Advertisement
1.
Overview
The new Chroma-Q® Color One 100 is a LED Par fixture with 24 high powered RGBA LEDs and a fully homogenised
beam. Built with an internal power supply, the fixture operates as a standalone unit with the wireless IR Remote or
controlled via an external DMX console.
The Color One 100 is available in 2 models. The IP20 version is fitted with chassis mount powerCon and XLR 5-Pin
connectors. The IP65 version is fitted with trailing leads.
The IR Remote is included in the fixture package.
2.
Safety
1. This product is for professional use only. It is NOT intended for domestic or outdoor use.
2. The bright flash of light during power-up & continuous strobe may cause epileptic seizure.
Caution
Caution
Caution
Caution
3. This product must be used with safety cable.
3.
Cabling
The Color One 100 (IP20 version) is built with chassis mount powerCon connectors for power input/through and chassis
mount XLR 5-pin for DMX input/through.
The Color One 100 (IP65 version) is built with trailing leads for power input/through and XLR 5-pin trailing leads for DMX
input/through.
The chassis is ground bonded.
4.
Mounting
The Color One 100 is built with a dual yoke system for floor mounting and overhead hanging applications. Secure the
fixture with a safety bond. A provision for the fixing hold is built into the enclosure.
5.
Optics
The Color One 100 is built with optical lens that provide a fully homogenised beam angle of approximately ~20°.
6.
Control
The control functions are accessed through the LCD display at the rear with 4 push buttons:
Back Arrow
Up Arrow
Down Arrow
Exit
Power-Up Display:
The software version is displayed on power up then proceeds to the Main Menu. The Main Menu shows the model name,
DMX status and start address, set control mode and number of assigned DMX channels.
Display Mode:
The LCD display is backlit when you access the menu and turns off when left undisturbed for 5 seconds.
IR Remote:
The remote infrared control unit features control buttons for: On/Off, Dim Up/Down, various colours, white and 4 effects: Full
Color Roll (Flash), Warm Color Roll (Strobe), Fade In/Out (Fade), Cold Color Roll (Smooth). Set the fixture for IR Remote control
by selecting IR Remote in the menu No DMX Present. Point the IR Remote towards the fixture.
Control Menu
To navigate the Control Menu options from the Main Menu,
Use the Up and Down arrows to navigate the control menu options
•
Color One 100 Quick Start Guide V1.5
(Enter) Stores the menu choice
Increases (+) the mode level or value
Decreases (-) the mode level or value
Back to the previous menu
Press the Back arrow (Enter) to select a control menu option
•
Press the Back arrow (Enter) to save the setting and display shows Done
•
Press Exit to return to the Main Menu
•
Main Menu
Main Menu
Main Menu
Main Menu
DMX Address
DMX Address
DMX Address
DMX Address
From the Main Menu, press Enter to adjust the DMX start address
1 1 1 1 - - - - Personality
Personality
Personality
Personality
Select from the following control mode options:
Mode
Display
Ch
Description
1
1-RGBA
4
RGBA
2
2-RGBAI
5
RGBA + Intensity
3
3-HSI
3
Hue + Saturation + Intensity
4
4-RGB
3
RGB (*Magic Amber)
5
5-MLED RGB
3
RGB
6
6-Master
0
Master Standalone
7
7-Slave
0
Slave Standalone
2 2 2 2 - - - - No No No No DMX
DMX Present
Present
DMX
DMX
Present
Present
If DMX is not detected, various output options can be selected:
1-OFF
Fixture has no light output
2-Hold Last
Fixture holds the last valid DMX state
3-IR Remote
Fixture is controlled via remote infrared control unit
4-Look 1
Fixture snaps to Blue
5-Look 2
Fixture snaps to Cyan
6-Look 3
Fixture snaps to Magenta
7-Look 4
Fixture snaps to Yellow
8-Look 5
Fixture snaps to White
3 3 3 3 - - - - Look Store
Look Store
Look Store
Look Store
5 internal preset Looks are available in standalone operation.
To recall a Look in standalone operation, use the Up/Down arrows to scroll through Look 1-5, then press Enter to
recall the Look.
Looks can be recorded and assigned to Looks 1-5, and will be preserved on power down. Looks will be returned to
default settings upon reset.
To create, edit and record a look in standalone mode, go to Look Store, scroll and select/recall from Look 1-5, use
the Enter to toggle between channels and the Up/Down arrows to adjust the values of each channel on the display,
press and hold Enter until the display shows Recorded, Look and Mode.
4 4 4 4 - - - - Technical
Technical
Technical
Technical
Software Version, DMX Data settings, internal Temperature and LED Calibration values are displayed; Frequency
settings of the fixture can be changed. In the Frequency menu, select from the following options: 750, 1500, 3000
and 6000 (Hz), which allows for the LED scan rate to be synchronised with the video camera and avoid a flickering
effect.
5 5 5 5 - - - - Reset
Reset
Reset
Reset
All control menu commands are reset to factory defaults: DMX address: 1, Personality: RGBA, No DMX Present: Hold
Last, Look Store: Look 1, Frequency: 750 Hz
*Magic Amber is the term used for the unit's ability to bring in amber when mixing colours that require it.
7.
Further Information
Please refer to the Chroma-Q Color One 100 manual for more detailed information. A copy of the manual can be found at the
Chroma-Q website – www.chroma-q.com – under Support.
Color One 100 Quick Start Guide V1.5
Advertisement
