Weller WD1 Operating Instructions Manual page 9

6 6 . . 1 1 . . 7 7 L L o o c c k k F F u u n n c c t t i i o o n n " "
The Lock Function locks the soldering station control so
that no setting changes are possible. Radio Buttons I I , , I I I I , ,
a a n n d d I I I I I I remain operational in the lock mode. When the
lock function is selected in the Special Functions menu,
"O O F F F F " and the flashing "
menu display. If Radio Buttons I I or I I I I are depressed
while "O O F F F F " appears in the display, no code is saved.
The U U P P or D D O O W W N N Scroll Keys can be used to enter a 1, 2
or 3-digit Lock code. Confirm the code by depressing
Radio Button I I I I I I for 5 seconds. The station is now
Locked and the " " symbol appears in the main dis-
play.
To unlock, activate the Lock Function in Special
Functions menu 1. "O O N N " appears in the display. Enter
the code and confirm by depressing Radio Button I I I I I I .
The station is now unlocked.
Switch to previous menu item with Radio Button I I .
Switch to next menu item with Radio Button I I I I .
6 6 . . 2 2 S S p p e e c c i i a a l l F F u u n n c c t t i i o o n n s s M M e e n n u u 2 2
If the U U P P and D D O O W W N N Scroll Keys are pressed simultane-
ously, after approximately 4 seconds, the menu selection
for the Special Functions is activated and - - 2 2 - - appears
in the display. Release the Scroll Keys.
Radio Buttons I I and I I I I are used for menu selection.
M M e e n n u u s s e e l l e e c c t t i i o o n n
" "
" symbol appears in the
M M e e n n u u 2 2
E E x x i i t t
I I
F F a a c c t t o o r r y y
C C o o n n t t r r o o l l
C C h h e e c c k k
R R E E M M O O T T E E I I D D
6 6 . . 2 2 . . 1 1 F F actory C C o o n n t t r r o o l l C C heck F F u u n n c c t t i i o o n n ( ( F F C C C C ) )
This function checks temperature accuracy of the sol-
dering station and allows modifications if necessary. To
peform the "FCC" function, the soldering tip tempera-
ture must be measured using an external temperature
measuring instrument.
F F C C C C 2 2 1 1 2 2 ° ° F F / / 1 1 0 0 0 0 ° ° C C
+ 1
- 1
I I I I
Confirmation
5 sec.
Select the "FCC" High or Low Set point with the U U P P or
D D O O W W N N Scroll Key. After the "FCC" function is complete
at both "Set" points, Radio Button I I I I I I is used to exit the
menu.
U U P P Scroll Key: High "Set" point 842°F/450°C
D D O O W W N N Scroll Key: Low "Set" point 212°F/100°C
R R e e s s e e t t t t i i n n g g t t h h e e S S p p e e c c i i a a l l F F u u n n c c t t i i o o n n s s t t o o F F a a c c t t o o r r y y S S e e t t t t i i n n g g s s
Press and hold the I I I I I I Radio Button. Then press the U U P P
and D D O O W W N N Scroll Keys at the same time. "F F S S E E ",
"Factory Setting Enabled" appears in the display. The
station is now reset to its factory default settings.
I I I I
I I I I
EXIT
EXIT
E E n n g g l l i i s s h h
I I I I I I E E X X I I T T
F F C C C C 8 8 4 4 2 2 ° ° F F / / 4 4 5 5 0 0 ° ° C C
+ 1
- 1
Confirmation
842°F(450°C)
212°F (100°C)
7 7