Lp Container; Servicing And Filling Lp Containers; Installing Lp Containers - Jayco Eagle Owner's Manual

LP Container

The tank or bottle is a D.O.T. approved container to hold fuel in liquid form, and is
normally a 20# or 30# capacity. The open/close valve is to be closed at all times unless
hooked up to LP gas system or filling container. When container is disconnected from
hose and P.O.L. connection, install P.O.L. plastic plug as attached to container. This is
required by RV industry, Gas Association, and for your own safety. Do not allow
container (filled or empty) to move or roll around while transporting to and from filling
location.
WARNING: Because your vehicle has exterior combustion air inlets, all
appliance pilot lights should be turned off during gasoline or propane refuel-
ing. Laws in some states require this.

Servicing and Filling LP Containers

Filling an LP container correctly is very important and should be performed by a
qualified person who knows the proper safety procedures and inspecting containers. Any
new container must be carefully purged for best performance and must NEVER BE
OVERFILLED.
Caution: DO NOT use tools to open or close tank valve. HAND TIGHTEN ONLY.
LP gas expands 1½% for each 10° increase in temperature. It is imperative to leave
sufficient space inside the container to allow for the natural expansion of gas during
warmer weather. Each propane container is equipped with an overfill device built into the
main valve. This device must remain open during the filling. When the container is filled
to 80%, the maximum level for safety, a liquid will appear replacing the vapor. Stop
filling immediately and close both valves; HAND TIGHTEN ONLY.
WARNING: A propane container should never be filled beyond 80% of its
capacity.
If your tank becomes overfilled and is not allowed to "bleed off" before installation to the
RV system, it may gain pressure from exposure to direct sunlight and will begin "blowing
off" pressure from the overflow valve. This will be detected by the strong odor around
the tanks. Keep open flames away from this area. It is best to find a technician qualified
in releasing an overfill from the container. If that is not possible, remove the bottle, take
it to a safe area at least twenty-five feet from any source of combustion, and "bleed off"
the excess pressure by opening the valve slightly and closing it when discharge has been
sufficient, one to two minutes.
WARNING: LP gas containers are equipped with safety devices, which relieve
excess pressure by discharging gas into the atmosphere. Do not bring or store LP
gas containers, gasoline or other flammable liquids inside the recreational ve-
hicle. Disregarding this warning may result in fires or explosions.
44
When an LP container gets low, sometimes there is a concentration of garlic-like odor
which may be mistaken for a gas leak. After a change over to a full tank, the odor usually
will disappear. If not, turn off the LP container(s) and have the system checked by a
qualified technician.
1. Knob to open valve to fill or to use camper.
2. Complete valve assembly.
3. "10%" valve, small brass knob or slot screw.
4. Container mounting stand.
A warning label has been located near the LP gas container. This label reads:
THIS GAS PIPING SYSTEM IS DESIGNED FOR USE OF
LIQUEFIED PETROLEUM GAS ONLY. DO NOT CONNECT
NATURAL GAS TO THIS SYSTEM. DO NOT FILL
CONTAINER(S) TO MORE THAN 80 PERCENT OF CAPACITY.
Securely cap inlet(s) when not connected for use. After turning
on gas, except after normal container replacement, test gas
piping and connections to appliances for leakage with soapy
water or bubble solution. Do not use products that contain
ammonia or chlorine.

Installing LP Containers

1. Place container onto steel angle rack.
2. Insert 2- / " x / " bolts through hole in
1 1
4 2
center of angle.
3. Attach lock washer and nut onto bolt.
CAUTION: Ensure that all fasteners are secured before traveling.
AD-34
45