Table of Contents
Advertisement
RE4QS/EX (TLS-S8000P GB) Wed. May, 23/2001
OUTPUT TERMINALS
SW OUT Terminal
When recording, a pulse signal is output at the SW OUT
terminal.
This terminal is usually connected to the switch input
(SW IN) of devices like a camera switcher unit, or a
quad compressor.
FIELD: 20 msec.
FRAME: 5 msec.
(Output impedance: 5.7 kΩ)
SW OUT Terminal Output Setting
1
Press the MENU button until the (SET UP 4) menu
is displayed.
Y The "TIMING" setting is flashing.
@@@@@@@<SET@UP@4>
*SW@OUT
@@TIMING@@@@@@@@FIELD
@@FIELD@@@@@@@@@01
@@3H@@@@@@@@@@@@Y
*THREAD@CHECK@@@Y
*VIDEO@LOSS@@@@@N
*REC@SPEED@@@@@@N
2
Turn the SHUTTLE ring, to set "FIELD" or "FRAME".
FIELD . . . . . . 1 pulse is output after each set
number of fields.
FRAME . . . . . 1 pulse is output after each set
number of frames.
3
Turn the JOG dial clockwise until the "FIELD" (or
"FRAME") setting is flashing.
NOTE:
X If "TIMING" is set to FRAME (see step 2),
"FRAME" will be indicated instead of "FIELD".
4
Turn the SHUTTLE ring, to set the desired pulse
signal interval.
Available settings are:
FIELD . . . . . . 01, 02, 03, 04, 05, 10, 30 or 60
field
FRAME . . . . . 01, 02, 03, 04, 05, 10, 30 or 60
frame
5
Turn the JOG dial clockwise until the "3H" setting is
flashing.
6
Turn the SHUTTLE ring, to set the desired "3H"
mode.
Y . . . . . . . . . . When recording in 3-hour mode,
a pulse signal is output.
N . . . . . . . . . . When recording in 3-hour mode,
a pulse signal is not output.
7
Press the SEARCH/AUDIO ON button to save the
settings.
English
SERIES OUT/NON REC OUT terminal
setting
The output at the SERIES OUT/NON REC OUT
terminal can be set.
1
Press the MENU button until the (SET UP 1) menu
is displayed.
5V (H)
0V (L)
2
Turn the JOG dial, until the "OUTPUT" setting is
flashing.
3
Turn the SHUTTLE ring, to select the desired
output mode.
SERIES . . . . If during series recording, the
NON REC. . . If during recording the VCR
4
Press the SEARCH/AUDIO ON button to save the
setting.
41
@@@@@@@<SET@UP@1>
*LANGUAGE-LANGUE-SPRACHE
@@@ENGLISH
*CLOCK@SET
@15-10-2001@MON@15:20:00
*SUMMER@TIME@SET@@USE
@@@@@@@@WEEK@MONTH@TIME
@ON@@@LST-SUN@@03@02:00
@OFF@@LST-SUN@@10@02:00
*OUTPUT@@@@@@@@SERIES
*REMOTE@@@@@@@@EJECT
counter reading reaches
2
57
00
or the tape reaches
H
M
S
the end, a LOW signal (0 V) is
output. The LOW (0 V) signal is
output for about 10 seconds after
the end of the tape is reached.
enters a mode other than
recording (i.e. recording pause,
stop mode, etc.), a LOW signal (0
V) is output. If recording is
resumed, then a HIGH signal (5
V) is output.
If in the (SET UP 2) menu, in the
BUZZER section, WARNING is
set to "Y", a buzzer will be heard
while the VCR is in non recording
mode. The buzzer will stop if the
STOP button is pressed (the
output signal will remain LOW (0
V)).
Advertisement
Table of Contents
