Page 1
Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at Custom Front Models vikingrange.com All Refrigerator/Freezer/ Side-by-Side/Bottom-Mount (022309J) F20634 EN...
Table of Contents IMPORTANT – Please Read and Follow Warnings & Important Information ____________________________________________________________________3 • Make sure that incoming voltage is the same as Your safety and the safety of others is Bottom-Mount unit rating. An electric rating plate specifying Dimensions and Specifications (36”) __________________________________________________________4 very important.
Overlay Dimensions Custom Grille Dimensions (Bottom-Mount) (Bottom-Mount) 36” Custom Panels 36” Custom Grille 1 / 2 ( 1 . 2 ” 3 / 4 ” ( 1 . 9 ” 2 - 3 d i u d i u d i u ( 6 .
Dimensions Specifications (Side-By-Side) (Side-By-Side) 48” Side-By-Side 42” Side-By-Side Description DFSB542 DFSB542D Overall width 42” (106.7 cm) Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16” (60.5 cm) To front of top grille: 24-3/4”...
Overlay Dimensions Custom Grille Dimensions (All Refrigerator/Freezer) (All Refrigerator/Freezer) 30” Custom Panels 30” Custom Grille 1 / 2 ( 1 . 2 ” 3 / 4 ” ( 1 . 9 ” 2 - 3 d i u d i u d i u 36”...
Cabinet Information Cabinet Information Full overlay models, (with 3/4” [1.9 cm], thick panels and custom handles locally supplied), Full overlay models can be installed in standard 24” (61.0 cm) deep openings. However, fit flush in 25” (63.5 cm) deep (countertop depth) cabinet openings with no protrusion into the door faces and top ventilation grille will protrude 3/4”...
Custom Side Panel Dimensions Custom Panel General Information Custom finishing options • Panel thickness must not exceed 1” (2.5 cm) • All installations must allow for the refrigerator on hinge side. Thicker panels will interfere with 1” and freezer door to open a minimum of 90˚. door swing and clearance.
Ice and Water Dispenser Bezel Removal Custom Door Panel Installation (if required cont.) (Refrigerator or Freezer) Remove handle side cabinet screws Remove 2 additional screws under Remove mounting support. Remove all screws from handle side door trim. top section of bezel. and trim with a phillips screwdriver.
Custom Door Panel Installation Custom Freezer Door Panel Installation (Refrigerator or Freezer cont.) (Bottom-Mount Only cont.) Reinstall handle side door trim Open freezer door. Remove door trim screws Remove FOL bracket. Slide custom wood panel to the hinge side, ensuring “Z”...
Ice and Water Dispenser Bezel Installation Ice and Water Dispenser Bezel Installation (if required) (if required cont.) Install custom wood panels per product’s Locate opening in door and position bezel. Adjust and reposition bezel Replace spill tray in lower part of bezel. installation instructions.
Custom Grille Installation Bottom-Mount Custom Panel Hinge Cutout (if required) (cont.) 5 / 8 ” ( 1 . 6 3 ” ( 7 . 6 Install two screws but DO NOT tighten all the way. Measure and cut 2-1/16” diagonal in Pull air grille assembly forward.
DO NOT Use only 1/4” (6 mm) copper tubing for water • The installation of Viking units with a reverse have a fuse in the neutral or grounding circuit. line. DO NOT install copper tubing in area osmosis system is acceptable as long as the •...
Installation General Information Professional • Most of the unit’s weight is at the top. Extra Tip Over Hazard care is needed when moving the unit to Appliance is top heavy and tips easily when not prevent tipping. completely installed. Keep doors closed until appliance is completely installed and secured per •...
Hinge Adjustment Installation (cont.) Front of unit Carefully move unit until semi flush with cabinet Remove four side screws and remove unit top. Loosen the four hinge screws. Adjust door. Place unit within 3” of being flush with cabinets. (depending on unit). Retighten four hinge screws.
Hinge Adjustment Door Stop Adjustment (cont.) (Side-by-Side) 120˚ Screw 110˚ Wall 90˚ 2 x 4 Refrigerator Attach positive secure self-tapping bolts Open refrigerator door so door stop and Remove shoulder screw and place in 90˚ Lift unit off rollers to desired height to 2 x 4 using a 22”...
Water Filter System Specification and Water Filter Installation (Side-by-Side with Dispenser) Performance Data Sheet This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration of less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53.* (100% safety factors built-in for unmetered usage for health claims only.) Standard No.
Final Installation Performance Checklist Replace top air grille. Using an 8” magnetic nut driver, replace the two 1/4” screws. Professional Designer Replace the center grille louver. Replace the center grille louver. h Align/square door(s). h Verify cabinet size. h Verify electrical supply and water supply h Verify drain pan is properly installed and (if applicable).
Verify Operations Verify Operations Control Panels Control Panels Bottom-Mount All Refrigerator Side-by-Side All Freezer 1. Press “Activate Controls” pad 1. Press “Activate Controls” pad 2. Verify unit is not in Sabbath Mode 2. Verify unit is not in Sabbath Mode If in Sabbath Mode: If in Sabbath Mode: A.
Service & Registration Notes ________________________________________________________________________________________________________________________________________________________ Only authorized replacement parts may be used in performing service on the appliance. DO NOT repair or replace any part of the appliance unless ________________________________________________________________________________________________________________________________________________________ specifically recommended in the manual. All other servicing should be referred to a qualified ________________________________________________________________________________________________________________________________________________________ technician.