Page 3
Ordering Assistance, Service & Inquiries Service and PESA Switching Systems, Inc. 330A Wynn Drive Ordering Huntsville, AL 35805 Main Numbers: Assistance Tel: (256) 726-9200 Fax: (256) 726-9271 Service Department Numbers: Tel: (256) 726-9222 Fax: (256) 726-9268 National Sales Office Sales Office PESA Switching Systems, Inc.
Page 4
PESA reserves the right to change any information con- NOTE tained in this manual without notice. Unauthorized copying, modifications, distribution, or display is prohibited. All rights reserved. Please address all comments or suggestions concerning this or other PESA manuals to: Publications Department Attn: Charles E.
Page 5
Notice Marking by the symbol indicates compli- ance of this PESA system to the EMC (Electro- magnetic Compatibility) directive of the Euro- pean Community. Such marking is indicative that this PESA system meets or exceeds the follow- ing technical standards: NOTICE •...
Page 6
ATTENTION ALL EQUIPMENT ITEMS MANUFACTURED BY OR SOLD BY PESA SWITCHING SYSTEMS, INC. ATTENTION SHOULD BE SERVICED BY QUALIFIED SERVICE PERSONNEL OR BY QUALIFIED SERVICE...
1.1 Manual Overview This manual provides detailed instructions for installing and operating the PESA Jaguar Audio Routing Switchers. This manual is divided into seven sections as shown. Sections 3 and 4 contain operational and functional descriptions of the Jaguar Audio Routing Switchers and their associated circuit cards.
The Jaguar Analog Audio and Digital Audio Routing Switchers are designed with mid-range size routing matrix applications in mind. These cost efficient routers are expandable up to and beyond a 128X128 size matrix. Jaguar Audio Frames utilize plug-in circuit cards for ease of maintenance and component replacement.
Jaguar Audio Introduction Section 1 1.3 Analog Audio Switcher Specifications INPUT CHARACTERISTICS Level +28dBm Max Impedance >60K Ohms Type Electronically Balanced Coupling Direct (DC) Common Mode Rejection Ratio -80dB (50Hz to 60Hz) Connector Type 3-Pin, 2-Part, Detachable Plug OUTPUT CHARACTERISTICS...
Jaguar Audio Introduction Section 1 1.5 Audio Frame Specifications POWER REQUIREMENTS Dual Range 115VAC ±10% and 220VAC ±10%, 47Hz - 63Hz (Auto Range) IEC380 Standard Power Sockets SAFETY STANDARDS (APPLIED FOR AGENCY APPROVALS) UL, CSA, VDE, and CE RFI AND EMI STANDARDS...
• System Connections General If specified when ordered, the Jaguar Audio Frame will be configured for the intended system at the factory. Before attempting to install any frame, matrix card, controller card, or power supply; this section should be read carefully.
GROUND WRIST STRAP AND GROUNDING MAT BE USED BEFORE ATTEMPTING ANY EQUIPMENT INSTALLATIONS. 2.2 Receipt Inspection The Jaguar Audio Routing Switcher was tested and inspected prior to leaving the factory. Upon receipt, inspect the equipment for shipping damage. If any damage is found, contact the carrier immediately and save all packing material.
Digital Audio Output Combiner Cards (Optional) 2.4 Location Both models of the Jaguar Audio Routing Switcher may be located any- where power is available. However, units should be mounted as close as possible to their associated equipment to minimize cable runs. Forced air cooling is provided by a fans located at the back of the units.
5. Tighten all of the screws until they are secure. 2.6 Cabling Considerable weight will be added to the rear panel of the Jaguar Audio Routing Switchers by the control, signal, and power cables. Therefore, all cables should be strain relieved and secured to racks or other supporting structures.
2.7 Level Code (Strobe) Selection The level (strobe) select switches, S3 (matrix A) and S6 (matrix B) are located on the inside of the Jaguar Audio Routing Switcher on upper middle and lower middle, respectively, of the backplane. For all switch position to binary code conversions refer to Table 2-3.
2.8 Output/Input Code Selection The input and output coding switches for matrix "A" (S2 and S1 respec- tively) are located on the inside of the Jaguar Audio Routing Switcher on the upper middle of the backplane. The input and output coding switches for matrix "B"...
Jaguar Audio Installation Section 2 2.8 Input/Output Code Selection Continued: Output Code Physical 0 (Logical 1) = OFF (UP) Physical 1 (Logical 0) = ON (DOWN) NOTE: The following are logical selections. Output code 0 is all switches on (down) or all switches in the physical 1 position.
Jaguar Audio Installation Section 2 2.8 Input/Output Code Selection Continued: Input Code Physical 0 (Logical 1) = OFF (UP) Physical 1 (Logical 0) = ON (DOWN) NOTE: The following are logical selections. Input code 0 is all switches on (down) or all switches in the physical 1 position.
Jaguar Audio Installation Section 2 2.9 Analog Audio Matrix Card Line and Sync Selection The 64X32 Analog Audio Matrix Card's line and sync select switch, SW1, is located in the lower, right side of the 64X32 Analog Audio Matrix Card.
Jaguar Audio Installation Section 2 2.9 Analog Audio Matrix Card Line and Sync Sel. Cont: Figure 2-6 64X32 Analog Audio Matrix Card Line and Sync Switch Location 2.10 Digital Audio Matrix Card Line and Sync Selection The 64X32 Digital Audio Matrix Card's line and sync select switch, S1, is located on the lower, right side of the 64X32 Digital Audio Matrix Card.
Jaguar Audio Installation Section 2 2.10 Digital Audio Matrix Card Line and Sync Sel. Cont: Figure 2-7 64X32 Digital Audio Matrix Card Line and Sync Switch Location 2.11 Output Monitor Card Level Code (Strobe) Selection The Output Monitor Card's level (strobe) select switch, S3, (a binary coded switch) is located on the front edge of the Output Monitor Card.
Jaguar Audio Installation Section 2 2.12 Output Monitor Card Input/Output Coding Select. The Output Monitor Card's input and output code select switches are located on the front edge of the Output Monitor Card. For all switch posi- tion to binary code conversions refer to Table 2-3.
Jaguar Audio Installation Section 2 2.12 Output Monitor Card In/Out Coding Select. Cont: Output Code Physical 0 (Logical 1) = OFF (DOWN) Physical 1 (Logical 0) = ON (UP) NOTE: The following are logical selections. Output code 0 is all switches on (up) or all switches in the physical 1 position.
2.14 PS130 Power Supply Installation The PS130 Power Supplies are installed in the upper, right-hand portion of the front of the Jaguar Audio Routing Switcher. The Jaguar Audio Routing Switcher is designed for the internal installation of up to two PS130 Power Supplies.
2.15 Reference Interface Card Installation The Reference Interface Card is installed in the lower set of the stand-off circuit card guides (between card slots 2 and 3) in the Jaguar Audio Rout- ing Switcher. To install the Reference Interface Card in the Jaguar Audio Routing Switcher take the following steps while referring to the Jaguar Audio Mainframe configuration drawing on page 6.2:...
6.2: 1. Align the shield plate on the first 64X32 Matrix Card with the upper set of circuit card guides in the lower portion of the front of the Jaguar Audio Routing Switcher. 2. Carefully push the 64X32 Matrix Card into the Jaguar Audio Routing Switcher until the matrix card connectors make initial contact with the backplane connectors.
2.17 Standard Audio Output Card Installation The Standard Audio Output Cards are installed on the left-hand side of the rear of the Jaguar Audio Routing Switcher. The Jaguar Audio Routing Switcher is designed for the installation of two Standard Audio Output Cards.
Jaguar Audio Frame and on the card cage extension. 3. Once the inverted "L" assembly is aligned with the corresponding screw holes, attach it to the rear of the Jaguar Audio Frame and to the card cage extension using six Phillips head screws.
2.21 Rear Panel Connectors These manual subsections discuss the various system connectors found on the rear of a fully configured Jaguar Audio Routing Switcher. Refer to Figure 2-13 and to Jaguar Audio Mainframe Assembly configuration drawing on page 6.3 for visual references.
Figure 2-13 Jaguar Audio Routing Switcher Rear View DC Power In/Out Connector Power can be supplied to the Jaguar Audio Routing Switcher by the use of an externally mounted power supply or by the use of internal PS130 Power Supplies. The DC Power In/Out Connector can be used as DC...
The AC Power Connector enables the connection of the AC line to the Jaguar Audio Routing Switcher. The AC line input voltage can be from 100 - 240 VAC and the AC line frequency range can be from 47 - 63 Hz.
Reference (Sync) Connectors (1 and 2) The sync connectors are used to connect an external sync signal to the Jaguar Audio Routing Switcher. The sync signal may be either a color black or composite sync signal. The use of an external sync signal allows switch changes to be accurately timed in the vertical interval.
Audio Input Connectors There are 64 matrix "A" and 64 matrix "B" audio input connectors located on the rear of the Jaguar Audio Routing Switcher when the Jaguar Frame is configured as a 64X64 stereo routing switcher. When the Jaguar Frame is configured as a 128X64 mono routing switcher matrix "A"...
5-Pin Control Connector on the primary Jaguar Routing Switcher to 5-Pin Control Connector on the other Jaguar Audio Routing Switcher using a 5-pin cable. 3. Connect the external controller (a stand-alone System Controller or a control connection from a Jaguar Video Frame) to the 9-Pin Control Connector using a 9-pin RS232 cable or the 5-Pin Control Connector using 5-pin ribbon cable.
Section 3 3.1 Introduction This section details the Jaguar Audio Routing Switcher operational proce- dures. The operation of the Jaguar Audio Routing Switcher consists of periodically monitoring the power supply and circuit card LEDs. The fol- lowing topics are discussed: •...
Jaguar Audio Operations Section 3 3.3 Dual Reference Interface Card Operation Cont: Sync #2A Fail LED (Red) The Sync #2A Fail LED (CR10), located on the front edge of the interface card, is utilized to visually indicate that external sync number two "A" has failed or is missing.
Jaguar Audio Operations Section 3 3.4 Analog Audio Matrix Card Operation The operation of the Jaguar Analog Audio Matrix Card consists of periodi- cally monitoring the matrix card's LEDs. The matrix card LEDs and their proper indications are discussed in the following manual sections.
Jaguar Audio Operations Section 3 3.5 Digital Audio Matrix Card Operation Continued: Power OK LED (Green) The Power OK LED (CR9) on the front edge of the matrix card is utilized to visually indicate that the proper power supply voltage is being supplied to the card.
The backplane is also responsible for dis- tribution of power from the power supplies to the Jaguar Audio Frame's circuit cards and to the chassis fans. An additional function of the backplane is to distribution control and communication signals to and from the matrix cards, monitor control card (if installed), and control ports.
4.4 Dual Reference Interface Card The Dual Reference Interface Card is responsible for providing sync signals to the Jaguar Audio Frame. The sync signals provided by the Dual Refer- ence Interface Card can either be derived from composite sync or color black signals or generated internally by the Dual Reference Interface Card.
U8 (inverter) and to U10 (quad two- input or gate). U8 and U10 along with U14 form a gating network that passes the external sync signal to the Jaguar Audio Frame when an exter- nal sync signal is present.
Jaguar Audio Functional Section 4 4.5 64X32 Analog Audio Matrix Card Continued: Control Continued: Matrix output, input, and level coding is read from the backplane through U290, U305, and U306 respectively for matrix A and U293, U292, and U291 respectively for matrix B. U277, U295, U276, and U307 provide ad- dress decoding for the 64X32 Audio Matrix Card.
Jaguar Audio Functional Section 4 4.5 64X32 Analog Audio Matrix Card Continued: Input The input circuits on the 64X32 Audio Matrix Card provide the initial condi- tioning and termination of the audio input signals. The input circuits are comprised of an operational amplifier and its associated components.
Jaguar Audio Functional Section 4 4.6 64X32 Digital Audio Matrix Card The 64X32 Digital Audio Matrix Card contains a 64X32 matrix consisting of several main circuits. This discussion will be broken down to the main circuits as they are found on the schematics in Section 6 (Schematics).
Jaguar Audio Functional Section 4 4.6 64X32 Digital Audio Matrix Card Continued: Input Equalizers U1 thru U4 and U41 thru U44 provide adequate input cable equalization for matrix A inputs dependent upon the quality of the input cables. U21 thru U24 and U61 thru U64 provide adequate cable equalization for matrix B inputs dependent upon the quality of the input cables.
The electronic circuits on the Analog Audio Output Combiner Card are re- sponsible for combining two outputs from the 64X32 Analog Audio Matrix Cards to form one output from the Jaguar Audio Frame. The circuits on the Analog Audio Output Combiner Card consist of eight 2X1 summing combiner circuits, control circuits, and a power regulation circuit.
Page 57
Jaguar Audio Functional Section 4 4.9 Optional Output Monitor Control Card Continued: The microprocessor controller (U13) is used to interface commands from the system controller and return status information to the system control- ler. Communications to and from the system controller are through U6, a RS485 receiver and transmitter.
There is no need to perform periodic adjustments and the need for regular maintenance is minimal. 5.3 Test Equipment The test equipment recommended for servicing the Jaguar Audio Switch- ers and their associated circuit cards is listed below. Equivalent test equip- ment may be used.
5.5 Maintenance The Jaguar Audio Switchers and their associated circuit cards are de- signed and manufactured to give long, trouble free service with minimum maintenance requirements. If problems do occur, follow the troubleshoot- ing procedure provided in this section.
If desired, equipment or boards may be returned to the factory (transporta- tion prepaid) for repair. Refer to the General Assistance and Service Information Sheet in the front of this manual. Call the PESA Service Department (the phone number is listed on the Service Information Sheet) for a RMA number before shipping an equipment item.
Replacement Parts Only parts of the highest quality have been used in the design and manufacture of the Jaguar Audio Switchers and their associated circuit cards. If the inherent stability and reliability are to be maintained, replacement parts must be of the same quality. A replacement parts list is provided in Section 7 of this manual.
Schematics Section 6 6.1 Schematics General This section contains the schematic diagrams and parts location diagrams for the Jaguar Audio Routing Switchers. Please refer to this section when troubleshooting the equipment or replacing defective parts. Description Dwg No. Page No.
Jaguar Audio Schematics Section 6 NOT AVAILABLE AT TIME OF PRINTING Configuration Drawing (Sheet 1 of 2) • Jaguar Audio Mainframe Assembly • CD63-0768 3/98 P/N 81905903730 page 6.2 SCHEM A TI C S...
Page 64
Jaguar Audio Schematics Section 6 Configuration Drawing (Sheet 2 of 2) • Jaguar Audio Mainframe Assembly • CD63-0768 3/98 P/N 81905903730 page 6.3 SCHEM A TI C S...
Page 65
Jaguar Audio Schematics Section 6 NOT AVAILABLE AT TIME OF PRINTING Configuration Drawing • Jaguar Chassis Assembly • CD63-0766 3/98 P/N 81905903730 page 6.4 SCHEM A TI C S...
Jaguar Audio Schematics Section 6 NOT AVAILABLE AT TIME OF PRINTING Configuration Drawing • Card Cage • CD63-0767 3/98 P/N 81905903730 page 6.55 SCHEM A TI C S...
Page 117
Jaguar Audio Schematics Section 6 Component Assembly • 128X64 Analog Audio Output Combiner Card • CA25-1324 3/98 P/N 81905903730 page 6.56 SCHEM A TI C S...
7.1 Parts List General The Parts List in this section have been grouped according to each as- sembly associated with the Jaguar Audio Switchers. Refer to each list by name of card, board, or section of the equipment requiring replacement parts.
Jaguar Audio Parts List Section 7 Output Monitor Control Card - 81906518460 81901000840 CAP 0.1F 5.5V 81901601187 REG MC7805C +5V 1A TO-220 81901606730 IC 68HC11E9 SINGLE CHIP 81901606830 IC 7.3728 MHZ OSCILLATOR XTAL1 81902105050 LABEL BARCODE 1.5"x0.25" 81902413340 PCB AUDIO OUTPUT CONTROL...
Page 147
Jaguar Audio Parts List Section 7 Output Monitor Control Card - 81906518460 Continued: CA25-1334 DOC AUDIO OUTPUT MON CTRL 0 DD52-1334 DOC AUDIO OUTPUT MON CTRL 0 NOT-PLACED ITEMS NOT PLACED ON EBOM TP1 TP2 SC33-1334 DOC AUDIO OUTPUT MON CTRL 0...
Page 148
AC line input is disconnected. *NOTE* The PS130 Power Supply replaces the power supply formerly used to power the PESA equipment item referenced in the technical manual to which this addendum is attached. This addendum takes precedence over any mention of the former power supply in the technical manual for any PESA equipment items where the PS130 Power Supply is uti- lized.
*CAUTION* Disconnect AC Power Cord Before Removing Power Supply. In the event of a PS130 Power Supply failure, PESA suggets returning the malfunctioning unit to the PESA Service Department for replacement. PS130 Power Supplies contain lethal voltages when operating and should only be serviced by technicians qualified to service off-line switching regulators.
Page 150
Front Door Removal and Replacement Front Door Removal (Removable Front Doors Only) To remove the PESA equipment item's front door (cover) take the follow- ing steps: 1. Grasp the both the left and right front cover slide locks and push or pull them towards the center of the equipment item's front.
1. Align the front door with the front of the PESA equipment item. 2. Once the front door is aligned with the front of the PESA equipment item, slide the front door onto the equipment item until the slide locks snap into the locking provided on the equipment item's chassis.
Internal PS130 Power Supply Addendum 2. Carefully push the power supply into the chassis until the power supply connector makes initial contact with the backplane power connector. At this point, firmly but carefully continue pushing the power supply into the equip- ment chassis while making sure the power connectors are properly aligned.
Need help?
Do you have a question about the Jaguar Audio and is the answer not in the manual?
Questions and answers