Dss Or Satellite Receiver - Ada PTM-6150 Operation & Installation Manual

DSS or Satellite Receiver

The Cinema Reference is preprogrammed to permit you to easily
connect a DSS or Satellite Receiver.
Standard RCA interconnects are used for the audio connection while
a 75Ω coax cable is used for the video connection.
Connection 1 - DSS Audio Output - You will need to connect the
DSS's audio output (stereo RCA type) to the Cinema Reference's
Audio Input #5.
Connection 2 - DSS Receiver's Video Output - You will need to con-
nect the DSS's video output (Composite Video) to the Cinema
Reference's #5 Video Input.
Connection 3 (Optional) - DSS's S-Video Output - You may also
choose to connect the S-Video (Super Video) output of the DSS to
the Cinema Reference's #2 S-Video Input. This will require a spe-
cial super video cable. Please note, if your projector or TV does not
have a super video input, you will not need to make this connection
as the Cinema Reference does not cross convert S-Video to Com-
posite Video.
Connection 1
Stereo
Audio Out
R
Video
Cable
5
VIDEO INPUTS
1 3 5
2 4 6
1 2 3
L
5R
R
Stereo AudioCable
(This cable carries standard 2 channel audio)
Page 26
Connection 2
DSS/SATELLITE
Video S-Video
Out Output
L
OFF ON DC Input Mute Switch
1
LASER DISC PLAYER
Dolby Digital (AC-3)
RF Switcher & AC-3
2
RF Demodulator
VIDEO OUT
2
7 1 REC
S-VIDEO OUT S-VIDEO INPUTS
MAIN 1 2
REC
8 2 OSD
AUDIO INPUTS AUDIO OUTPUTS
4 5 6 7 8 REC
5L
L L L
R
R R
OUT
Connection 3
Optional S-Video Cable
(Only functional if you connect your TV or Projector
to the Cinema Reference's "Main" S-Video Output.)
Connections!
In order to play an AC-3 Laser
Disc, you must connect the Digital
AC-3 Output to a Digital Audio
Input (RCA Type Coax) below.
HDTV/RGB
COMPONENT
VIDEO
4
3 SWITCHER
Use With DVD
Players or
Cb
Digital Video
Tape Players
1 2 OUT
DIGITAL AUDIO INPUTS
L LS SUB In order to play an AC-3 Laser Disc, 1 3
you must connect the Digital AC-3
Output to a Digital Audio Input.
OPTICAL INPUTS
1 2 3
R RS C 2 4
For DSS or SAT Receivers that
sport a Digital output, you
may select to alter the Cinema
Reference's "Out Of The Box"
setup to switch the audio for
the DSS/SAT Receiver to a
digital input that is not used.
1 Turn the Input knob to
DSS/SAT 6 and press the
knob.
2 Turn the Mode knob
clockwise to SETUP MODE
and press the knob.
3 Turn the Mode knob to
AUDIO INPUT and press the
knob. Once the knob is
pressed the display will read
"ANALOG IN 5".
4 Turn the mode knob
until the display reads the cor-
responding digital input that
you have connected your DSS
to and press the knob.
Cinema Reference
15
Y Manufactured under license from Dolby Laboratories Licensing Corp.
"Dolby", "Dolby Digital", "Pro Logic", & the Double-D Symbol are the trademarks of Dolby Laboratories Licensing Corp.
Manufactured under license from DTS Technology, LLC. DTS Digital Surround is a trademark of DTS Technology LLC.
Manufactured under license from Lucasfilm Ltd. U.S. patent numbers 5,043,970; 5,189,703; and 5,222,059.
Foreign patents pending. Lucasfilm and THX are registered trademarks of Lucasfilm Ltd.,
Cr WARNING! Risk Of Hazardous Energy!
CAUTION
Make Proper Connections.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVERTISSEMENT! Energie Electrique Dangereuse!
Faire Des Connexions Propres Pour L'Hautparleur.
ATTENTION!
Voir La Notice De Fonctionnement.
RISQUE DE CHOC ELECTRIQUE.
NE PAS OUVRIR
CAUTION: Disconnect Supply Cord Before Servicing.
MADE IN U.S.A.
ATTENTION: Debrancher Avant Le Depannage.
LOW VOLTAGE
DATA PORT
12VDC OUT
Serial Data 100mA Max Per
ADA Bus™ DC 1 DC 2
1 2 3 4 1- 2+ 1- 2+
AC OUTPUT AC INPUT
10A Max Switched 115V-60Hz/230V-50Hz
Voltage
Selector &
Safety Fuse
On This Side
115 V
115V 230V
Use Same
Value Fuse
115V-1AS.B.
230V-.5AS.B.