Star SM-S220I SERIES Hardware Manual

Hide thumbs Also See for SM-S220I SERIES:

Advertisement

Quick Links

Mobile Printer
SM-S220I SERIES
Hardware Manual

Advertisement

Table of Contents
loading

Summary of Contents for Star SM-S220I SERIES

  • Page 1 Mobile Printer SM-S220I SERIES Hardware Manual...
  • Page 2 [Swedish] och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Español: Por medio de la presente STAR MICRONICS CO.,LTD. declara que el Wireless Device cumple con los requisitos esenciales y cualesquiera [Spanish] otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Português: STAR MICRONICS CO.,LTD. declara que este Wireless Device está conforme com os requisitos essenciais e outras disposições [Portuguese] da Directiva 1999/5/CE.
  • Page 3: Trademark Acknowledgments

    [Norwegian] relevante krav i direktiv 1999/5/EF. Íslenska: Hér með lýsir STAR MICRONICS CO.,LTD. yfir Því að Wireless Device er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í [Icelandic] tilskipun 1999/5/EC. This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
  • Page 4: Using The Printer

    If you notice smoke, a strange smell, or a strange sound, turn off the power immediately, and remove the battery pack and battery charger. Then contact a Star Micronics dealer. The battery pack may be hot immediately after the product has been used.
  • Page 5: Printer Maintenance

    Operating Environment for the Printer Before actually unpacking the printer, you should take a few minutes to think about where you plan to use it. Remember the following points when doing this. Do not use the printer in an environment in which it will be subject to strong shaking while it is printing.
  • Page 6: Table Of Contents

    Table of Contents 1. Product Overview ..............1 1.1 Printer & Accessories ..................2 1.2 External Appearance and Part Names ............3 2. Setup ..................4 2.1 Buttery Pack ....................4 2.1.1 Inserting into the Printer ................... 4 2.1.2 Charging the Battery ................... 4 2.2 Bluetooth Settings ..................
  • Page 7: Product Overview

    1. Product Overview This printer is perfect for mobile banking systems, retail, POS (point of sale) terminals and other forms of mobile computing. The characteristics of this printer are listed below: • Pocket size (82×140×47 mm) • Extremely light and mobile (289 g) •...
  • Page 8: Printer & Accessories

    1.1 Printer & Accessories The printer is packaged with the following accessories. If any of these accessories is broken or missing, please contact the dealer that you bought the product. Printer Battery Pack Printer paper sample Belt Clip and Score Serial Communication Cable Battery Charger Safety Instruction Sheet...
  • Page 9: External Appearance And Part Names

    1.2 External Appearance and Part Names Printer Cover Cover Open Lever *With protective lm FEED Button MODE Button COM1(Serial 6P) POWER Lamp For connecting to the host device ERROR Lamp COM2(NFC/PED 8P) For connecting to a PIN pad or RFID module * The LCD and Cover Open Lever are covered with a protective film.
  • Page 10: Setup

    2. Setup 2.1 Battery Pack 2.1.1 Inserting into the Printer 1. Make sure that the printer has been turned off before you insert or remove the battery pack. 2. Insert the battery pack into the back of the printer as in the figure shown below, follow- ing the direction of the arrow. Hook 3. To remove the battery back, pull back the hook, and use the opposite procedure from the one you used to insert the battery pack.
  • Page 11 Notes about the Battery Pack u General Battery Characteristics • The battery is a consumable and its performance over time will gradually decrease. • While not in use, the battery will slowly discharge itself. Prepare a battery pack that has been charged relatively recently (1 to 2 days earlier). •...
  • Page 12 u Notes about Storing the Battery Pack • The characteristics of the battery pack may degrade if you store it in a charged state for a long period of time. If you do not intend to use the battery pack for a while, use up its power before storing it. • If you do not intend to use the battery pack for a long time, be sure to remove it from the printer, and do not leave it connected to a battery pack holder for external charging.
  • Page 13: Bluetooth Settings

    2. If necessary, enter the following information into the terminal that you are using. PIN: 1234 (default) Device name: Star Micronics (default) For security purposes, we recommend that you change the PIN. For details about changing the PIN, please contact with our dealer.
  • Page 14: Memory Switch Settings

    2.3 Memory Switch Settings Change the Memory switch by this operation. (Refer to “Memory Switch Setting Table”). MODE button : Changing OPTION status. FEED button : Changing PRINTER MODE status * Example: When you want to switch from the default settings to the following settings. Bluetooth / 9600 bps / Even Parity /...
  • Page 15 8. Press FEED once to switch the displayed setting from the black mark sensor mode to the black mark sensor sensitivity. The current black mark sensor sensitinity will appear on the display. 5 Press MODE twice to set the black mark sensor sensitivity to medium2. SENSOR LOW g SENSOR MIDIUM1 g SENSOR MIDIUM2 9.
  • Page 16 Memory Switch Setting Table Printer Mode Setting Display Bluetooth(iOS) * Bluetooth(iAP) Communication Port *1 ) Bluetooth Bluetooth Mode RS-232C UART Mode 9600 bps 9600 BPS Baud Rate 38400 bps 38400 BPS 115200 bps * 115200 BPS No Parity * NO PARITY Parity Bit Odd Parity ODD PARITY...
  • Page 17: Loading Paper

    2.4 Loading Paper Refer to chapter 4, “Paper” (p. 17), to select roll paper that conforms to the specifications. 1. Turn on the printer. 2. Put your finger on the lever for opening the cover, and then open and raise the printer cover.
  • Page 18 4. Press down on both sides of the printer cover to close it firmly. When you close the printer cover, make sure that it is closed on both sides. 5. Use the tear bar to cut the extra paper. CAUTION When the paper is jammed, be sure to open the printer cover before removing the jammed paper.
  • Page 19: Belt Clip

    2.5 Belt Clip 2.5.1 Attaching to the Printer Follow the procedure below to attach the belt clip to the printer. 1. Make sure that you are attaching the belt clip in the right orientation, then screw the screw that comes with the belt clip into the designated screw hole to attach the belt clip to the printer.
  • Page 20: Printer Feathres

    3. Printer Features 3.1 Control Panel Bluetooth Mode 3.1.1 Buttons 1) FEED button: When the printer is on, you can press FEED to feed the paper. 2) MODE button: You can change the communication mode and print settings by configuring the printer’s mode settings.You can configure the mode settings after you press and hold MODE for 5 seconds or more and the ERROR LED flashes five times. (For more information about mode settings, see section 2.3, “Memory Switch Settings.
  • Page 21 n LED & LCD Display / Error Printer Status Action Buzzer POWER ERROR (Green) (Red) Display : [ Bluetooth Mode ] Printer Initialization(Power On) Flickering Flickering Beep 3 Back Light : Flickering during initialization Display : [ Bluetooth Mode ] Stand-by Nothing Bluetooth connected / disconnected...
  • Page 22: Self Test

    3.2 Self Test You can use a self test to check the printer’s settings. Before you start the self test, make sure that roll paper has been properly loaded into the printer. 3.2.1 Self Test Procedure 1) Turn on the power while holding down FEED. 2) The printer will print the current printer status, including the firmware version, commu- nication mode, and print settings.
  • Page 23: Paper

    4. Paper 4.1 Paper Specifications Type : Thermal Paper Paper width : 57.5±0.5 mm 65±5 µm Paper thickness : External diameter : Ø40 mm or less Inner diameter : Ø12mm±1 or more Printed surface : Outer edge of roll 4.2 Recommended Paper (Common thermal roll paper) Manufacturer Product Name Mitsubishi Paper Mills Limited...
  • Page 24: General Specificatons

    5. General Specifications Item Specifications Printing method Direct line thermal printing Characters per line Maximum 42 cpl Alphanumeric characters: 12 X 24 dots, 9 X 24 dots, and 7 X 17 dots Character size Japanese characters: 24 X 24 dots Alphanumeric characters, expanded graphic characters, JIS Level-1 Kanji Set, JIS Character types Level-2 Kanji Set, and special characters...
  • Page 25 n External Specifications External dimensions: Approximately 82 mm (W) × 140 mm (D) × 47 mm (H) Weight: 289 g (printer + battery pack). * The weight of the roll paper is not included. Body color: Front g Shiny black Back g Black Side g Blue silver - 19 -...
  • Page 26: Declaration Of Conformity

    Star Micronics Co.,Ltd. Manufacturer’s Address 20-10 Nakayoshida, Suruga-ku, Shizuoka-shi, Shizuoka 422-8654 Japan Importer’s Name Star Micronics Europe Ltd. Importer’s Address Star House, Peregrine Business Park, Gomm Road, High Wycombe, Bucks. HP13 7DL, U.K. Type of Equipment Thermal Printer Model Name SM-S220 Ref.
  • Page 27 URL: http://www.starmicronics.com/support/ Rev. 1.0...

Table of Contents