Changing The Remote Control Code; Changing The Unit's Settings; Common Procedures; Entering A Password (Ratings) - Panasonic DMR-E30 Operating Instructions Manual

Changing the remote control code

DVD/TV
DVD POWER TV
DVD TV
Í Í
VCR Plus+ TV/VIDEO REC MODE REC
5
1 2 3
CH
4 6
5
VOLUME
7 8 9
CANCEL
0 100
SKIP SLOW/SEARCH
DIRECT NAVIGATOR PLAY LIST
TOP MENU
MENU
2 3
≥
ENTER
FUNCTIONS RETURN
PROG/CHECK ADD/DLT DISPLAY TIME SLIP
OPEN/CLOSE STATUS FRAME
1 6 SETUP AUDIO INPUT SELECT CM SKIP
≥
ERASE F Rec POSITION MEMORY MARKER
2 3
≥
FUNCTIONS RETURN
Most of the DVD recorders and players manufactured by Panasonic
use the same remote control system. If you have more than one
piece of equipment placed in proximity to each other, they may all
respond to the signal. If this occurs, you will have to alter the code
on the unit as well as on the remote control (the two must match)
using the following procedure.
≥Use "1", the factory set code, under normal circumstances.
50
RQT6559
!?
1
Press [SETUP] to show the menus.
SET UP
Antenna System CATV
Auto Channel Setting
Channel Caption
Channel
Preset Channel Caption
Set Up
Manual Channel Caption
Disc
Video VCR Plusi CH Setting
Audio
Display
TAB SELECT
TV Screen
RETURN
2
Press [3, 4] to select "Set Up" and
press [1].
3
Press [3, 4] to select "Remote Con-
4 5
≥ ≥
trol Code" and press [ENTER].
4
Press [3, 4] to select the code (1, 2,
or 3) and press [ENTER].
The remote control code on the unit has been set.
5
While pressing [ENTER]
remote control, press the numbered
button ([1], [2] or [3]) corresponding
to the code you selected in step 4.
The remote control code on the remote control has been set.
4 5
6
≥ ≥
Press [SETUP]
If the unit doesn't respond, you have entered the wrong code.
Repeat step 5 to enter the correct code.
[Note]
≥The following display appears on the unit's display if its code and
the remote control's code are different. Change the remote con-
trol's code to suit the unit. The display disappears after about 5
seconds.
The unit's remote control code
≥You can also set the main unit's code without using the remote
control.
1 Press [FUNCTIONS] on the main unit.
2 Press [3, 4, 2, 1] to select "SETUP" and press [ENTER].
3 Carry out procedure 2-4 above.
4 Press [RETURN].

Changing the unit's settings

VCR Plus+ TV/VIDEO REC MODE REC
Numbered
buttons
CANCEL
DIRECT NAVIGATOR
TOP
MENU
FUNCTIONS
PROG/CHECK
OPEN/CLOSE
on the
1 SETUP
ERASE

Common procedures

See page 52 for menu and option details.
1
Press [SETUP] to show the menus.
SET UP
Auto Channel Setting
Channel Caption
Channel
Preset Channel Caption
Set Up
Manual Channel Caption
Disc
VCR Plusi CH Setting
Video
Audio
Display
TV Screen
Tabs
2
Press [3, 4] to select the menu's tab
and press [1].
3
Press [3, 4] to select the menu and
press [ENTER].
4
Press [3, 4] to select the option and
press [ENTER].
The screen now shows the menu again.
≥Some items require different operations. Read the following expla-
nations.
To return to the previous screen
Press [RETURN].
When you are finished
Press [SETUP].

Entering a password (Ratings)

[DVD-V]
DVD/TV
DVD POWER TV
DVD TV
Í Í The password screen is shown when you select levels 0 to 7.
1. Input a 4-digit password with the numbered buttons.
≥If you enter a wrong number, press [CANCEL] to erase it.
2. Press [ENTER].
1 2 3
CH ≥The lock symbol appears closed to show the rating is locked.
4 6
5
≥Do not forget your password.
VOLUME
7 8 9
CANCEL
3. Press [ENTER] to confirm the 4 digits.
0 100
SKIP SLOW/SEARCH
Now, when you insert a DVD-Video that exceeds the ratings limit
you set, a message appears on the television.
PLAY LIST
Follow the on-screen instructions.
MENU
2 3 4
≥ ≥
ENTER

Digital Audio Output

[DVD-V]
RETURN
RETURN
Change the settings when you have connected equipment through
ADD/DLT DISPLAY TIME SLIP
this unit's DIGITAL AUDIO OUT terminal ( page 47, [A]).
STATUS FRAME
Select the "Audio" tab and then "Digital Audio Output" by fol-
AUDIO INPUT SELECT CM SKIP
lowing "Common procedures" (‹ left) to set up "PCM Down
F Rec POSITION MEMORY MARKER Conversion", "Dolby Digital" and "DTS".
PCM Down Conversion
Select how to output audio with a sampling frequency of 96 kHz.
Select "On" if the equipment you connect cannot process signals
with a sampling frequency of 96 kHz.
≥Select "Off" if you use analog connect irrespective of the type of
equipment.
Off (Factory preset):
Antenna System CATV
Output as 96 kHz. There is no output if the disc has copy protection.
Select "On" in this case.
On:
Converted to 48 kHz for output.
Dolby Digital and DTS
TAB SELECT
RETURN Bitstream (Factory preset for Dolby Digital):
Select if the equipment you connected can decode the signal.
Menus Options
PCM:
Select if the equipment you connected cannot decode Dolby Digital
signal.
Off (Factory preset for DTS):
Select if the equipment you connected cannot decode DTS signal.
IMPORTANT
If the equipment you connected cannot decode the signal, the
setting must be changed to PCM or Off. If not, signals the
equipment cannot process will be output by this unit, causing
high levels of noise which can damage your hearing and the
speakers.
!?
51
RQT6559