire Alarms, Burglary Alarms, Fire Troubles, and Non-fire Troubles. Fire Alarms Fire alarms are the highest priority events. -
Page 8: How Your System Reports Alarms
How Your System Reports Alarms Your security system may be programmed to automatically disconnect your telephones when sending reports to your security company. Once the report is completed, the system returns the telephones to normal operation (check with your security company). Your system makes repeated attempts to send reports to your security company. -
Page 9: Silencing Alarms
Silencing Alarms When there is an alarm, the alarm tone sounds and the point or points in alarm are shown in the display. If you enter your passcode before the system dials your security company, the alarm is canceled. The point in alarm is shown on the display: ALARM PT 8 MOTION DETECTOR ENTER CODE TO... -
Page 10: Turning The System Off
Turning the System Off You turn off your security system by entering your personal passcode. When the system is on, you must enter through a designated entry door to prevent an instant alarm condition. Opening a designated door starts entry delay time and the keypad emits a pulsing beep tone to remind you to turn the system off. -
Page 11: Turning The System All On
Turning the System All On Use this function to turn on the entire system. Once you’ve pressed [9], exit delay time starts to count down. The length of exit delay time is programmed by your security company. Check with them to learn how much exit delay time your system allows. -
Page 12: Turning The System All On, With No Delay
Turning the System All On, with No Delay I have this feature. I do not have this feature. Use this function to turn on the entire system, both All and Part without entry or exit delays. Remember that turning the system on with no delay allows no exit or entry delay time through the designated delay door. -
Page 13: Turning On Part Of The System (Part On)
Turning On Part of the System (Part On) I have this feature. I do not have this feature. Part On turns on only a part of your system, leaving the rest of the system turned off. Refer to the Point Identification section of your keypad’s reference card to identify Part points. -
Page 14: Turning The System Part On, With No Delay
Turning the System Part On, with No Delay I have this feature. I do not have this feature. Use this function to turn on Part of the system without entry or exit delays. Remember that turning the system on with no delay allows no exit or entry delay time through the designated delay door. -
Page 15: Turning System On, With Points Open (Bypass Points)
Turning System On, With Points Open (Bypass Points) I have this feature. I do not have this feature. The Bypass Points feature is used to exclude points you do not wish to turn on with the rest of the system. If you try to turn your system on and there is a faulted point (door or window open), you can either close it or bypass it. - Page 16 If there are other faulted points, they are displayed in turn. If there are no more faulted points, exit delay begins. The display indicates that the system is being turned on with a bypassed point: 30 SEC TO EXIT! 1 PTS BYPASSED If you bypass a point in error, press [CLEAR] and start over at step 1.
-
Page 17: Viewing Faulted Points
Viewing Faulted Points To properly turn your system on, all doors and windows must be in the normal (not faulted) condition. Use this feature to locate faulted points. Ensure that the system is turned off (On light is off). Press [CLEAR]. If points are faulted, the display shows: NOT READY TO TURN ON HOLD... -
Page 18: Viewing Alarm Memory
Viewing Alarm Memory After an alarm has been silenced and cleared from the display, you may still review the points that were in alarm. Ensure that the system is turned off (On light is off). Press [4]. The following display shows that there are alarms in memory: ALARM MEMORY HOLD 6 TO VIEW... -
Page 19: Resetting The System
Resetting the System Use this feature to reset the system (including fire points) after an alarm. Detection devices, such as smoke detectors and shock sensors, must be reset after being activated. Resetting the system takes about 20 seconds. If points do not reset, contact your alarm company for help. Ensure that your system is off (On light is off). -
Page 20: Selecting Watch Tone
Selecting Watch Tone Your system gives you the ability to watch points when it’s turned off, meaning that it can be programmed to alert you to opened doors and windows. For example, parents with small children may want a tone to be sounded whenever a door or window is opened as a way of monitoring their whereabouts. -
Page 21: Selecting Watch Points
Selecting Watch Points Once you’ve decided how your system will respond to watched points (see Selecting Watch Tone), you need to decide which of the points in your system are to be watched. Use this feature to tell your system which points to watch. -
Page 22: Checking System Troubles
Checking System Troubles Your system emits a trouble tone and displays the SYSTEM TROUBLE message to alert you to system trouble events, caused by such things as low batteries. Use this feature to learn what is causing the trouble and the steps to take to correct it. -
Page 23: Changing Passcodes
Changing Passcodes I have this feature. I do not have this feature. This feature lets you change your personal passcode at any time, without assistance from your alarm company. It is recommended that you write down your old and new passcodes before you begin. Make sure that your system is off (On light is off). -
Page 24: Step Outside
Step Outside I have this feature. I do not have this feature. Use the Step Outside feature to temporarily turn off protection to an entrance door (or doors) when your system is All or Part On with No Delay. You can exit and reenter without turning your system off. Use this feature to pick up the newspaper or to take the dog out. -
Page 25: Exit Only
Exit Only I have this feature. I do not have this feature. The Exit Only feature allows you to exit the premises when the system is All or Part On with No Delay. After exit delay expires, the door is returned to the system so that opening the door causes an alarm. -
Page 26: Show Passcode Types
Show Passcode Types I have this feature. I do not have this feature. Use this feature to find out which passcode type is currently assigned to each of the users of your system. See Change Passcode Types, for a description of passcode types. Make sure the system is turned off (On light is off). -
Page 27: Change Passcode Type
Change Passcode Type I have this feature. I do not have this feature. This feature allows those with Owner Type passcodes to change the passcode type for each of the users in the system. You cannot change your own passcode type. Passcodes can be one of three types: owner, user, or one-time. - Page 28 The following displays identify the current passcode type assigned to user 3 and then instruct you on how to change the passcode type for this user. CODE 3 IS NOW OWNER TYPE PRESS 1 FOR OWNER TYPE PRESS 2 FOR USER TYPE PRESS 3 FOR ONE-TIME...
-
Page 29: Change Other Users' Passcodes
Change Other Users’ Passcodes I have this feature. I do not have this feature. This feature allows those with Owner type passcodes to change the passcodes of system users. Make sure the system is turned off (On light is off). Press [6] and enter your passcode (Owner type required). - Page 30 If the change was successful, the following display is shown. If the error tone sounds, return to step 3. Be sure to enter the same passcode in steps 5 and 6: CODE CHANGED After changing a passcode you should check to see which type it You may continue to change passcodes by following the displayed instructions, or press [CLEAR] to exit.
-
Page 31: Renew One-Time Passcodes
Renew One-Time Passcodes I have this feature. I do not have this feature. One-Time passcodes may be used only once to turn the system off. This feature allows those with Owner Type passcodes to renew One-Time passcodes that have been used. Once renewed, the One-Time passcode again turns the system off one time. -
Page 32: System Test
System Test I have this feature. I do not have this feature. This feature helps to ensure that your system is operating properly by testing the system’s bell, battery, and phone line. If any of these components fails the test, contact your security company for assistance. Be sure to contact your security company before you begin. - Page 33 Finally, the phone connection is tested. This test could take up to ten minutes: TESTING PHONE MAY TAKE 10 MIN. If the phone line passes the test, the display shows: PHONE TEST PASSED If the phone test fails, the display shows: PHONE TEST FAILED When the test is concluded, the system returns to the off state.
-
Page 34: Security System Limitations
Security System Limitations Not even the most advanced security system can guarantee protection against burglary, fire, or environmental threats. All security systems are subject to possible compromise or failure-to-warn for a variety of reasons including, but not limited to, the following: •... -
Page 35: Fire Safety And Evacuation
Fire Safety and Evacuation Residential fire is a leading cause of accidental death. Most fire related deaths occur at night when occupants suffocate in their sleep from smoke and toxic gases, rather than from burns. To help reduce this risk, the following program should be implemented. -
Page 36: System Displays
System Displays Your security system communicates its status and provides instruction to you through keypad displays. The following list presents all possible displays along with an explanation for each. Your system might not use all of them. ALARM PT ## Indicates a point in alarm, the second line shows the point’s name. - Page 37 Indicates the passcode is an Owner CODE # OWNER type. Indicates the passcode is a User type. CODE # USER Indicates the passcode has been CODE CHANGED changed. Indicates the attempt to change the CODE NOT CHANGED passcode was unsuccessful. This display is shown when a ENTER CODE passcode is being entered.
- Page 38 HOLD TO VIEW Indicates a point is faulted. Hold ] to see which point it is. FAULTED POINTS (IDLE TEXT LINE 1) This display is shown when the system is turned off. (IDLE TEXT LINE 2) LOW BATTRY PT ## Indicates a point has a low battery.
- Page 39 POINT ## FAULTED Indicates the named point is faulted. [point text] Indicates the system has faulted POINTS FAULTED points. Prompt to press [ ] to bypass a POINTS FAULTED point that became faulted during exit press delay. Prompt to press [1] to assign an PRESS 1 FOR Owner type passcode to a given user.
- Page 40 PT ## BYPASSED Indicates the point shown was bypassed. [point text] PT ## FAULTED Indicates point shown is faulted. [point text] PT ## WATCH OFF Indicates the point is not being watched. [point text] PT ## WATCH ON Indicates point is being watched. [point text] PUSH [CLEAR] Prompt to press [CLEAR] to return...
- Page 41 Indicates there is a system trouble SYSTEM TROUBLE condition. TAMPER PT ## Indicates a point was tampered with. [point text] TESTING BATTERY Indicates the battery test is in progress. MAY TAKE 4 MIN. Indicates the bell test is in progress. TESTING BELL TESTING PHONE Indicates the phone test is in process.
-
Page 42: Security System Glossary
Security System Glossary All On Turns on all of the points in the system. Burglary Alarm Tone Constant warble tone. Bypass Selectively removes points from the security system temporarily. Central Station Facility where trained personnel monitor your security system 24 hours a day. - Page 43 Point (PT) Detection device, or group of devices connected to your security system. Points display individually at the keypad on lights one to eight. Press/Push Used interchangeably to instruct you to momentarily push down and then release a key. Trouble Service condition that needs to be corrected, such as a broken wire.
-
Page 44: Maintenance And Service
Maintenance and Service This security system requires very little maintenance; however, you should test the system weekly to ensure it is working properly. A test schedule and maintenance program can be arranged. If you notice a change in operation during normal use or testing, call for service as soon as possible.