Related Manuals for Chroma Color Split CHCS2
Summary of Contents for Chroma Color Split CHCS2
- Page 1 Chroma-Q™ Color Split™ User Manual Version 1.3 September 2007 Software Version 4.0 PN: 609-0500...
- Page 2 Suggestions of use shall not be taken as inducements to infringe any patent. Chroma-Q sole warranty is that the product will meet the sales specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted.
-
Page 3: Table Of Contents
Table of Contents Product Overview ……………………..………………..…………….………... 3 Operation ……………...…………………………………..…………………….…….. 3 Unpacking the unit ………………………………..………..………………… 3 Control and power cables ………………………..………..………………… 4 Diffusion Film ………………………………………………………………….. 5 Fixing ………………………………………..…………………………………. 5 Operating the unit ………………………………………..………………….. 6 Modes of operation ………………………………………………………….. 7 Technical specifications ………………………………………………….… 10 Maintenance …………………………………………………………………. -
Page 4: Product Overview
Product overview The Chroma-Q Color Split lighting fixture is designed specifically for professional entertainment lighting. The fixture’s modular design shall be suitable for creating a wide range of fixture configurations, including battens, blinders, footlights, side fills, cyclorama floods, truss toners, discreet set piece lighting and interior architectural lighting. -
Page 5: Control And Power Cables
2.2 Control and Power Cables The Color Split utilises a PowerCon cable system for power input and through and the XLR 5- pin cable system for ANSI E1.11 USITT DMX 512-A data signal input and through. The XLR 5- pin cables are wired pin to pin in the format shown in the table below. The chassis are ground bonded. -
Page 6: Diffusion Film
2.3 Diffusion Film The Color Split has a 5 degree diffusion film integrated into one cell and a 20 degree diffusion film integrated into the other cell. Printed at the bottom plate are “chevrons” that indicate the side with the 20 degree diffusion film. -
Page 7: Operating The Unit
Finally, use the butterfly latch to secure the fixtures together tightly (maximum of 3 units together). Yoke Kit The Color Split fixture is supplied with a detachable yoke kit for a single fixture with fibre washers and thumb wheels. An M10 flat washer is provided as a spacer for the side with protruding pins. -
Page 8: Modes Of Operation
The Factory default settings put the unit in its normal operating mode. DMX Address = 001 Display = dP0 Mode = oP1 Effects = F05, c26 'User' default settings Each time the RED record button is pressed, the unit will save that change and these 'user defaults' will take precedence on the next power cycle. - Page 9 Mode 7 ‘oP7’: Dual control (for 2 cells x 16 LEDs) in 6 channel HSI and 2 channel for Effects: gives 2 sets of 2 colour channels for hue and saturation, 2 sets of separate intensity channels, 1 channel for colour roll speed and 1 channel for colour range. Colour Roll Speed: 0% - Off;...
- Page 10 b. Control Menu Note: Press the ENTER (red) and UP (blue) or DOWN (black) button to move between modes and press ENTER to record any changes made. Cell Mode Display Name DMX Ch Channels Control RGBhA Single Channel 1 = Red Channel 2 = Green Channel 3 = Blue RGBA...
-
Page 11: Technical Specifications
Stand-Alone Press ENTER to access ‘F00-F99’ steps; press UP (blue) or DOWN (black) button to move between steps and press Enter to record any changes made. The F setting is accessible only in ‘oP9’. ‘F00-F09’ 10 speeds full colour roll ‘F10-F19’... -
Page 12: Accessories
2.9 Accessories CHCBBK20 20 degree beam kit for Color Block/Split CHCBBK30 30 degree beam kit for Color Block/Split CHCBBK3005 30 x 5 degree beam kit for Color Block/Split CHCBBK6010 60 x 10 degree beam kit for Color Block/Split Drawings 3.1 Outside dimensions 250mm / 9.8”...