1. Manuals
  2. Brands
  3. i3TOUCH Manuals
  4. Monitor
  5. Excellence
  6. User manual

i3TOUCH Excellence User Manual

Hide thumbs Also See for Excellence:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Installation Manual
i3TOUCH Excellence
Monitor User Guide
Version 3.6.2

Advertisement

Table of Contents
loading

Related Manuals for i3TOUCH Excellence

Summary of Contents for i3TOUCH Excellence

  • Page 1 Excellence Monitor User Guide Version 3.6.2...
  • Page 2 1. Introduction 2. Connecting the Monitor 3. Using the Monitor 4. Cleaning the screen of LCD Monitor 5. Disclaimer 6. Trouble Shooting 7. Supplement i3TOUCH EXCELLENCE Monitor User Guide Version 3.6.1...

  • Page 3: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 1. Please read this instructions carefully before using the product and keep it for later reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Clean the product with a damp soft cloth. Do not use liquid or aerosol cleaners as it may cause permanent damage to the screen.

  • Page 4: General Function

    2. Do not use corrosive or abrasive detergents, waxes or solvents for cleaning. Use only a dry or damp with clean water, soft cloth when cleaning. 3. Use qualified and safety-approved AC power cord only. i3TOUCH EXCELLENCE Monitor User Guide Version 3.6.1...
  • Page 5 1-3 Check List When opening the carton, please make sure that all the items listed below are present: 1. VGA cable (male-to-male) ×1 2. Power cord ×1 3. USB cable ×1 (for touch monitor models only) 4. HDMI cable x1 5.

  • Page 6: Connecting The Monitor

    Please connect the signal source first, then follow by connecting USB cable for touch. For Operating Systems other than Windows 7 or Windows 8, drivers are required. Please download the latest drivers at www.i3-learning.com i3TOUCH EXCELLENCE Monitor User Guide Version 3.6.1...

  • Page 7: Using The Monitor

    3. Using the Monitor 3-1 Get to know the monitor The Monitor connectors are located on the rear side. They are shown in the physical monitor as figure below and described in the following paragraphs. Please note that connectors may vary in some derivative models; please refer to individual leaf- let for special notation.
  • Page 8 Operation distance: > 10 meter (32ft.) Working angle: not more then +/- 40 degree CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYP DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION i3TOUCH EXCELLENCE Monitor User Guide Version 3.6.1...
  • Page 9 3-4 Understanding the OSD Menu (with Remote control) a. Power Press the power button to turn on/off the monitor and IPC (If IPC is build-in with monitor). b. HDMI 1 Press this button to select the HDMI 1signal source. c. HDMI 2 Press this button to select the HDMI 2signal source.
  • Page 10 Press Exit button to exit setting, or, exit OSD menu. Alternatively, press “Menu” button to exit the OSD Menu instantly at any time. r. Info Press to show timing and resolution s. USB Function Press to control USB function. i3TOUCH EXCELLENCE Monitor User Guide Version 3.6.1...
  • Page 11 3-4 Content of OSD Menu Picture // press (UP/Down) to select sub menu, press to next page(Sound/ Option) • Picture mode Contrast Brightness Color Sharpness Tint • Color Temperature Standard Cool Medium Warm • Aspect Ratio • Noise reduction • PC Setup Auto Adjust •...
  • Page 12 Female DB9 DCE pin numbering and definitions: recommended communication rates are: (higher baud rates are fine but 9600 is by far the most common and is sufficient for the volume of data being transmitted) i3TOUCH EXCELLENCE Monitor User Guide Version 3.6.1...

  • Page 13: Data Structure

    3-6-3 Data structure Note: All numbers shown are in the protocol description are in string unless indicated otherwise. Percentages are shown in decimal. General Command Form • STX. The first character is the standard Start of Text (STX) character ‘S’. •...

  • Page 14: Command Code

    For the properties that support ranges such as brightness and volume, examples are provided for low, and high. Any intervening values can be deduced from these. This section only covers the commands sent from the computer to the device. For responses from the device, see sections 3-6-4-2 – ACKs/ Notifications. i3TOUCH EXCELLENCE Monitor User Guide Version 3.6.1...
  • Page 16 Note: do reset this value will be set as default 15. it works on power on status. Note: the system doesn’t allow to “Ping/ Query/ Bulk Query” more than one device at one time. Note: if your system need “Query” function, please contact engineer. It’s a standard function. i3TOUCH EXCELLENCE Monitor User Guide Version 3.6.1...
  • Page 17 4. Cleaning the Monitor 1. Make sure the monitor is turned off. 2. Never spray or pour any liquid directly onto the screen or case (depends on different model). 3. Do not use chemical solvents, alcohol, or any other based to clean the unit or panel. It may cause permanent damage on the unit or panel.
  • Page 18 Timing modes exceeding above chart may show abnormal, off-center, unproportionate, picture on the screen, or even “No Signal” as such timing mode maybe completely undisplayable, please refer to graphic card output timing mode respectively. i3TOUCH EXCELLENCE Monitor User Guide Version 3.6.1...
  • Page 20 AUTHORISED DISTRIBUTOR WWW.I3-TECHNOLOGIES.COM INFO@I3-TECHNOLOGIES.COM...

Table of Contents